01-29-2012, 01:35 PMRed JhonRampage iv extreme - bios 1101 - instability
I started Battlefield 3, black screen after a few minutes ... The system crashed and I had to press the reset button to restart it. I raised my VCCSA to 1.18 and now it seems fine. I had another problem while restarting. My Logitech G19 not work in windows, I restarted the system and was stuck on code 99, after a few minutes threw me and said that the keyboard was not present. In windows I disconnected and reconnected the USB cable and the keyboard worked again.
Fix instability of mobo please!
01-29-2012, 01:48 PMHiVizMan
Maybe it is your overclock that is unstable my friend. :p
But I did find I have better stability with bios 1005 than 1101. :)
01-29-2012, 02:15 PMRed Jhon
For the crash of Battlefield 3 is possible that there is some value in the bios to be retouched, but for the Logitech G19 I do not think a problem of OC. The keyboard must also be recognized in OC!
01-29-2012, 02:20 PMHiVizMan
All things are connected on a motherboard and often the USB port will fall away when a overclock is unstable. Not suggesting that is the case with your system but always worth having an open mind about these things, yeah.
What can happen is after recovering from the crash there is still some corruption of drivers present, when you removed and reseated the USB connector you forced a driver to re-initialise the USB port.
01-29-2012, 02:23 PMUltraNEO*
I find logitech keyboards and mice work better without the actual logitech drivers... perhaps you should try it??
01-29-2012, 02:25 PMRed Jhon
I certainly know that it may be possible ... In your opinion, and 4.6Ghz for SLI GTX580 these parameters are good?
- Vcore 1:34
- VTT 1.15
- 1,070 VTT2
- VCCSA 1.18
- PLL 1.50
- PCH 1.11
01-29-2012, 02:38 PMHiVizMan
That looks all good. I like to have my VTT just a little higher but I do not have a very good IMC on my CPU.
Because of that I prefer to manually set my ram profile timings and voltages in the BIOS and not rely on the XMP, found that by increasing my ram voltage by one notch on each channel stability was greatly improved all round. Also I use tweak 1 for my ram.
In the Dram section do you set to Tweak 1?
With the two cards I would set Gen 2 for the PCIe not needed but I like to leave very little to chance.
As to logitech drivers I have a similar keyboard and mouse from them and I do not use the drivers that come with the product and block Win Auto update from installing them.
01-29-2012, 02:43 PMRed Jhon
Thanks! I brought the VTT to 1.16 .... So I must set VGA GEN2 instead of GEN3? As for the Rams I used the XMP profile and I set the ram MODE1. In MODE 2, the board will not start.
RAM: 1.66 (X2)
01-29-2012, 02:48 PMHiVizMan
I like that.
See how it goes and I hope you post again and this time let it be just to say hello and how it is going without there being any problems.
01-29-2012, 02:57 PMRed Jhon
I set the bios to GEN2 PCI.EXPRESS but again when you restart the keyboard does not work! But the mouse (USB) work well. I rebooted PC and motheboard is blocked to code 99. After 2 minutes the motherboard boot, but appear on the screen "NO KEYBOARD". When I got to Windows, I disconnected and reconnected the keyboard and it works. --_--''