Search:

Seems like the looser I set the timngs, or more voltage I give it, the more unstable it is. Got to the point where it wouldnt boot Windows any more. At 11-13-13 1.625Vdimm and 1.05VCCSA is where I...

I thought about trying 2600, but just didnt. FInally did, and it posts and does 1m, but freezes up after a couple minutes. Working on getting it more stable.

Got a 2x4GB set of Sammy 30nm, and cant get 2400Mhz. Pushed VCCSA to 1.1v from .925v, PCH up to 1.15v, vdimm to 1.625v, set timings really loose to 11-13-13-37-2T, and it still wont post. 2200Mhz...

I bought an 8120 and a 990FXA-UD3, and am going to be returning the board because of a laking BIOS. I was looking at replacing it with the M5A99X-EVO, but want to make sure that there is a BIOS that...

Still got a bit more room to go, but this is where Im at for now with the Ripjaws X PSCs.
1932

Ive only been using 2T so far. I dont expect to get anywhere near the speeds Ive gotten on Intel, but should be able to get something decent out of them considering the PSCs I have do well on here. ...

It seems the 1.6v kit probably went bad in the transition. Tried them in the RII Gene, and they were ok at 1600, but anymore and they would fail quickly, or one of the sticks would drop out at post...

http://s864.photobucket.com/albums/ab207/ctmaudi/PC%20Setups/2011%20AMD%20BD%20Build/BBSE%20Troubleshooting/

1916


Thats my 1.6v kit. I popped my 1.65v kit in, and am at 4 passes now with...

Now that I got pretty much where I wanted to be with the OC, I want to figure out why my Gskill Tridents wont work in this board. They are even on the QVL. At stock settings 1333 9-9-9 they were...

"DRAM Write Recovery Time: Defines the number of clock cycles that must elapse between a memory write operation and a Precharge command. Most DRAM configurations will operate with a setting of 10...

Looks like I missed that one, CPU-Tweaker says 10, Ill double check the BIOS and try 12.

EDIT: Yeah, it was on auto which was 10. Changed to 12, and just booted 280HTT with all 4Gb showing. Going...

I manually set them to 8-9-8-24-6-6-6-8 37-7-3-4-4-2T
At 276HTT 1840Mhz 7-9-7-24 passes prime with 1.6V (1.64V measured)

I was using the 0027 beta BIOS, but switched to the new official one.

Still cant get anywhere usefull with this. 280 bus speed and up shows 2gb unless I use the x5.33 ram multi which sets the ram too low to be worth it. I can also use the x8 ram multi with a lower bus...

275 bus speed is where I was fine. Tried 278, and it showed 2GB. Set the DQS Drive Strength to .75, and now it shows 4GB. Just tried 279, and now its at 2GB again. Manually did all the timings. Only...

What voltage or setting would help? Im already giving more then rated VDIMM for less then rated specs, upped the NB to 1.15, and the CPU/NB is already at 1.325v. Doesnt seem like it should really...

Im using a 1075T and 2x2GB Gskill Ripjawsx 2133 9-11-9 1.6V ram. I can get 4Ghz and 1840 8-9-8-24-2t stable, but when I up it any more, it Windows only shows 2Gb of ram. Says 4GB installed, 1.96GB...

Updated to the 0027 beta BIOS, switched the ram, and think its OK now.

Got my CVF up and running, and it fails prime within seconds at stock clocks. Ive upped the voltage to 1.325Vcore, 1.66Vdimm, 1.2 CPU N/B, 1.2NB. Running a 1075T with turbo off, C1E etc.. off. LLC is...