Search:

All two cards are running at x16 PCIe 3.0.

I'm using R4E motherboard

I have my two 7970 Matrix running CrossFire. When I was running 3D mark 11, at all four graphic test stage, the FPS rate keep jumping beween a high FPS and low FPS ( For example: 50-120 - 60 - 114 -...

No display signal when I install my 7970 on first Pci-e x16 slot of my Maximus V Extreme

When I move the card to 2nd x16 and any x8 slot, it works well. Then I use my old 6970 card, same thing...

Thank you.I use my old card and then use driver sweeper remove all drivers, instal matrix and reinstall drivers. Issue fixed.

I got my new 7970 matrix today. Switched card, reinstalled latest AMD driver and GPU tweak. Everything was fine untill I turn off 2D mode in GPU tweak.

My monitor was going to sleep mode. I reboot...

Havent got decent score yet:(

Oh wait, I didn't coat inside the PCIe slots. How can I do it? remove the slot and coat that area?

Not sure, I see no condensation around after 2 hours of running, but I will try again after few hours.

11358
I use dry ice cooling my 3770K and EVGA GTX680 Classified with EVbolt.
When I was running 3dmark11, there was no problem when CPU 5.4GHZ at 1.675 v, GPU 1388MHz at 1.2375v.

However, if I...

Im going to have my first time subzero OC this weekend (use dry ice), I had read this artical: http://rog.asus.com/109512012/maximu...shamino-andre/
But it was talking about MVF.

So on MVE, can...

Thank you every one. It was the vcore issue, after I increase the vcore, the problem solved.

Same thing happens to me and my friend's M4E. This was my first time using z77 motherboard with 3770k. Hope someone can help my noob question =.=

I am using 3d mark 11 1.0.3. Anytime I overclock my 3770K, during the 3dmark11 physic test, it will show the following error:

Workload work failed with error message: Process exited unexpectedly
...

"CPU LLC: Ultra-High
CPU CURRENT CAP: 180%"

Ultra High and Extreme is for Sub-Zero Cooling, Even I water cooled my motherboard (PCH and VRM), I use a Medium LLC.

8393

NZXT Switch 810, about $180 which is awesome for a high capacity case

Are you using SATA III cable for both SSD? Did you plug them into SATA 6Gs_1 & 2 port (not Asmeda port)

The speed shows that you have been blocked at SATA II speed instead of SATA III

No worry my friend. PLL voltage around 1.8 is pretty common for Sandy-Bridge E.

Enjoy the performence by x79 quad channel ddr3 :cool:

Thank you so much! Just got one!

I heard that, but how can I buy it? any Link?

CPU and VCCSA Load Line Calibration [Medium] with [auto] Curremt Capability are recommanded

You may want increase your VCCSA and VTT voltage a little bit, also more vCore may be needed when you...

G.Skill Ripjaws-X F3-12800cl9d-8GBXL is a dual channel kit

Your platform is x79 which support quad channel. You'd better switch to a quad channel ddr3, for example, G.Skill Ripjaws-Z series

Same here. the qvl haven't been updated for a long time, if G-skill said it works, it will work...

Intel said VTT and VCCSA max are 1.40, sounds good, well I use 1.28 for both @ 2400MHz 10-12-11-31

You can try switch your SSD to non-Asmedia controller port (SATA 6GB 1,2 port) well, I mean to achieve better performence...

I have no idea with the motherboard error code, lets see anyone can...

Are you using RAID or AHCI for you OCZ Vertex. Have you seen the blue screen erro code?