Ocz revo drive x2 install on a asus crosshair V formula mb.

[sickntired]

I was wondering if their is any other members on here that have a OCZ Revo drive x2 installed on the asus crosshair V board? If so, what is best way to go about setting it up as a boot drive? All help would be appreciated, thank you!

[Raja@ASUS]

I was wondering if their is any other members on here that have a OCZ Revo drive x2 installed on the asus crosshair V board? If so, what is best way to go about setting it up as a boot drive? All help would be appreciated, thank you!

The answer you got over at OCZ forums earlier today is correct, no need to second guess it my friend

http://www.ocztechnologyforum.com/fo...board-question

[sickntired]

The answer you got over at OCZ forums earlier today is correct, no need to second guess it my friend

http://www.ocztechnologyforum.com/fo...board-question

That is just it,I did not get a answer , I got a general way to go about it ,hit or miss! All I am looking for is if there is another member on these forums who has the crosshair V motherboard and a ozc revo drive x2 installed and what exactly did they do to install it as a boot drive.

[sickntired]

Ok, now I need to know where is the "WAKE" option in the uefi bios for my crosshair V board that I need to set to on?

[Praz]

You received a specific answer from me at the OCZ forum. Nothing "hit or miss". Anyway the "Wake" option you are looking for is Power On By PME which needs to be set to enabled. Anything else regarding the Revo 3 I will be more than happy to answer in your existing thread at the OCZ forum.

[sickntired]

You received a specific answer from me at the OCZ forum. Nothing "hit or miss". Anyway the "Wake" option you are looking for is Power On By PME which needs to be set to enabled. Anything else regarding the Revo 3 I will be more than happy to answer in your existing thread at the OCZ forum.

Ok,I was cornfused as to thinking that "WAKE" and "PME" was two separate entity's! sorry for wasting your time!

[theoneandonlymrk]

You received a specific answer from me at the OCZ forum. Nothing "hit or miss". Anyway the "Wake" option you are looking for is Power On By PME which needs to be set to enabled. Anything else regarding the Revo 3 I will be more than happy to answer in your existing thread at the OCZ forum.

OP said revo x2 not 3 ,does that matter

I have a hang on

quad phenomII 960T @ 4050Mhz waterblocked
Crosshair V formula NB @ 3150 waterblocked
mushkin 2133 ram @ 1800 9,9,9,24 waterblocked
5870 ,5850 xfired @ 1000 core mem 1200 waterblocked
Revo x2 120g ssd OS origin <<<<<<<<<< OS
Wd cav blu 250 x2 raid 0 Programs
Wd cav green 1Tb backup
320+240+120 rads all push pull (low rpm) single custom loop and Res
Corsair 850TX psu
Kandalf custom modded case


I did not alter PMe or wake on anything, i just plugged it in and booted and installed windows, however windows (setup) couldnt see the drive and i had to install the revo's driver ,from the disk i got with it(ive since updated the driver) then windows setup could see the drive and the install went without hicup.

on a similar note though ive tried moveing it around the slots since with OS on and without a reinstall and its never listed in the bios( under the Pciex tab) the board sees both gfx but never the ssd, i recently reflashed the ssd with the latest bios(which joy of joys didnt wipe its boot partition) but its still not seen in bios, however windows sees it once loaded and it boots fine , the sytem volume is on it.

[HiVizMan]

Thank you Praz for responding, and hope you are feeling a bit better mate.

[Praz]

Thank you Praz for responding, and hope you are feeling a bit better mate.

Finally getting over this stuff I think. I guess this is payback for never being sick.