Rampage IV Gene, No Boot debug code 00 and cpu_led error

[cloudalmasai]

Hi, I today got my new r4g, paired with a i7 3820 and 4x2gb samsung 30nm green ram, I put together everything follow the manual, but got the error put in the title, what I can do before tried to RMA the board? thank. Sorry for my bad english

[Arne Saknussemm]

Hi cloudalmasai. Can you give a few more details: Exact RAM kit, bios version ssd hdd.

First things first check all your cables are connected properly. That you have the correct SATA cable for ssd or hdd and correct port etc. Maybe reseat carefully the cpu and while you do that check all the pins in the socket are lined up perfectly.

[cloudalmasai]

Hi cloudalmasai. Can you give a few more details: Exact RAM kit, bios version ssd hdd.

First things first check all your cables are connected properly. That you have the correct SATA cable for ssd or hdd and correct port etc. Maybe reseat carefully the cpu and while you do that check all the pins in the socket are lined up perfectly.

Hi thanks for reply, the cable where revised several times, the cpu reseated four times, tried with diferent bios file an cleare cmos, nothing worked. Now I doing a full clear cmos for 12 horus, maybe thats work.

[Arne Saknussemm]

Hmm OK sounds like you have all that under control.....Is that RAM a quad channel kit or do you have 2 kits there....this might give problems..

[cloudalmasai]

Hmm OK sounds like you have all that under control.....Is that RAM a quad channel kit or do you have 2 kits there....this might give problems..

Is 2 kits of 2x2gb samsung 30nm green ddr3, but I have tried one in single channel and is the same

[Zka17]

What is your BIOS version? You may have the M1 revision of the 3820 - it is supported only with later BIOS versions...

[Arne Saknussemm]

You have working fan conected to CPU fan header? Working GPU? Scratchin gmy head here....really though if you've checked all this stuff if it comes out of long clear cmos the same I'd RMA it. Just check bios is up to date and try the CPU in a nother board if you have the possibility.

[cloudalmasai]

What is your BIOS version? You may have the M1 revision of the 3820 - it is supported only with later BIOS versions...

Maybe you have rigth, but I dont know how to check my cpu revision, but I flash the latest bios found in the r4g download page, if I remember well was the 1305, but nothing changed.

You have working fan conected to CPU fan header? Working GPU? Scratchin gmy head here....really though if you've checked all this stuff if it comes out of long clear cmos the same I'd RMA it. Just check bios is up to date and try the CPU in a nother board if you have the possibility.

Yes the cpu fans is working fine, the gpu used is from my actual computer and when putting back in it, working without a problem, I have another ram ddr3 ram laying around and will tried swapping around the samsung ones. The system only star for a few seconds showing the stuff already said and then power of by itself . Today at 2 pm will tried again, now here in venezuela is 9 am.

PD= at the firts boot up the board start to show diferent codes in the debug led, that was only wthit the cpu, fans, rams and psu installed, the last cod in the led was A2 if remembered well, but then installed the gpu and no longer boot showwing cpu error led and code 00 in the debug. Then deinstalling the gpu and testing in the other pc and still working but the board not wanna boot again.

The GPU is an ATI HD4670, for if this matter

[Arne Saknussemm]

Yes 1305 is the latest. M1 was suported from 1103...you are ok on that.

Did you install the graphics card in slot 1?

Did you try pressing the "Go" button before post to start the mem ok function?

[cloudalmasai]

Yes 1305 is the latest. M1 was suported from 1103...you are ok on that.

Did you install the graphics card in slot 1?

Did you try pressing the "Go" button before post to start the mem ok function?

Yes the grafic card was put in the first slot, already tried pushing the Go buttons, but I dont know if was done correctly,
is only pushing once or for a certain period of time?