ASUS Crosshair V Formula BIOS Guide - Overclocking

[IronMikeAce]

Please help me find the setting for VID voltage on a CH5F ?
Thanks

I dont know why the pic didn't show. I will provide link. Here is bios SS.

http://imageshack.us/f/221/111203185210e.png/

[IronMikeAce]

UEFI build 9920 is linked in this forum.

Have you tried the new 9921 bios? Is there a later bios update than 9921?

Also, I have a water cooler on my cpu and there is not much air flow around cpu. I have a temp probe in the VRM and NB heatsink (slid down the red heat pipe that runs through heatsink. Is this an optimal place to put it or is there a better place I can put it for more accurate readings? The temp shown now never go over 50C at max load. CPU overclocked to 4.9Ghz and CPU/NB overclocked to 2500MHz, HT Link overclocked to 2750MHz and RAM overclocked to 2000MHz from 1866MHz. I also have temp probe in ram stick which stays under 38C. There is no way for me to put a small fan over VRM / NB because of water bock and thick radiator and another fan attached. Is there any way you could think taht I could get a more accurate reading of VRM and NB and is there anything you can think of a way to cool VRM.

Video link of my system. Let me know what you think.



Any other advise would be greatly appreciated too.

Thank you for the help.

[ahellblazer]

Hey Raja,

Man i have this crosshair Formula V mobo, it is shoowing me the update error, when ever i switch on my PC, it shows me the Bios and then it says to press F1 as Overclockin has failed, then when i go to BIOS setup it shows the error msg of "Input Error" then when i press ok it hangs, is there any way of going to default setting. This only happened after the update .

[Raja@ASUS]

Use only one memory module and clear CMOS. If that does not help contact ASUS Support in India.

[ahellblazer]

Actually the error is "Input Range error". I also tried to remove the CMOS battery and then again restarted the PC but still the same issue. should i remove the CMOS and then press reset or i did it right !!!

[jcfsusmc]

When are you planning to update the OC Guide now that 9921/1003 bioses have numerous additions, options, and fixes?

Or have I missed something?

[Reko]

i just got a fresh crosshair v and a 8150 upgraded to the latest bios..... but i cant seem to change the cpu ratio like in the pictures....

[Granger]

hax0r,

If you want to go any further with a stock cooler, you are likely to fry your proc, I'm running practically the same system as you, with a good aftermarket cooler and the temps go pretty wild on a high load.

[tawak]

hi can you help me overclock my cpu
can i have your recipe
auto overclock stuck at 3.5ghz(shame)
thanks!

crosshire v formula
phenom ii x6 1090T/v6gt
hd6970
8gb gskill ripjaw
2 tb hdd

[Black Flag]

New user here and first time I bought an Asus motherboard.

I have my 1090T overclocked and stable to 3,8 GHz, 2,8 GHz NB Frequency and DDR3 to 1600MHz (9-9-9-27) with stock voltages, except for CPU/NB which I'm using 1,27 V. I cannot have my cpu stable with 1,4875 V at 4,2 GHz even with LLC off. Even with good airflow with cosmos pure and Scythe Mugen Rev 3. installed, the CPU temperature, not core temperature, reaches 70 - 72 degrees of Celcius and the system (Win7x64 SP1 Ultimate) gives me BSOD. Motherboard has latest bios.