z490 ASUS-Apex Boot Issue

So i got around to installing my new pc , here are specs to see what to determine the issue might be.
i9-10900k
2080ti EVGA FTW3 Hybrid
4500MHZ Team Group DDR4
2 m.2 Drives
-1 Corsair
-1 Samsung Evo
1200W Psu
Asus Apex MB
Win 10 Pro

I got around to making a video of the issue UPDATED* 6/14/2020

https://www.youtube.com/watch?v=OWsmelm3ofg


So upon boot somtimes my screen just sits black and i have to restart the pc in order to get somewhere
Sometimes i see the rog logo and then gos black again
Sometimes i see the rog logo and 10-15 seconds later i see the Windows circles going in a loop like its loading.
This is about 45 seconds in , dont get me wrong that is not long , but with the hardware i purchased i feel something is wrong.
Once i login everything seems fine , its just when i shutdown and come back like 10 hours later and try to boot i get these weird boot up process , when it should be start forward and fast bootup.

-Also just rebooted right now and it reboots under 5 seconds but when i login to my account the nividia driver is not registered .. then i hear it connect and says G-SYNC Available .

Any info would be appreciated

bump

1. Check your display cable if its plugged correctly, firmly.

Or:

2. This might be because of the ram. Try booting with no XMP and it will prolly work just fine.
I had a similar issue with my ram, same black screen, or lagging loading dots, etc. The ram was not stable at that freq because of a setting that the board would set really bad. It was the rtt_park value which i had to set at 48 clocks in order to get my ram stable on both channels. You should try this and lower vccio and vccsa that your mb is setting at like 1.25 and add more on vccsa if you get errors or crashes with the stock xmp profile. The "park" setting for both ram channels is located under dram timings control->skew control on my z390. Change it for both channels: CHA1 CHA0, its something like odt rtt_park, set if for both channels at 48 and it should be ok.

Quote:

---

Originally Posted by qlfenv

1. Check your display cable if its plugged correctly, firmly.

Or:

2. This might be because of the ram. Try booting with no XMP and it will prolly work just fine.
I had a similar issue with my ram, same black screen, or lagging loading dots, etc. The ram was not stable at that freq because of a setting that the board would set really bad. It was the rtt_park value which i had to set at 48 clocks in order to get my ram stable on both channels. You should try this and lower vccio and vccsa that your mb is setting at like 1.25 and add more on vccsa if you get errors or crashes with the stock xmp profile. The "park" setting for both ram channels is located under dram timings control->skew control on my z390. Change it for both channels: CHA1 CHA0, its something like odt rtt_park, set if for both channels at 48 and it should be ok.

---

whoops i meant my ram is actually rated for 4500mhz but its defaulted right now at 2400mhz

bump still have issue... actually ran overclocking and the pc runs perfect!! got my ram to 4500mhz and can play game flawlessly , and cpu 5.2ghz... everything runs fine on the pc.. its just the boot. It seems to lock up when trying to get the display driver to come online it seems.

I think there are bios issues right now. I can't get my Z490 Apex to shut down with windows. It boots perfectly but won't shut down. I have to turn off my powersupply at night when I go to bed.

I got around to making a video

https://www.youtube.com/watch?v=OWsmelm3ofg

lol I have the opposite issue :) I am still thinking you should clear cmos and try it not overclocked first to get all the drivers loaded and hardware recognized properly first. I think somthing else might be happening here. .. clear cmos and boot in standard mode. I guess you can shut the pc down correctly with windows shutdown right ?

Quote:

---

Originally Posted by 1mluer

lol I have the opposite issue :) I am still thinking you should clear cmos and try it not overclocked first to get all the drivers loaded and hardware recognized properly first. I think somthing else might be happening here. .. clear cmos and boot in standard mode. I guess you can shut the pc down correctly with windows shutdown right ?

---

it did this when nothing was overclocked .. i wanted to test the overclocking and everything works fine. it boots faster with the Optimized overclocked settings , oddly lol. Yes i can restart shutdown and everything works fine. Its just the Display does not come on sometimes then i have to press start button on pc case to restart it and then it will go into what i show in the video

I think I recreated your issue. I went to pch storage configuration and put Sata Interupt Setting on "SMI" when I did that it took forever to boot. When I changed it to "SMIX" or "Legacy" it allowed normal booting.. check that.. I am trying to troubleshoot why I can't shut down my system but your problem seemed easier to me to fix.. check it out.

Not to mention I seen your video card was PCI X8 setting make sure you have all the PCI settings to Gen3

Mine is already on Smix .. gonna try a few things tho

Ok actually u have to enable Intel Rapid Storage memory ..
Then it gives you an option for Sata Interrupt .. it was already on smixed..

That looks like options for Raid Control for the m.2 drives .. not sure how that would relate to my boot??
I took pictures of why i couldnt find it initially

pictures are to show you have to go into SATA Mode Selection in order to get that SATA interrupt option..

yep looks like you are right.. If I use msi on my raid setup it takes ages to boot.. I use msix or legacy it boots correctly. Well I gave it a try. I will continue to look at this along with my problem. I still have a suspicion it's bios related in some way at least for my problem.

By the way, did you mount your ssd's on the dimm.2 or onboard. On board if I read it right shares the pci express slot with your graphics card making it 8X not 16X.

Just made this video of my issue :)

https://youtu.be/j9SaGFwFxDI

Quote:

---

Originally Posted by 1mluer

yep looks like you are right.. If I use msi on my raid setup it takes ages to boot.. I use msix or legacy it boots correctly. Well I gave it a try. I will continue to look at this along with my problem. I still have a suspicion it's bios related in some way at least for my problem.

By the way, did you mount your ssd's on the dimm.2 or onboard. On board if I read it right shares the pci express slot with your graphics card making it 8X not 16X.

Just made this video of my issue :)

https://youtu.be/j9SaGFwFxDI

---

For your issue and both mine i think im going to just put my PC in sleep mode instead of shutdown. That may be a temporary fix.
I have my EVO m.2 in the RAM m.2 slot and i have a corsair on the board right above the gfx card. I was thinking about that when i placed the corsair m.2 above the gfx card and hope that my gfx card get x16 .. ill have to try taking it out. Only reason why i put it above my gfx card is because it has heat sink on it and cant go into the Ram m.2

Your pc atleast boosts how it should.

I also found multiple issues with booting etc with the z490 platform . Im thinking they will release a new bios or patch to get the bugs fixed. This is common with new technology

Update*** Even after taking out the corsair m.2 that is above the gfx card.. The boot time still elapsed to 1-2 mins, I did a 3 trial run. The first two boots were 1-2mins BUT the nividia driver was registered. On the third attempt no nividia driver. Therefore ruling out if the corsair is interfering with the x16 needed for the gfx card. Ironically i put the m.2 back in , and it booted within 10 seconds and nividia driver registered. So im back to pulling my hair out Lol! Hopefully it stays that way..

Quote:

---

Originally Posted by nosam1g

I got around to making a video

https://www.youtube.com/watch?v=OWsmelm3ofg

---

To me it looks like a memory training issue or some kind of boot issue/instability. Do you always get the disk check like in your video?

I would try MRC FAST Boot Disable and MCH FULL Check Enable and see what happens.

Quote:

---

Originally Posted by 1mluer

yep looks like you are right.. If I use msi on my raid setup it takes ages to boot.. I use msix or legacy it boots correctly. Well I gave it a try. I will continue to look at this along with my problem. I still have a suspicion it's bios related in some way at least for my problem.

By the way, did you mount your ssd's on the dimm.2 or onboard. On board if I read it right shares the pci express slot with your graphics card making it 8X not 16X.

Just made this video of my issue :)

https://youtu.be/j9SaGFwFxDI

---

Under Advanced, ON Board Devices, LED Lighting have you tried setting it to Stealth Mode when Sleep/Soft Off?

It is a good practice to list the current bios you are using to help identify issues. I have tried 403, 062, 607 and I haven't had any issue with those on the Apex Xll.

Also listing all bios settings can help identify issues. When in the bios with a USB formatted to FAT 32 go to Tool, Load/Save Profile, CTR+F2. Then you can post the settings and someone might be able to identify something.

Quote:

---

Originally Posted by bscool

To me it looks like a memory training issue or some kind of boot issue/instability. Do you always get the disk check like in your video?

I would try MRC FAST Boot Disable and MCH FULL Check Enable and see what happens.

---

No the disk check came after i did a Microsoft update lol . i have it turned off now.
If it was boot instability it would let me know in POST and it would not go any further. I really think its the GFX card , because the spindle loading i think it is trying to find the gfx driver before logging in. As you saw in the video it does then pick it up after i login.

Ill try ur suggestions once i get back from work. Ill try to take pictures of a lot of the tabs.. What are the main things to check .. I have built a few pcs and i have never had to change bios settings after i installed a pc. my bios is 607

When in the bios with a USB formatted to FAT 32 go to Tool, Load/Save Profile, CTR+F2
Can you explain how to do this .

Quote:

---

Originally Posted by nosam1g

No the disk check came after i did a Microsoft update lol . i have it turned off now.
If it was boot instability it would let me know in POST and it would not go any further. I really think its the GFX card , because the spindle loading i think it is trying to find the gfx driver before logging in. As you saw in the video it does then pick it up after i login.

Ill try ur suggestions once i get back from work. Ill try to take pictures of a lot of the tabs.. What are the main things to check .. I have built a few pcs and i have never had to change bios settings after i installed a pc. my bios is 607

When in the bios with a USB formatted to FAT 32 go to Tool, Load/Save Profile, CTR+F2
Can you explain how to do this .

---

You might be right, but if it was the GPU driver how would overclocking the ram fix it? Or maybe I misunderstood.

As for how to save the bios settings I don't know how to explain it better. You have a USB stick and follow those steps and it will save them to the USB as a txt file then you can post them. But it is not a big deal. Try the MRC and MCH setting and see what happens.

When you say you overclocked the ram did you just enable XMP or manually change timings and voltages? XMP over 4400 put the voltages super high. ON my APEX Xll VCCIO is 1.46 and VCSSA is 1.672 just setting XMP for the higher frequency's above 4400. That might be ok long term but I wouldn't do it.

Also when getting over 4000-4133 just enabling XMP doesn't always work. Usually I have needed to go in and make changes. Pushing 4400+ using just XMP is asking a lot. The motherboard manufacturers are not there yet from what I can see.

The file will look like this when you open it when back in WIndows.

Ai Overclock Tuner [XMP II]
XMP [XMP DDR4-4807 18-22-22-42-1.50V]
BCLK Frequency [100.0000]
PCIE Frequency [100.0000]
ASUS MultiCore Enhancement [Enabled – Remove All limits]
SVID Behavior [Auto]
AVX Instruction Core Ratio Negative Offset [0]
CPU Core Ratio [Sync All Cores]
ALL-Core Ratio Limit [50]
BCLK Frequency : DRAM Frequency Ratio [Auto]
DRAM Odd Ratio Mode [Enabled]
DRAM Frequency [DDR4-4600MHz]
Xtreme Tweaking [Disabled]
CPU SVID Support [Auto]
Maximus Tweak [Mode 1]
DRAM CAS# Latency [17]
DRAM RAS# to CAS# Delay [18]
DRAM RAS# ACT Time [38]
DRAM Command Rate [2N]
DRAM RAS# to RAS# Delay L [6]
DRAM RAS# to RAS# Delay S [4]
DRAM REF Cycle Time [350]
DRAM REF Cycle Time 2 [Auto]
DRAM REF Cycle Time 4 [Auto]
DRAM Refresh Interval [65535]
DRAM WRITE Recovery Time [12]
DRAM READ to PRE Time [8]
DRAM FOUR ACT WIN Time [24]
DRAM WRITE to READ Delay [5]
DRAM WRITE to READ Delay L [5]
DRAM WRITE to READ Delay S [5]
DRAM CKE Minimum Pulse Width [6]
DRAM Write Latency [16]
ODT RTT WR (CHA) [Auto]
ODT RTT PARK (CHA) [Auto]
ODT RTT NOM (CHA) [Auto]
ODT RTT WR (CHB) [Auto]
ODT RTT PARK (CHB) [Auto]
ODT RTT NOM (CHB) [Auto]
ODT_READ_DURATION [Auto]
ODT_READ_DELAY [Auto]
ODT_WRITE_DURATION [Auto]
ODT_WRITE_DELAY [Auto]
Data Rising Slope [Auto]
Data Rising Slope Offset [Auto]
Cmd Rising Slope [Auto]
Cmd Rising Slope Offset [Auto]
Ctl Rising Slope [Auto]
Ctl Rising Slope Offset [Auto]
Clk Rising Slope [Auto]
Clk Rising Slope Offset [Auto]
Data Falling Slope [Auto]
Data Falling Slope Offset [Auto]
Cmd Falling Slope [Auto]
Cmd Falling Slope Offset [Auto]
Ctl Falling Slope [Auto]
Ctl Falling Slope Offset [Auto]
Clk Falling Slope [Auto]
Clk Falling Slope Offset [Auto]
DRAM RTL INIT value [Auto]
DRAM IOL INIT value(CHA) [Auto]
DRAM IOL INIT value(CHB) [Auto]
DRAM RTL (CHA DIMM0 Rank0) [63]
DRAM RTL (CHA DIMM0 Rank1) [Auto]
DRAM RTL (CHA DIMM1 Rank0) [Auto]
DRAM RTL (CHA DIMM1 Rank1) [Auto]
DRAM RTL (CHB DIMM0 Rank0) [63]
DRAM RTL (CHB DIMM0 Rank1) [Auto]
DRAM RTL (CHB DIMM1 Rank0) [Auto]
DRAM RTL (CHB DIMM1 Rank1) [Auto]
DRAM IOL (CHA DIMM0 Rank0) [7]
DRAM IOL (CHA DIMM0 Rank1) [4]
DRAM IOL (CHA DIMM1 Rank0) [4]
DRAM IOL (CHA DIMM1 Rank1) [4]
DRAM IOL (CHB DIMM0 Rank0) [7]
DRAM IOL (CHB DIMM0 Rank1) [4]
DRAM IOL (CHB DIMM1 Rank0) [4]
DRAM IOL (CHB DIMM1 Rank1) [4]
CHA IO_Latency_offset [21]
CHB IO_Latency_offset [21]
CHA RFR delay [14]
CHB RFR delay [14]
Early Command Training [Auto]
SenseAmp Offset Training [Enabled]
Early ReadMPR Timing Centering 2D [Enabled]
Read MPR Training [Enabled]
Receive Enable Training [Enabled]
Jedec Write Leveling [Enabled]
LPDDR4 Write DQ DQS Retraining [Enabled]
Early Write Time Centering 2D [Auto]
Early Read Time Centering 2D [Auto]
Write Timing Centering 1D [Enabled]
Write Voltage Centering 1D [Auto]
Read Timing Centering 1D [Auto]
Dimm ODT Training* [Auto]
DIMM RON Training* [Auto]
Write Drive Strength/Equalization 2D* [Auto]
Write Slew Rate Training* [Auto]
Read ODT Training* [Auto]
Read Equalization Training* [Auto]
Read Amplifier Training* [Auto]
Write Timing Centering 2D [Auto]
Read Timing Centering 2D [Auto]
Command Voltage Centering [Auto]
Write Voltage Centering 2D [Auto]
Read Voltage Centering 2D [Auto]
Late Command Training [Auto]
Round Trip Latency [Auto]
Turn Around Timing Training [Disabled]
Rank Margin Tool [Auto]
Margin Check Limit [Disabled]
Memory Test [Disabled]
DIMM SPD Alias Test [Auto]
Receive Enable Centering 1D [Auto]
Retrain Margin Check [Disabled]
CMD Drive Strength and Tx Equalization [Auto]
CMD Slew Rate Training [Auto]
Write Drive Strength Up/Dn independently [Disabled]
tRDRD_sg_Training [7]
tRDRD_sg_Runtime [6]
tRDRD_dg [4]
tRDWR_sg [12]
tRDWR_dg [12]
tWRWR_sg [6]
tWRWR_dg [4]
tWRRD_sg [31]
tWRRD_dg [26]
tRDRD_dr [6]
tRDRD_dd [6]
tRDWR_dr [12]
tRDWR_dd [12]
tWRWR_dr [5]
tWRWR_dd [5]
tWRRD_dr [4]
tWRRD_dd [4]
TWRPRE [Auto]
TRDPRE [Auto]
tREFIX9 [127]
OREF_RI [64]
MRC Fast Boot [Disabled]
Delay after Train [Disabled]
DRAM CLK Period [Auto]
Memory Scrambler [Enabled]
Channel A DIMM Control [Enable both DIMMs]
Channel B DIMM Control [Enable both DIMMs]
Trace Centering [Disabled]
MCH Full Check [Enabled]
Mem Over Clock Fail Count [Auto]
Training Profile [Auto]
DLLBwEn [Auto]
Legacy Mode [Disabled]
SPD Write Disable [TRUE]
XTU Setting [Auto]
Voltage Monitor [Die Sense]
CPU Load-line Calibration [Level 4:Recommended for OC]
Synch ACDC Loadline with VRM Loadline [Disabled]
CPU Current Capability [Auto]
CPU VRM Switching Frequency [Auto]
VRM Spread Spectrum [Auto]
CPU Power Duty Control [T.Probe]
CPU Power Phase Control [Auto]
CPU Power Thermal Control [130]
CPU VRM Thermal Control [Auto]
DRAM Current Capability [100%]
DRAM Switching Frequency [Auto]
CPU Core/Cache Boot Voltage [Auto]
DMI Boot Voltage [Auto]
CPU System Agent Boot Voltage [Auto]
CPU VCCIO Boot Voltage [Auto]
PLL Termination Boot voltage [Auto]
CPU Standby Boot Voltage [Auto]
Maximum CPU Core Temperature [Auto]
CPU Core/Cache Current Limit Max. [Auto]
Long Duration Package Power Limit [Auto]
Package Power Time Window [Auto]
Short Duration Package Power Limit [Auto]
IA AC Load Line [Auto]
IA DC Load Line [Auto]
TVB Voltage Optimizations [Auto]
TVB Ratio Clipping [Auto]
V-Max Stress [Auto]
Offset Mode Sign 1 [+]
V/F Point 1 Offset [Auto]
Offset Mode Sign 2 [+]
V/F Point 2 Offset [Auto]
Offset Mode Sign 3 [+]
V/F Point 3 Offset [Auto]
Offset Mode Sign 4 [+]
V/F Point 4 Offset [Auto]
Offset Mode Sign 5 [+]
V/F Point 5 Offset [Auto]
Offset Mode Sign 6 [+]
V/F Point 6 Offset [Auto]
Offset Mode Sign 7 [+]
V/F Point 7 Offset [Auto]
Offset Mode Sign 8 [+]
V/F Point 8 Offset [Auto]
Realtime Memory Timing [Enabled]
FCLK Frequency for Early Power On [Auto]
Initial BCLK Frequency [Auto]
BCLK Amplitude [Auto]
BCLK Slew Rate [Auto]
BCLK Spread Spectrum [Auto]
BCLK Frequency Slew Rate [Auto]
PCIE/DMI Amplitude [Auto]
PCIE/DMI Spread Spectrum [Auto]
PCIE/DMI Frequency Slew Rate [Auto]
PCIE/DMI Slew Rate [Auto]
Cold Boot PCIE Frequency [Auto]
DRAM VTT Voltage [Auto]
VPPDDR Voltage [Auto]
DMI Voltage [Auto]
Internal PLL Voltage [Auto]
GT PLL Voltage [Auto]
Ring PLL Voltage [Auto]
System Agent PLL Voltage [Auto]
Memory Controller PLL Voltage [Auto]
CPU Standby Voltage [Auto]
PLL Bandwidth [Auto]
Eventual DRAM Voltage [Auto]
Eventual CPU Standby Voltage [Auto]
Eventual PLL Termination Voltage [Auto]
Eventual CPU VCCIO Voltage [Auto]
Eventual DMI Voltage [Auto]
System Agent Bandgap Workaround [Auto]
Package Temperature Threshold [Auto]
Regulate Frequency by above Threshold [Auto]
Cooler Efficiency Customize [Keep Training]
Cooler Re-evaluation Algorithm [Normal]
Optimism Scale [100]
Ring Down Bin [Auto]
Min. CPU Cache Ratio [48]
Max CPU Cache Ratio [48]
BCLK Aware Adaptive Voltage [Enabled]
CPU Core/Cache Voltage [Manual Mode]
- CPU Core Voltage Override [1.450]
DRAM Voltage [1.55000]
CPU VCCIO Voltage [1.42000]
CPU System Agent Voltage [1.52000]
PLL Termination Voltage [Auto]
PCH Core Voltage [Auto]
DRAM CTRL REF Voltage on CHA [Auto]
DRAM CTRL REF Voltage on CHB [Auto]
DRAM DATA REF Voltage on CHA DIMM0 Rank0 BL0 [Auto]
DRAM DATA REF Voltage on CHA DIMM0 Rank0 BL1 [Auto]
DRAM DATA REF Voltage on CHA DIMM0 Rank0 BL2 [Auto]
DRAM DATA REF Voltage on CHA DIMM0 Rank0 BL3 [Auto]
DRAM DATA REF Voltage on CHA DIMM0 Rank0 BL4 [Auto]
DRAM DATA REF Voltage on CHA DIMM0 Rank0 BL5 [Auto]
DRAM DATA REF Voltage on CHA DIMM0 Rank0 BL6 [Auto]
DRAM DATA REF Voltage on CHA DIMM0 Rank0 BL7 [Auto]
DRAM DATA REF Voltage on CHA DIMM0 Rank1 BL0 [Auto]
DRAM DATA REF Voltage on CHA DIMM0 Rank1 BL1 [Auto]
DRAM DATA REF Voltage on CHA DIMM0 Rank1 BL2 [Auto]
DRAM DATA REF Voltage on CHA DIMM0 Rank1 BL3 [Auto]
DRAM DATA REF Voltage on CHA DIMM0 Rank1 BL4 [Auto]
DRAM DATA REF Voltage on CHA DIMM0 Rank1 BL5 [Auto]
DRAM DATA REF Voltage on CHA DIMM0 Rank1 BL6 [Auto]
DRAM DATA REF Voltage on CHA DIMM0 Rank1 BL7 [Auto]
DRAM DATA REF Voltage on CHA DIMM1 Rank0 BL0 [Auto]
DRAM DATA REF Voltage on CHA DIMM1 Rank0 BL1 [Auto]
DRAM DATA REF Voltage on CHA DIMM1 Rank0 BL2 [Auto]
DRAM DATA REF Voltage on CHA DIMM1 Rank0 BL3 [Auto]
DRAM DATA REF Voltage on CHA DIMM1 Rank0 BL4 [Auto]
DRAM DATA REF Voltage on CHA DIMM1 Rank0 BL5 [Auto]
DRAM DATA REF Voltage on CHA DIMM1 Rank0 BL6 [Auto]
DRAM DATA REF Voltage on CHA DIMM1 Rank0 BL7 [Auto]
DRAM DATA REF Voltage on CHA DIMM1 Rank1 BL0 [Auto]
DRAM DATA REF Voltage on CHA DIMM1 Rank1 BL1 [Auto]
DRAM DATA REF Voltage on CHA DIMM1 Rank1 BL2 [Auto]
DRAM DATA REF Voltage on CHA DIMM1 Rank1 BL3 [Auto]
DRAM DATA REF Voltage on CHA DIMM1 Rank1 BL4 [Auto]
DRAM DATA REF Voltage on CHA DIMM1 Rank1 BL5 [Auto]
DRAM DATA REF Voltage on CHA DIMM1 Rank1 BL6 [Auto]
DRAM DATA REF Voltage on CHA DIMM1 Rank1 BL7 [Auto]
DRAM DATA REF Voltage on CHB DIMM0 Rank0 BL0 [Auto]
DRAM DATA REF Voltage on CHB DIMM0 Rank0 BL1 [Auto]
DRAM DATA REF Voltage on CHB DIMM0 Rank0 BL2 [Auto]
DRAM DATA REF Voltage on CHB DIMM0 Rank0 BL3 [Auto]
DRAM DATA REF Voltage on CHB DIMM0 Rank0 BL4 [Auto]
DRAM DATA REF Voltage on CHB DIMM0 Rank0 BL5 [Auto]
DRAM DATA REF Voltage on CHB DIMM0 Rank0 BL6 [Auto]
DRAM DATA REF Voltage on CHB DIMM0 Rank0 BL7 [Auto]
DRAM DATA REF Voltage on CHB DIMM0 Rank1 BL0 [Auto]
DRAM DATA REF Voltage on CHB DIMM0 Rank1 BL1 [Auto]
DRAM DATA REF Voltage on CHB DIMM0 Rank1 BL2 [Auto]
DRAM DATA REF Voltage on CHB DIMM0 Rank1 BL3 [Auto]
DRAM DATA REF Voltage on CHB DIMM0 Rank1 BL4 [Auto]
DRAM DATA REF Voltage on CHB DIMM0 Rank1 BL5 [Auto]
DRAM DATA REF Voltage on CHB DIMM0 Rank1 BL6 [Auto]
DRAM DATA REF Voltage on CHB DIMM0 Rank1 BL7 [Auto]
DRAM DATA REF Voltage on CHB DIMM1 Rank0 BL0 [Auto]
DRAM DATA REF Voltage on CHB DIMM1 Rank0 BL1 [Auto]
DRAM DATA REF Voltage on CHB DIMM1 Rank0 BL2 [Auto]
DRAM DATA REF Voltage on CHB DIMM1 Rank0 BL3 [Auto]
DRAM DATA REF Voltage on CHB DIMM1 Rank0 BL4 [Auto]
DRAM DATA REF Voltage on CHB DIMM1 Rank0 BL5 [Auto]
DRAM DATA REF Voltage on CHB DIMM1 Rank0 BL6 [Auto]
DRAM DATA REF Voltage on CHB DIMM1 Rank0 BL7 [Auto]
DRAM DATA REF Voltage on CHB DIMM1 Rank1 BL0 [Auto]
DRAM DATA REF Voltage on CHB DIMM1 Rank1 BL1 [Auto]
DRAM DATA REF Voltage on CHB DIMM1 Rank1 BL2 [Auto]
DRAM DATA REF Voltage on CHB DIMM1 Rank1 BL3 [Auto]
DRAM DATA REF Voltage on CHB DIMM1 Rank1 BL4 [Auto]
DRAM DATA REF Voltage on CHB DIMM1 Rank1 BL5 [Auto]
DRAM DATA REF Voltage on CHB DIMM1 Rank1 BL6 [Auto]
DRAM DATA REF Voltage on CHB DIMM1 Rank1 BL7 [Auto]
PCI Express Native Power Management [Disabled]
DMI Link ASPM Control [Disabled]
ASPM [Disabled]
L1 Substates [Disabled]
PCI Express Clock Gating [Disabled]
DMI Link ASPM Control [Disabled]
PEG - ASPM [Disabled]
Software Guard Extensions (SGX) [Disabled]
Tcc Offset Time Window [Auto]
Hardware Prefetcher [Enabled]
Adjacent Cache Line Prefetch [Enabled]
Intel (VMX) Virtualization Technology [Disabled]
Active Processor Cores [All]
Hyper-Threading [Enabled]
Hyper-Threading of Core 0 [Enabled]
Hyper-Threading of Core 1 [Enabled]
Hyper-Threading of Core 2 [Enabled]
Hyper-Threading of Core 3 [Enabled]
Hyper-Threading of Core 4 [Enabled]
Hyper-Threading of Core 5 [Enabled]
Hyper-Threading of Core 6 [Enabled]
Hyper-Threading of Core 7 [Enabled]
MonitorMWait [Enabled]
Boot performance mode [Auto]
Intel(R) SpeedStep(tm) [Disabled]
Intel(R) Speed Shift Technology [Disabled]
Turbo Mode [Enabled]
CPU C-states [Disabled]
Thermal Monitor [Enabled]
Dual Tau Boost [Disabled]
VT-d [Disabled]
Above 4G Decoding [Enabled]
Memory Remap [Enabled]
PCIEX16_1 Link Speed [Auto]
PCIEX16_2 Link Speed [Auto]
PCIe Speed [Auto]
SATA Controller(s) [Disabled]
PTT [Disable]
Discrete Thunderbolt(TM) Support [Disabled]
SR-IOV Support [Disabled]
Legacy USB Support [Disabled]
XHCI Hand-off [Disabled]
U32G2_1 [Enabled]
U32G2_2 [Enabled]
U32G2_3 [Enabled]
U32G2_4 [Enabled]
U32G1_7 [Enabled]
U32G1_8 [Enabled]
U32G1_E1 [Enabled]
U32G1_E2 [Enabled]
U32G1_E3 [Enabled]
U32G1_E4 [Enabled]
U32G1_9 [Enabled]
SP_USB11 [Enabled]
U32G2_5 [Enabled]
U32G2_C6 [Enabled]
Network Stack [Disabled]
Hyper M.2X16 [Disabled]
HD Audio [Enabled]
Intel LAN [Enabled]
USB power delivery in Soft Off state (S5) [Disabled]
Connectivity mode (Wi-Fi & Bluetooth) [Disabled]
When system is in working state [Stealth Mode]
M.2_1 Configuration [Auto]
DIMM2_1 Configuration [Auto]
DIMM2_2 Configuration [Auto]
U32G2_C6 Type C Power Mode [Auto]
USB3.2_5 Type C Power Mode [Auto]
ASMedia Storage Controller [Disabled]
Restore AC Power Loss [Power Off]
Energy Star Ready [Disabled]
ErP Ready [Disabled]
Power On By PCI-E [Disabled]
Power On By RTC [Disabled]
Device [N\A]
CPU Temperature [Monitor]
CPU Package Temperature [Monitor]
MotherBoard Temperature [Monitor]
VRM Temperature [Monitor]
Chipset Temperature [Monitor]
T_Sensor Temperature [Monitor]
DIMM.2 Sensor 1 Temperature [Monitor]
DIMM.2 Sensor 2 Temperature [Monitor]
Water In T Sensor Temperature [Monitor]
Water Out T Sensor Temperature [Monitor]
EXT_Sensor1 Temperature [Monitor]
EXT_Sensor2 Temperature [Monitor]
EXT_Sensor3 Temperature [Monitor]
CPU Fan Speed [Monitor]
CPU Optional Fan Speed [Monitor]
Chassis Fan 1 Speed [Monitor]
Chassis Fan 2 Speed [Monitor]
Chassis Fan 3 Speed [Monitor]
W_PUMP+ Speed [Monitor]
AIO PUMP Speed [Monitor]
Extension Fan 1 Speed [Monitor]
Extension Fan 2 Speed [Monitor]
Extension Fan 3 Speed [Monitor]
Extension Fan 4 Speed [Monitor]
Extension Fan 5 Speed [Monitor]
Extension Fan 6 Speed [Monitor]
CPU Core Voltage [Monitor]
12V Voltage [Monitor]
5V Voltage [Monitor]
3.3V Voltage [Monitor]
Flow Rate [Monitor]
AI Cooling [Disabled]
CPU Q-Fan Control [Auto]
CPU Fan Step Up [0 sec]
CPU Fan Step Down [0 sec]
CPU Fan Speed Lower Limit [200 RPM]
CPU Fan Profile [Standard]
Chassis Fan 1 Q-Fan Control [Auto]
Chassis Fan 1 Q-Fan Source [CPU]
Chassis Fan 1 Step Up [0 sec]
Chassis Fan 1 Step Down [0 sec]
Chassis Fan 1 Speed Low Limit [200 RPM]
Chassis Fan 1 Profile [Standard]
Chassis Fan 2 Q-Fan Control [Auto]
Chassis Fan 2 Q-Fan Source [CPU]
Chassis Fan 2 Step Up [0 sec]
Chassis Fan 2 Step Down [0 sec]
Chassis Fan 2 Speed Low Limit [200 RPM]
Chassis Fan 2 Profile [Standard]
Chassis Fan 3 Q-Fan Control [Auto]
Chassis Fan 3 Q-Fan Source [CPU]
Chassis Fan 3 Step Up [0 sec]
Chassis Fan 3 Step Down [0 sec]
Chassis Fan 3 Speed Low Limit [200 RPM]
Chassis Fan 3 Profile [Standard]
Extension Fan 1 Q-Fan Control [Auto]
Extension Fan 1 Q-Fan Source [CPU]
Extension Fan 1 Step Up [0 sec]
Extension Fan 1 Step Down [0 sec]
Extension Fan 1 Speed Low Limit [200 RPM]
Extension Fan 1 Profile [Standard]
Extension Fan 2 Q-Fan Control [Auto]
Extension Fan 2 Q-Fan Source [CPU]
Extension Fan 2 Step Up [0 sec]
Extension Fan 2 Step Down [0 sec]
Extension Fan 2 Speed Low Limit [200 RPM]
Extension Fan 2 Profile [Standard]
Extension Fan 3 Q-Fan Control [Auto]
Extension Fan 3 Q-Fan Source [CPU]
Extension Fan 3 Step Up [0 sec]
Extension Fan 3 Step Down [0 sec]
Extension Fan 3 Speed Low Limit [200 RPM]
Extension Fan 3 Profile [Standard]
Extension Fan 4 Q-Fan Control [Auto]
Extension Fan 4 Q-Fan Source [CPU]
Extension Fan 4 Step Up [0 sec]
Extension Fan 4 Step Down [0 sec]
Extension Fan 4 Speed Low Limit [200 RPM]
Extension Fan 4 Profile [Standard]
Extension Fan 5 Q-Fan Control [Auto]
Extension Fan 5 Q-Fan Source [CPU]
Extension Fan 5 Step Up [0 sec]
Extension Fan 5 Step Down [0 sec]
Extension Fan 5 Speed Low Limit [200 RPM]
Extension Fan 5 Profile [Standard]
Extension Fan 6 Q-Fan Control [Auto]
Extension Fan 6 Q-Fan Source [CPU]
Extension Fan 6 Step Up [0 sec]
Extension Fan 6 Step Down [0 sec]
Extension Fan 6 Speed Low Limit [200 RPM]
Extension Fan 6 Profile [Standard]
WATER PUMP+ Control [Disabled]
AIO PUMP Control [Disabled]
CPU Temperature LED Switch [Enabled]
Launch CSM [Disabled]
OS Type [Other OS]
Fast Boot [Enabled]
Next Boot after AC Power Loss [Fast Boot]
Boot Logo Display [Auto]
POST Delay Time [0 sec]
Bootup NumLock State [On]
Wait For 'F1' If Error [Enabled]
AMI Native NVMe Driver Support [Enabled]
Option ROM Messages [Force BIOS]
Interrupt 19 Capture [Disabled]
Setup Mode [Advanced Mode]
Boot Sector (MBR/GPT) Recovery Policy [Local User Control]
Next Boot Recovery Action [Skip]
Flexkey [Reset]
Setup Animator [Disabled]
Load from Profile [4]
Profile Name [46/17test]
Save to Profile [4]
DIMM Slot Number [DIMM_A1]
Download & Install ARMOURY CRATE app [Disabled]

Quote:

---

Originally Posted by nosam1g

No the disk check came after i did a Microsoft update lol . i have it turned off now.
If it was boot instability it would let me know in POST and it would not go any further. I really think its the GFX card , because the spindle loading i think it is trying to find the gfx driver before logging in. As you saw in the video it does then pick it up after i login.

Ill try ur suggestions once i get back from work. Ill try to take pictures of a lot of the tabs.. What are the main things to check .. I have built a few pcs and i have never had to change bios settings after i installed a pc. my bios is 607

When in the bios with a USB formatted to FAT 32 go to Tool, Load/Save Profile, CTR+F2
Can you explain how to do this .

---

Also in your video description you say that is with no overclock but when booting it says right on the screen 43% overclock is set. So something is not right. Did you hit F5 in the bios to load optimized defaults?

Edit I see you said you also did it without an overclock.

I see I left out a step for saving the bios settings. When in the bios with a USB formatted to FAT 32 go to Tool, User Profile, Load/Save Profile and then CTR+F2.

I would post screen shots but for some reason it says my files are too large and if I edit them down they are tiny and hard to read. I obviously do not post online much ;)

How do you go about posting your screen shots?

Quote:

---

Originally Posted by bscool

I see I left out a step for saving the bios settings. When in the bios with a USB formatted to FAT 32 go to Tool, User Profile, Load/Save Profile and then CTR+F2.

I would post screen shots but for some reason it says my files are too large and if I edit them down they are tiny and hard to read. I obviously do not post online much ;)

How do you go about posting your screen shots?

---

yes so originally this issue was present when i had no overclocking. I can run the pc full functionally , it runs fine , and in games its a monster. So i wanted to do Optimized Overclocking and i enabled XMP in bios. Its the whole purpose of why i chose this motherboard for the overclocking capabilities . Yes it configured my ram to 4500mhz and 1.45V. When geting to post it booted with no issues and ive been using it for a week with no problems.

New issue arised where i was trying to save the bios profile and my flash drive doesnt work. When logged in and in device manager in USB bus controller i have unknown usb device descriptor failed . Tried running troubleshooting hardware and device , didnt work, tried uninstalling/reinstalling didnt work. LOL

Where do i find the MRC fast boot and MCH ?

Quote:

---

Originally Posted by nosam1g

yes so originally this issue was present when i had no overclocking. I can run the pc full functionally , it runs fine , and in games its a monster. So i wanted to do Optimized Overclocking and i enabled XMP in bios. Its the whole purpose of why i chose this motherboard for the overclocking capabilities . Yes it configured my ram to 4500mhz and 1.45V. When geting to post it booted with no issues and ive been using it for a week with no problems.

New issue arised where i was trying to save the bios profile and my flash drive doesnt work. When logged in and in device manager in USB bus controller i have unknown usb device descriptor failed . Tried running troubleshooting hardware and device , didnt work, tried uninstalling/reinstalling didnt work. LOL

Where do i find the MRC fast boot and MCH ?

---

Extreme Tweaker Tab, down to Dram Timing Tab, then scroll down to find them. Bios also has search at the top or F9 to find items.

The board has dual bios, have you tried the other bios?

It seems like bios 062 is the best one so far(as in RAM OC stability). But none have given me any kind of boot issue like you have. Maybe try another clean install of Windows 2004? Or reinstall GPU drivers?

The reason I thought it was with the RAM training is I have had issues like that when OCing the ram and it not being stable. But you said you can game and it is fine so the RAM stability might not be your issue.

You could also try SFC /Scannow to check for any Windows errors. https://support.microsoft.com/en-us/...ystem%20files.

You don't have something silly like the slow boot switch on used for LN2 overclocking do you ?

Quote:

---

Originally Posted by bscool

Extreme Tweaker Tab, down to Dram Timing Tab, then scroll down to find them. Bios also has search at the top or F9 to find items.

The board has dual bios, have you tried the other bios?

It seems like bios 062 is the best one so far(as in RAM OC stability). But none have given me any kind of boot issue like you have. Maybe try another clean install of Windows 2004? Or reinstall GPU drivers?

The reason I thought it was with the RAM training is I have had issues like that when OCing the ram and it not being stable. But you said you can game and it is fine so the RAM stability might not be your issue.

---

Lol windows 2004 are you serious >?

What kind of ram do you have . I have 16gb 8x2 4500mhz TeamGroup
sometimes it depends on the ram ..
Ive reinstalled windows and gpu drivers already ..

Quote:

---

Originally Posted by nosam1g

Lol windows 2004 are you serious >?

What kind of ram do you have . I have 16gb 8x2 4500mhz TeamGroup
sometimes it depends on the ram ..
Ive reinstalled windows and gpu drivers already ..

---

What version of windows are you running? 2004 is the latest https://docs.microsoft.com/en-us/win...0-version-2004

I have TEAM 4500, Gskill 4600 18 sticks and currently running Gskill 4800 kits. I havent tried anything other than the 4800 kit.

I also have an Apex XI and I know that board is not stable with XMP on high mem sticks and even the APEX XII is not stable with the Gskill 4800 just setting XMP. I have to manually set voltages and timings. People think these boards are plug play with high XMP memory but in my experience they are not.

I have messed quite a few different boards from MSI, Gigabyte Asrock and memory kits from 3200/14 to the 4800 kits and I know they do not like 4133+ with just XMP. It might work for some but for the majority they need manual tweaking.

I put the Team 4500 kit in the APEX Xll and it is working for me with and without XMP. XMP booted right up with no manual tweaking but like I said before voltages are really high on VCCSA @1.68. The 1.45v you mentioned is DRAM voltage.

I haven't tested stability but I just wanted to see if it boots or I had issues with the Nvidia control panel. No issue using the latest Nvidia drivers 446.13 on Windows 10 2004 for me. My GPU is MSI 2080 TI Gaming X. I also used defaults for bios settings with bios 403 to try and replicate the most likely to have issues. I also have no CPU and that will effect ram stability.

Ill report if I have any issues with the Team 4500. I have bios 069 on my other bios ill try and see how it works as so far that seems the best bios from my testing.

Edit Newer bios 069 sets a lower SA voltage of 1.52 vs 1.68 on the older bios when left on Auto. So far no issues with the Team 4500 XMP and using AI OC.

I used Gskill 4600 royal gold kit with xmp and AI overclocking just for fun and it run great and keeps retraining the CPU faster and faster.. The ram is running a solid 2300mhz.

I haven't tried manual OC yet. I have to replace my board it's bad per ASUS but it runs currently.. Just won't shut down.

Ok bro from everything you have written I think it is time for a fresh install of windows 100%. Try that before you try anything else lol.

Fresh install of windows, install your chipset drivers from the site, get the newest nvidia driver, turn off fast boot in bios, and do some restarts lol. Sounds like a windows issue vs a bios issue to me firsthand.

Quote:

---

Originally Posted by 1mluer

I used Gskill 4600 royal gold kit with xmp and AI overclocking just for fun and it run great and keeps retraining the CPU faster and faster.. The ram is running a solid 2300mhz.

I haven't tried manual OC yet. I have to replace my board it's bad per ASUS but it runs currently.. Just won't shut down.

---

So you got around to contacting ASUS ? Is that what they refereed to do, any troubleshootin ? I havent had the time to get around to ask ASUS about my issue yet

Quote:

---

Originally Posted by m4ttjirm

Ok bro from everything you have written I think it is time for a fresh install of windows 100%. Try that before you try anything else lol.

Fresh install of windows, install your chipset drivers from the site, get the newest nvidia driver, turn off fast boot in bios, and do some restarts lol. Sounds like a windows issue vs a bios issue to me firsthand.

---

Yes i could try a fresh install of windows. Im going to post my Profile results in a bit

EDIT:** I get this message when trying to save it to my flash drive
USB Flash drive with NTFS not supported

Quote:

---

Originally Posted by bscool

I put the Team 4500 kit in the APEX Xll and it is working for me with and without XMP. XMP booted right up with no manual tweaking but like I said before voltages are really high on VCCSA @1.68. The 1.45v you mentioned is DRAM voltage.

I haven't tested stability but I just wanted to see if it boots or I had issues with the Nvidia control panel. No issue using the latest Nvidia drivers 446.13 on Windows 10 2004 for me. My GPU is MSI 2080 TI Gaming X. I also used defaults for bios settings with bios 403 to try and replicate the most likely to have issues. I also have no CPU and that will effect ram stability.

Ill report if I have any issues with the Team 4500. I have bios 069 on my other bios ill try and see how it works as so far that seems the best bios from my testing.

Edit Newer bios 069 sets a lower SA voltage of 1.52 vs 1.68 on the older bios when left on Auto. So far no issues with the Team 4500 XMP and using AI OC.

---

Good to hear your overclocking is working out. Where can i view SA voltage ? Not sure what bioses those are i just went to the ASUS site and support to dl latest which was Version 0607


EDIT ** Just did the MRC and MCH settings that were suggested earlier .. and im not sure if it booted faster but the nivida drivers were not recognized right away how they should be.
Im starting to think this is a Motherboard or Chip issue. I still should reinstall windows

Quote:

---

Originally Posted by nosam1g

So you got around to contacting ASUS ? Is that what they refereed to do, any troubleshootin ? I havent had the time to get around to ask ASUS about my issue yet



Yes i could try a fresh install of windows. Im going to post my Profile results in a bit

EDIT:** I get this message when trying to save it to my flash drive
USB Flash drive with NTFS not supported




Good to hear your overclocking is working out. Where can i view SA voltage ? Not sure what bioses those are i just went to the ASUS site and support to dl latest which was Version 0607


EDIT ** Just did the MRC and MCH settings that were suggested earlier .. and im not sure if it booted faster but the nivida drivers were not recognized right away how they should be.
Im starting to think this is a Motherboard or Chip issue. I still should reinstall windows

---

yes I have a bad board. I was requested to return and get a new one or send it to the Western European RMA facility. People in the US are screwed again for a while before they release the board here. I was told so much during the support call. APEX and Extreme not slated for North America yet. all these preorder sites are BS right now

Only things i have done with this PC is Overclocking Optimized through Asus Suite
Enabled XMP 1 for 4500mhz Ram
and thats about it.
Im thinking Asus just needs to update drivers to allow my GFX card to properly register upon bootin up. My only issue is my gfx card not being registered , which is what i think my OS is trying to figure out when booting (hence the spindle) Otherwise pc runs great .
I got around to figuring out how to get my bios settings here they are


[2020/06/20 15:43:10]
Ai Overclock Tuner [XMP I]
XMP [XMP DDR4-4504 18-20-20-44-1.45V]
BCLK Frequency [100.0000]
PCIE Frequency [100.0000]
ASUS MultiCore Enhancement [Auto – Lets BIOS Optimize]
SVID Behavior [Auto]
AVX Instruction Core Ratio Negative Offset [Auto]
CPU Core Ratio [AI Optimized]
Optimized AVX Frequency [Normal Use]
BCLK Frequency : DRAM Frequency Ratio [Auto]
DRAM Odd Ratio Mode [Enabled]
DRAM Frequency [DDR4-4500MHz]
Xtreme Tweaking [Disabled]
CPU SVID Support [Auto]
Maximus Tweak [Auto]
DRAM CAS# Latency [18]
DRAM RAS# to CAS# Delay [20]
DRAM RAS# ACT Time [44]
DRAM Command Rate [Auto]
DRAM RAS# to RAS# Delay L [Auto]
DRAM RAS# to RAS# Delay S [Auto]
DRAM REF Cycle Time [Auto]
DRAM REF Cycle Time 2 [Auto]
DRAM REF Cycle Time 4 [Auto]
DRAM Refresh Interval [Auto]
DRAM WRITE Recovery Time [Auto]
DRAM READ to PRE Time [Auto]
DRAM FOUR ACT WIN Time [Auto]
DRAM WRITE to READ Delay [Auto]
DRAM WRITE to READ Delay L [Auto]
DRAM WRITE to READ Delay S [Auto]
DRAM CKE Minimum Pulse Width [Auto]
DRAM Write Latency [Auto]
ODT RTT WR (CHA) [Auto]
ODT RTT PARK (CHA) [Auto]
ODT RTT NOM (CHA) [Auto]
ODT RTT WR (CHB) [Auto]
ODT RTT PARK (CHB) [Auto]
ODT RTT NOM (CHB) [Auto]
ODT_READ_DURATION [Auto]
ODT_READ_DELAY [Auto]
ODT_WRITE_DURATION [Auto]
ODT_WRITE_DELAY [Auto]
Data Rising Slope [Auto]
Data Rising Slope Offset [Auto]
Cmd Rising Slope [Auto]
Cmd Rising Slope Offset [Auto]
Ctl Rising Slope [Auto]
Ctl Rising Slope Offset [Auto]
Clk Rising Slope [Auto]
Clk Rising Slope Offset [Auto]
Data Falling Slope [Auto]
Data Falling Slope Offset [Auto]
Cmd Falling Slope [Auto]
Cmd Falling Slope Offset [Auto]
Ctl Falling Slope [Auto]
Ctl Falling Slope Offset [Auto]
Clk Falling Slope [Auto]
Clk Falling Slope Offset [Auto]
DRAM RTL INIT value [Auto]
DRAM RTL (CHA DIMM0 Rank0) [Auto]
DRAM RTL (CHA DIMM0 Rank1) [Auto]
DRAM RTL (CHA DIMM1 Rank0) [Auto]
DRAM RTL (CHA DIMM1 Rank1) [Auto]
DRAM RTL (CHB DIMM0 Rank0) [Auto]
DRAM RTL (CHB DIMM0 Rank1) [Auto]
DRAM RTL (CHB DIMM1 Rank0) [Auto]
DRAM RTL (CHB DIMM1 Rank1) [Auto]
DRAM IOL (CHA DIMM0 Rank0) [Auto]
DRAM IOL (CHA DIMM0 Rank1) [Auto]
DRAM IOL (CHA DIMM1 Rank0) [Auto]
DRAM IOL (CHA DIMM1 Rank1) [Auto]
DRAM IOL (CHB DIMM0 Rank0) [Auto]
DRAM IOL (CHB DIMM0 Rank1) [Auto]
DRAM IOL (CHB DIMM1 Rank0) [Auto]
DRAM IOL (CHB DIMM1 Rank1) [Auto]
CHA IO_Latency_offset [Auto]
CHB IO_Latency_offset [Auto]
CHA RFR delay [Auto]
CHB RFR delay [Auto]
Early Command Training [Auto]
SenseAmp Offset Training [Enabled]
Early ReadMPR Timing Centering 2D [Enabled]
Read MPR Training [Enabled]
Receive Enable Training [Enabled]
Jedec Write Leveling [Enabled]
LPDDR4 Write DQ DQS Retraining [Enabled]
Early Write Time Centering 2D [Auto]
Early Read Time Centering 2D [Auto]
Write Timing Centering 1D [Enabled]
Write Voltage Centering 1D [Auto]
Read Timing Centering 1D [Auto]
Dimm ODT Training* [Auto]
DIMM RON Training* [Auto]
Write Drive Strength/Equalization 2D* [Auto]
Write Slew Rate Training* [Auto]
Read ODT Training* [Auto]
Read Equalization Training* [Auto]
Read Amplifier Training* [Auto]
Write Timing Centering 2D [Auto]
Read Timing Centering 2D [Auto]
Command Voltage Centering [Auto]
Write Voltage Centering 2D [Auto]
Read Voltage Centering 2D [Auto]
Late Command Training [Auto]
Round Trip Latency [Auto]
Turn Around Timing Training [Disabled]
Rank Margin Tool [Auto]
Margin Check Limit [Disabled]
Memory Test [Disabled]
DIMM SPD Alias Test [Auto]
Receive Enable Centering 1D [Auto]
Retrain Margin Check [Disabled]
CMD Drive Strength and Tx Equalization [Auto]
CMD Slew Rate Training [Auto]
Write Drive Strength Up/Dn independently [Disabled]
tRDRD_sg_Training [Auto]
tRDRD_sg_Runtime [Auto]
tRDRD_dg [Auto]
tRDWR_sg [Auto]
tRDWR_dg [Auto]
tWRWR_sg [Auto]
tWRWR_dg [Auto]
tWRRD_sg [Auto]
tWRRD_dg [Auto]
tRDRD_dr [Auto]
tRDRD_dd [Auto]
tRDWR_dr [Auto]
tRDWR_dd [Auto]
tWRWR_dr [Auto]
tWRWR_dd [Auto]
tWRRD_dr [Auto]
tWRRD_dd [Auto]
TWRPRE [Auto]
TRDPRE [Auto]
tREFIX9 [Auto]
OREF_RI [Auto]
MRC Fast Boot [Disabled]
Delay after Train [Disabled]
DRAM CLK Period [Auto]
Memory Scrambler [Enabled]
Channel A DIMM Control [Enable both DIMMs]
Channel B DIMM Control [Enable both DIMMs]
Trace Centering [Disabled]
MCH Full Check [Enabled]
Mem Over Clock Fail Count [Auto]
Training Profile [Auto]
DLLBwEn [Auto]
Legacy Mode [Disabled]
SPD Write Disable [TRUE]
XTU Setting [Auto]
Voltage Monitor [Die Sense]
CPU Load-line Calibration [Auto]
Synch ACDC Loadline with VRM Loadline [Disabled]
CPU Current Capability [Auto]
CPU VRM Switching Frequency [Auto]
VRM Spread Spectrum [Auto]
CPU Power Duty Control [T.Probe]
CPU Power Phase Control [Auto]
CPU Power Thermal Control [130]
CPU VRM Thermal Control [Auto]
DRAM Current Capability [100%]
DRAM Switching Frequency [Auto]
CPU Core/Cache Boot Voltage [Auto]
DMI Boot Voltage [Auto]
CPU System Agent Boot Voltage [Auto]
CPU VCCIO Boot Voltage [Auto]
PLL Termination Boot voltage [Auto]
CPU Standby Boot Voltage [Auto]
Maximum CPU Core Temperature [Auto]
CPU Core/Cache Current Limit Max. [Auto]
Long Duration Package Power Limit [Auto]
Package Power Time Window [Auto]
Short Duration Package Power Limit [Auto]
IA AC Load Line [Auto]
IA DC Load Line [Auto]
TVB Voltage Optimizations [Auto]
TVB Ratio Clipping [Auto]
V-Max Stress [Auto]
Offset Mode Sign 1 [+]
V/F Point 1 Offset [Auto]
Offset Mode Sign 2 [+]
V/F Point 2 Offset [Auto]
Offset Mode Sign 3 [+]
V/F Point 3 Offset [Auto]
Offset Mode Sign 4 [+]
V/F Point 4 Offset [Auto]
Offset Mode Sign 5 [+]
V/F Point 5 Offset [Auto]
Offset Mode Sign 6 [+]
V/F Point 6 Offset [Auto]
Offset Mode Sign 7 [+]
V/F Point 7 Offset [Auto]
Offset Mode Sign 8 [+]
V/F Point 8 Offset [Auto]
Realtime Memory Timing [Enabled]
FCLK Frequency for Early Power On [Auto]
Initial BCLK Frequency [Auto]
BCLK Amplitude [Auto]
BCLK Slew Rate [Auto]
BCLK Spread Spectrum [Auto]
BCLK Frequency Slew Rate [Auto]
PCIE/DMI Amplitude [Auto]
PCIE/DMI Spread Spectrum [Auto]
PCIE/DMI Frequency Slew Rate [Auto]
PCIE/DMI Slew Rate [Auto]
Cold Boot PCIE Frequency [Auto]
DRAM VTT Voltage [Auto]
VPPDDR Voltage [Auto]
DMI Voltage [Auto]
Internal PLL Voltage [Auto]
GT PLL Voltage [Auto]
Ring PLL Voltage [Auto]
System Agent PLL Voltage [Auto]
Memory Controller PLL Voltage [Auto]
CPU Standby Voltage [Auto]
PLL Bandwidth [Auto]
Eventual DRAM Voltage [Auto]
Eventual CPU Standby Voltage [Auto]
Eventual PLL Termination Voltage [Auto]
Eventual CPU VCCIO Voltage [Auto]
Eventual DMI Voltage [Auto]
System Agent Bandgap Workaround [Auto]
Package Temperature Threshold [Auto]
Regulate Frequency by above Threshold [Auto]
Cooler Efficiency Customize [Keep Training]
Cooler Re-evaluation Algorithm [Normal]
Optimism Scale [100]
Ring Down Bin [Auto]
Min. CPU Cache Ratio [Auto]
Max CPU Cache Ratio [Auto]
BCLK Aware Adaptive Voltage [Enabled]
CPU Core/Cache Voltage [Auto]
DRAM Voltage [1.45000]
CPU VCCIO Voltage [Auto]
CPU System Agent Voltage [Auto]
PLL Termination Voltage [Auto]
PCH Core Voltage [Auto]
DRAM CTRL REF Voltage on CHA [Auto]
DRAM CTRL REF Voltage on CHB [Auto]
DRAM DATA REF Voltage on CHA DIMM0 Rank0 BL0 [Auto]
DRAM DATA REF Voltage on CHA DIMM0 Rank0 BL1 [Auto]
DRAM DATA REF Voltage on CHA DIMM0 Rank0 BL2 [Auto]
DRAM DATA REF Voltage on CHA DIMM0 Rank0 BL3 [Auto]
DRAM DATA REF Voltage on CHA DIMM0 Rank0 BL4 [Auto]
DRAM DATA REF Voltage on CHA DIMM0 Rank0 BL5 [Auto]
DRAM DATA REF Voltage on CHA DIMM0 Rank0 BL6 [Auto]
DRAM DATA REF Voltage on CHA DIMM0 Rank0 BL7 [Auto]
DRAM DATA REF Voltage on CHA DIMM0 Rank1 BL0 [Auto]
DRAM DATA REF Voltage on CHA DIMM0 Rank1 BL1 [Auto]
DRAM DATA REF Voltage on CHA DIMM0 Rank1 BL2 [Auto]
DRAM DATA REF Voltage on CHA DIMM0 Rank1 BL3 [Auto]
DRAM DATA REF Voltage on CHA DIMM0 Rank1 BL4 [Auto]
DRAM DATA REF Voltage on CHA DIMM0 Rank1 BL5 [Auto]
DRAM DATA REF Voltage on CHA DIMM0 Rank1 BL6 [Auto]
DRAM DATA REF Voltage on CHA DIMM0 Rank1 BL7 [Auto]
DRAM DATA REF Voltage on CHA DIMM1 Rank0 BL0 [Auto]
DRAM DATA REF Voltage on CHA DIMM1 Rank0 BL1 [Auto]
DRAM DATA REF Voltage on CHA DIMM1 Rank0 BL2 [Auto]
DRAM DATA REF Voltage on CHA DIMM1 Rank0 BL3 [Auto]
DRAM DATA REF Voltage on CHA DIMM1 Rank0 BL4 [Auto]
DRAM DATA REF Voltage on CHA DIMM1 Rank0 BL5 [Auto]
DRAM DATA REF Voltage on CHA DIMM1 Rank0 BL6 [Auto]
DRAM DATA REF Voltage on CHA DIMM1 Rank0 BL7 [Auto]
DRAM DATA REF Voltage on CHA DIMM1 Rank1 BL0 [Auto]
DRAM DATA REF Voltage on CHA DIMM1 Rank1 BL1 [Auto]
DRAM DATA REF Voltage on CHA DIMM1 Rank1 BL2 [Auto]
DRAM DATA REF Voltage on CHA DIMM1 Rank1 BL3 [Auto]
DRAM DATA REF Voltage on CHA DIMM1 Rank1 BL4 [Auto]
DRAM DATA REF Voltage on CHA DIMM1 Rank1 BL5 [Auto]
DRAM DATA REF Voltage on CHA DIMM1 Rank1 BL6 [Auto]
DRAM DATA REF Voltage on CHA DIMM1 Rank1 BL7 [Auto]
DRAM DATA REF Voltage on CHB DIMM0 Rank0 BL0 [Auto]
DRAM DATA REF Voltage on CHB DIMM0 Rank0 BL1 [Auto]
DRAM DATA REF Voltage on CHB DIMM0 Rank0 BL2 [Auto]
DRAM DATA REF Voltage on CHB DIMM0 Rank0 BL3 [Auto]
DRAM DATA REF Voltage on CHB DIMM0 Rank0 BL4 [Auto]
DRAM DATA REF Voltage on CHB DIMM0 Rank0 BL5 [Auto]
DRAM DATA REF Voltage on CHB DIMM0 Rank0 BL6 [Auto]
DRAM DATA REF Voltage on CHB DIMM0 Rank0 BL7 [Auto]
DRAM DATA REF Voltage on CHB DIMM0 Rank1 BL0 [Auto]
DRAM DATA REF Voltage on CHB DIMM0 Rank1 BL1 [Auto]
DRAM DATA REF Voltage on CHB DIMM0 Rank1 BL2 [Auto]
DRAM DATA REF Voltage on CHB DIMM0 Rank1 BL3 [Auto]
DRAM DATA REF Voltage on CHB DIMM0 Rank1 BL4 [Auto]
DRAM DATA REF Voltage on CHB DIMM0 Rank1 BL5 [Auto]
DRAM DATA REF Voltage on CHB DIMM0 Rank1 BL6 [Auto]
DRAM DATA REF Voltage on CHB DIMM0 Rank1 BL7 [Auto]
DRAM DATA REF Voltage on CHB DIMM1 Rank0 BL0 [Auto]
DRAM DATA REF Voltage on CHB DIMM1 Rank0 BL1 [Auto]
DRAM DATA REF Voltage on CHB DIMM1 Rank0 BL2 [Auto]
DRAM DATA REF Voltage on CHB DIMM1 Rank0 BL3 [Auto]
DRAM DATA REF Voltage on CHB DIMM1 Rank0 BL4 [Auto]
DRAM DATA REF Voltage on CHB DIMM1 Rank0 BL5 [Auto]
DRAM DATA REF Voltage on CHB DIMM1 Rank0 BL6 [Auto]
DRAM DATA REF Voltage on CHB DIMM1 Rank0 BL7 [Auto]
DRAM DATA REF Voltage on CHB DIMM1 Rank1 BL0 [Auto]
DRAM DATA REF Voltage on CHB DIMM1 Rank1 BL1 [Auto]
DRAM DATA REF Voltage on CHB DIMM1 Rank1 BL2 [Auto]
DRAM DATA REF Voltage on CHB DIMM1 Rank1 BL3 [Auto]
DRAM DATA REF Voltage on CHB DIMM1 Rank1 BL4 [Auto]
DRAM DATA REF Voltage on CHB DIMM1 Rank1 BL5 [Auto]
DRAM DATA REF Voltage on CHB DIMM1 Rank1 BL6 [Auto]
DRAM DATA REF Voltage on CHB DIMM1 Rank1 BL7 [Auto]
PCI Express Native Power Management [Disabled]
DMI Link ASPM Control [Disabled]
ASPM [Disabled]
L1 Substates [Disabled]
PCI Express Clock Gating [Enabled]
DMI Link ASPM Control [Disabled]
PEG - ASPM [Disabled]
Software Guard Extensions (SGX) [Disabled]
Tcc Offset Time Window [Auto]
Hardware Prefetcher [Enabled]
Adjacent Cache Line Prefetch [Enabled]
Intel (VMX) Virtualization Technology [Disabled]
Active Processor Cores [All]
Hyper-Threading [Enabled]
Hyper-Threading of Core 0 [Enabled]
Hyper-Threading of Core 1 [Enabled]
Hyper-Threading of Core 2 [Enabled]
Hyper-Threading of Core 3 [Enabled]
Hyper-Threading of Core 4 [Enabled]
Hyper-Threading of Core 5 [Enabled]
Hyper-Threading of Core 6 [Enabled]
Hyper-Threading of Core 7 [Enabled]
Hyper-Threading of Core 8 [Enabled]
Hyper-Threading of Core 9 [Enabled]
MonitorMWait [Enabled]
Boot performance mode [Auto]
Intel(R) SpeedStep(tm) [Auto]
Intel(R) Speed Shift Technology [Auto]
Intel(R) Turbo Boost Max Technology 3.0 [Enabled]
Runtime SMM Polling [8 Sec]
Turbo Mode [Enabled]
Thermal Monitor [Enabled]
Dual Tau Boost [Disabled]
VT-d [Disabled]
Above 4G Decoding [Enabled]
Memory Remap [Enabled]
PCIEX16_1 Link Speed [Auto]
PCIEX16_2 Link Speed [Auto]
PCIe Speed [Gen3]
SATA Controller(s) [Enabled]
SATA Mode Selection [AHCI]
Aggressive LPM Support [Disabled]
SMART Self Test [Enabled]
SATA6G_1(Black) [Enabled]
SATA6G_1 Hot Plug [Disabled]
SATA6G_2(Black) [Enabled]
SATA6G_2 Hot Plug [Disabled]
SATA6G_3(Black) [Enabled]
SATA6G_3 Hot Plug [Disabled]
SATA6G_4(Black) [Enabled]
SATA6G_4 Hot Plug [Disabled]
SATA6G_5(Black) [Enabled]
SATA6G_5 Hot Plug [Disabled]
SATA6G_6(Black) [Enabled]
SATA6G_6 Hot Plug [Disabled]
PTT [Disable]
Discrete Thunderbolt(TM) Support [Disabled]
SR-IOV Support [Disabled]
Legacy USB Support [Enabled]
XHCI Hand-off [Enabled]
U32G2_1 [Enabled]
U32G2_2 [Enabled]
U32G2_3 [Enabled]
U32G2_4 [Enabled]
U32G1_7 [Enabled]
U32G1_8 [Enabled]
U32G1_E1 [Enabled]
U32G1_E2 [Enabled]
U32G1_E3 [Enabled]
U32G1_E4 [Enabled]
U32G1_9 [Enabled]
SP_USB11 [Enabled]
U32G2_5 [Enabled]
U32G2_C6 [Enabled]
Network Stack [Disabled]
Hyper M.2X16 [Enabled]
HD Audio [Enabled]
Intel LAN [Enabled]
Intel LAN PXE Option ROM [Disabled]
USB power delivery in Soft Off state (S5) [Enabled]
Connectivity mode (Wi-Fi & Bluetooth) [Enabled]
When system is in working state [Aura Only]
When system is in sleep, hibernate or soft off states [Stealth Mode]
M.2_1 Configuration [Auto]
DIMM2_1 Configuration [Auto]
DIMM2_2 Configuration [Auto]
U32G2_C6 Type C Power Mode [Auto]
USB3.2_5 Type C Power Mode [Auto]
ASMedia Storage Controller [Enabled]
Windows Hot-plug Notification [Disabled]
ASPM Support [Disabled]
Restore AC Power Loss [Power Off]
Energy Star Ready [Disabled]
ErP Ready [Disabled]
Power On By PS/2 Keyboard [Space Bar]
Power On By PCI-E [Disabled]
Power On By RTC [Disabled]
Device [Samsung SSD 860 EVO 1TB]
CPU Temperature [Monitor]
CPU Package Temperature [Monitor]
MotherBoard Temperature [Monitor]
VRM Temperature [Monitor]
Chipset Temperature [Monitor]
T_Sensor Temperature [Monitor]
DIMM.2 Sensor 1 Temperature [Monitor]
DIMM.2 Sensor 2 Temperature [Monitor]
Water In T Sensor Temperature [Monitor]
Water Out T Sensor Temperature [Monitor]
EXT_Sensor1 Temperature [Monitor]
EXT_Sensor2 Temperature [Monitor]
EXT_Sensor3 Temperature [Monitor]
CPU Fan Speed [Monitor]
CPU Optional Fan Speed [Monitor]
Chassis Fan 1 Speed [Monitor]
Chassis Fan 2 Speed [Monitor]
Chassis Fan 3 Speed [Monitor]
W_PUMP+ Speed [Monitor]
AIO PUMP Speed [Monitor]
Extension Fan 1 Speed [Monitor]
Extension Fan 2 Speed [Monitor]
Extension Fan 3 Speed [Monitor]
Extension Fan 4 Speed [Monitor]
Extension Fan 5 Speed [Monitor]
Extension Fan 6 Speed [Monitor]
CPU Core Voltage [Monitor]
12V Voltage [Monitor]
5V Voltage [Monitor]
3.3V Voltage [Monitor]
Flow Rate [Monitor]
AI Cooling [Enabled]
CPU Q-Fan Control [Auto]
CPU Fan Step Up [0 sec]
CPU Fan Step Down [0 sec]
CPU Fan Speed Lower Limit [200 RPM]
CPU Fan Profile [Standard]
Chassis Fan 1 Q-Fan Control [Auto]
Chassis Fan 1 Q-Fan Source [CPU]
Chassis Fan 1 Step Up [0 sec]
Chassis Fan 1 Step Down [0 sec]
Chassis Fan 1 Speed Low Limit [200 RPM]
Chassis Fan 1 Profile [Standard]
Chassis Fan 2 Q-Fan Control [Auto]
Chassis Fan 2 Q-Fan Source [CPU]
Chassis Fan 2 Step Up [0 sec]
Chassis Fan 2 Step Down [0 sec]
Chassis Fan 2 Speed Low Limit [200 RPM]
Chassis Fan 2 Profile [Standard]
Chassis Fan 3 Q-Fan Control [Auto]
Chassis Fan 3 Q-Fan Source [CPU]
Chassis Fan 3 Step Up [0 sec]
Chassis Fan 3 Step Down [0 sec]
Chassis Fan 3 Speed Low Limit [200 RPM]
Chassis Fan 3 Profile [Standard]
Extension Fan 1 Q-Fan Control [Auto]
Extension Fan 1 Q-Fan Source [CPU]
Extension Fan 1 Step Up [0 sec]
Extension Fan 1 Step Down [0 sec]
Extension Fan 1 Speed Low Limit [200 RPM]
Extension Fan 1 Profile [Standard]
Extension Fan 2 Q-Fan Control [Auto]
Extension Fan 2 Q-Fan Source [CPU]
Extension Fan 2 Step Up [0 sec]
Extension Fan 2 Step Down [0 sec]
Extension Fan 2 Speed Low Limit [200 RPM]
Extension Fan 2 Profile [Standard]
Extension Fan 3 Q-Fan Control [Auto]
Extension Fan 3 Q-Fan Source [CPU]
Extension Fan 3 Step Up [0 sec]
Extension Fan 3 Step Down [0 sec]
Extension Fan 3 Speed Low Limit [200 RPM]
Extension Fan 3 Profile [Standard]
Extension Fan 4 Q-Fan Control [Auto]
Extension Fan 4 Q-Fan Source [CPU]
Extension Fan 4 Step Up [0 sec]
Extension Fan 4 Step Down [0 sec]
Extension Fan 4 Speed Low Limit [200 RPM]
Extension Fan 4 Profile [Standard]
Extension Fan 5 Q-Fan Control [Auto]
Extension Fan 5 Q-Fan Source [CPU]
Extension Fan 5 Step Up [0 sec]
Extension Fan 5 Step Down [0 sec]
Extension Fan 5 Speed Low Limit [200 RPM]
Extension Fan 5 Profile [Standard]
Extension Fan 6 Q-Fan Control [Auto]
Extension Fan 6 Q-Fan Source [CPU]
Extension Fan 6 Step Up [0 sec]
Extension Fan 6 Step Down [0 sec]
Extension Fan 6 Speed Low Limit [200 RPM]
Extension Fan 6 Profile [Standard]
WATER PUMP+ Control [Disabled]
AIO PUMP Control [Disabled]
CPU Temperature LED Switch [Enabled]
Launch CSM [Enabled]
Boot Device Control [UEFI only]
Boot from Network Devices [Legacy only]
Boot from Storage Devices [Legacy only]
Boot from PCI-E/PCI Expansion Devices [Legacy only]
OS Type [Other OS]
Fast Boot [Enabled]
Next Boot after AC Power Loss [Fast Boot]
Boot Logo Display [Auto]
POST Delay Time [3 sec]
Bootup NumLock State [On]
Wait For 'F1' If Error [Enabled]
AMI Native NVMe Driver Support [Enabled]
Option ROM Messages [Force BIOS]
Interrupt 19 Capture [Disabled]
Setup Mode [Advanced Mode]
Boot Sector (MBR/GPT) Recovery Policy [Local User Control]
Next Boot Recovery Action [Skip]
Flexkey [Reset]
Setup Animator [Disabled]
Profile Name [1]
Save to Profile [1]
DIMM Slot Number [DIMM_A1]
Download & Install ARMOURY CRATE app [Enabled]

Hyper M.2X16 [Enabled] will cause the NVC issue. I replicated it by setting mine to enabled. Clean install Nvidia drivers should fix it. I have to try the clean install of the GPU drivers to verify it fixes it.

Edit just disabling Hyper M.2 solved it even without reinstalling the GPU driver for me. It just took a reboot.

Gotcha lemme try that

Edit : after 1 reboot seem normal but the nividia driver still was not registered until i logged into my acc

Edit 2: Just did factory reset of everything .. everything worked fine, boot within under 10 second . nividia driver registered. Only tried with 1 boot so far. Good news thus far

Also do you ever get a Patch file poping up after logging in ? Im trying to find out what is executing it . It only flashes for a second

Quote:

---

Originally Posted by nosam1g

Gotcha lemme try that

Edit : after 1 reboot seem normal but the nividia driver still was not registered until i logged into my acc

Edit 2: Just did factory reset of everything .. everything worked fine, boot within under 10 second . nividia driver registered. Only tried with 1 boot so far. Good news thus far

Also do you ever get a Patch file poping up after logging in ? Im trying to find out what is executing it . It only flashes for a second

---

Yeah it took a little bit after the first reboot for the Nvidia driver to initialize, after that it was normal.

That flash/pop up is the Armoury Crate apps. I disable it in bios and don't install it. I did try it but I don't use any of the apps in it so when I did a another Windows install I disabled it in the bios.

After 3 boot up everything is running good i think you figured it out man!!
Boot under 10 seconds.. Nividia registered upon logging in.
-Thank you bscool for the helping and everyone

Issue Resolved : Hyper M.2X16 [Enabled] needs to be disabled.

I do have one more question. Whenever i put my pc into sleep and i want to unsleep it .. the monitor does not come back, its just a black screen and my monitor flicks on and off orange .. anyone know of a solution ?

I think it is from the memory OC or high XMP. When I put mine back to default for the memory then it wakes like normal. I have noticed this on many different motherboards when running higher speed memory or really tight timings.

Even lowering my memory speed down to 4000mhz then it wakes from sleep fine. So I quite using sleep and just run my memory at higher speeds.