Search:

Type: Posts; User: syldon

Page 2 of 8 1 2 3 4 5

Search: Search took 0.01 seconds; generated 94875 minute(s) ago.

  1. Thread: PC wont boot up

    by syldon
    Replies
    11
    Views
    1,799

    Can you drop a dump of your bios settings? ...

    Can you drop a dump of your bios settings?


    Also, since you have so much options to swap out stuff try eliminating hardware problems. Run with one 1080ti for a little while, and then swap to the...
  2. Replies
    15
    Views
    3,998

    Sorry, it is 2x16 x2. It was just a post I found...

    Sorry, it is 2x16 x2. It was just a post I found while looking for another. I was certain someone had posted on the CH6 post with 64gb set up. I couldn't find it though. This one just came up in the...
  3. Replies
    15
    Views
    3,998

    I don't remember seeing anyone post a set up that...

    I don't remember seeing anyone post a set up that works with 4x16. There is a post regarding 2x2x16 that works though.




    Edited to correct memory size.
  4. Replies
    15
    Views
    3,998

    Elmor stated that for the CH7 2 x 16 is better a...

    Elmor stated that for the CH7 2 x 16 is better a long time back. I moved from the CH6 to the CH7. I used 4 x 8 on the CH6 with relatively few issues on earlier bios revision. On the later revisions I...
  5. Replies
    8
    Views
    6,283

    Qcode B4 is USB hotplug error. I think you...

    Qcode B4 is USB hotplug error. I think you already know this since you mentioned removing devices.

    Can you drop a txt dump of your bios settings. It is mostl likely down to voltages. Your system...
  6. The 2600 will run fine on the CH6E and yes there...

    The 2600 will run fine on the CH6E and yes there is a revision update to accommodate the 2600. You will have to use the flashback option before installing the CPU as the revision the board comes with...
  7. The reporting problem was nothing to do with the...

    The reporting problem was nothing to do with the 10c offset. Programmes are just misreading by a large amount. Hwinfo change log shows some of the issues that has been flying around.
  8. Asus (or AMD I don't know which) changed the...

    Asus (or AMD I don't know which) changed the reporting from certain sensors a little while back. The only software afaik that reports correctly is HWinfo.
  9. Auto does not default to enabled in all cases....

    Auto does not default to enabled in all cases. MIskew auto = disabled.
  10. Replies
    5
    Views
    1,196

    It is the normal boot cycle. The bios talks to...

    It is the normal boot cycle. The bios talks to each device in sequence. Memory is does not have the ultimate priority in succession. Motherboard devices > CPU > more motherboard devices > memory.

    ...
  11. Replies
    4
    Views
    3,902

    The raid driver is listed under the CH6 support...

    The raid driver is listed under the CH6 support page at the bottom.
  12. Replies
    1
    Views
    2,621

    I am fairly sure qcode is initialisation of the...

    I am fairly sure qcode is initialisation of the CPU. So the motherboard is having trouble getting any messages from the processor itself.

    Remove everything from the board and only connect the...
  13. Replies
    9
    Views
    1,488

    I added my specs to my profile. To add your...

    I added my specs to my profile.

    To add your own - look under settings and functions top right. Edit your details.
  14. Replies
    9
    Views
    1,488

    You bought some memory at two different points in...

    You bought some memory at two different points in time and they have sequential serial numbers? You really should be putting lottery tickets on; it is that region of lucky.

    The TL;DR totally agree...
  15. Replies
    9
    Views
    1,488

    I couldn't get 4X8 to run stable even at 3200. I...

    I couldn't get 4X8 to run stable even at 3200. I gave up and reduced to 2X8. I currently run at 3466. I have had quite a bit of experience with Ryzen memory OCing. I owned the CH6 more or less since...
  16. Most recorded with stability is 3466 on the CH6....

    Most recorded with stability is 3466 on the CH6. I was using 4X8 of B die rated at 4000Mhz. On 3502 revision I could hit 3466. Revisions after this, specifically those with spectre fixes and support...
  17. Replies
    5
    Views
    4,275

    I had a similar issue q code 8. Tried reflashing...

    I had a similar issue q code 8. Tried reflashing to all bios revisions, with the CPU in/out. Took all peripherals off including gfx and memory. Ended up RMAing and waited a few weeks for replacement...
  18. @xeromist I have only been replying to posts...

    @xeromist

    I have only been replying to posts here the last couple of days. And yes it has been on long posts. I did make copies of the text response and actually seen the text posted. Only to find...
  19. Replies
    15
    Views
    2,539

    Sorry couldn't help myself @gupsterg Thanks...

    Sorry couldn't help myself

    @gupsterg

    Thanks for the back to back comparison. I ran aida64 on a stability run just to push the temps up on this board. Vrms are idling at 33 and never go above...
  20. The forum keeps crashing when I try to post

    When I try to post or preview I keep getting an error message.

    Access Denied
    You don't have permission to access "http://rog.asus.com/forum/newreply.php?" on this server.
    Reference...
  21. Replies
    15
    Views
    2,539

    There really is no reason to upgrade if you have...

    There really is no reason to upgrade if you have a CH6:cool:
  22. Replies
    15
    Views
    2,539

    I can wait till July. Thanks for the heads up.

    I can wait till July. Thanks for the heads up.
  23. Editted my orignal statement. it didnt come out...

    Editted my orignal statement. it didnt come out well. I should have wrote "Use any of the following together to see the system crash Aida 64, hwinfo or Corsair link". I think some reported CPUz doing...
  24. CUE is working fine. It is programme that monitor...

    CUE is working fine. It is programme that monitor sensors that are crashing the system out. Usually when you use two at the same time. Try using Corsair link along with Aida64 or HWinfo if you want...
  25. Replies
    15
    Views
    2,539

    I have answered this post three times now, but...

    I have answered this post three times now, but the site keeps crashing out on my posting. I even copied the text to a txt file in case in crashed out a second time and saw a successful post. I am...
Results 26 to 50 of 198
Page 2 of 8 1 2 3 4 5