Search:

Type: Posts; User: Zarathustraa

Page 1 of 9 1 2 3 4

Search: Search took 0.04 seconds.

  1. Yeah, I shouldn't need the molex connector. ...

    Yeah, I shouldn't need the molex connector.

    For the 6 pin motherboard connector, EATX12V_3 in the manual, is a PCI-E 6 pin the right cable?
  2. Thanks. I'll just plug them all in other than the...

    Thanks. I'll just plug them all in other than the one needed for multiple graphics cards.
  3. Zenith Extreme Alpha II. I have one of those 64...

    Zenith Extreme Alpha II. I have one of those 64 core AMD processors. I'm just using it for cpu mining, and trying to save on power draw.
  4. Are the 8 pin and 6 pin power plugs required?

    I'm using the Dimm .2 slot with one nvme drive, overclocking a 64 core cpu, a low power graphics card, and overclocking the ram. I just have 1 SATA disk attached.

    Is EATX12V_1, EATX12V_2, and...
  5. Using GT-AX11000 in access point mode from another router.

    I have a firewall I'll be using as my router. I'm having some issues getting the router to behave well in access point mode with the firewall replacing it. Which port should be used for sending...
  6. How to connect to webgui of GT-AX11000 in access point mode?

    I just switched my AX11000 into AP mode. I can't seem to figure out how to connect to the admin UI. Previously, I have used router.asus.com:Port to login. I have tried 192.168.1.1:Port to get in too,...
  7. Problem screwing in Threadripper cpu on Zenith II Extreme Alpha.

    Pretty sure, I have a Foxconn socket. I have the cpu slotted in, and when I tighten the three screws in I don't hear the pop from the torque wrench. The screw starts refusing to move without applying...
  8. Replies
    3
    Views
    414

    How can I break into my own router?

    I only have a twenty character password, and have maybe up to six characters I am unsure of. A few of the characters might be other symbols that look similar. Since I know the position of the unknown...
  9. Replaced the battery. I saved out a txt file, and...

    Replaced the battery. I saved out a txt file, and not a com file. I can't find some of the settings.

    Do you know if settings such as:

    Disable Parity Workaround [Disabled]
    CMD Margins [40]
    ...
  10. Max pcie cards this board can support?

    I'm trying to figure out how many pcie cards I can slot into the board. Looking at it it looks like I could fit between 3 to 4 of these compute units I'm looking to add. The wrx80 would be ideal. Is...
  11. I should replace the battery anyways. I guess...

    I should replace the battery anyways. I guess when they get low stuff starts acting oddly. I have had the machine for five years, and it's about time. I am probably a few months away from losing a...
  12. Won't I lose my overclocking profile by pulling...

    Won't I lose my overclocking profile by pulling it?
  13. Board is occasionally taking me to bios update screen at boot.

    Sometimes, the system boots me into the bios update screen. I think it usually happens after power cycling. I boot into the screen and just reboot, as I don't have a bios set to load. Does anyone...
  14. Replies
    4
    Views
    504

    That should be fine. On their workstation board...

    That should be fine. On their workstation board they just mention a ten disk limit. I don't know if that is ten total, or just ten per RAID.
  15. Replies
    4
    Views
    504

    Oh, I'd just have RAID 0 on the plotting array....

    Oh, I'd just have RAID 0 on the plotting array. There's other storage attached that safe long term. The ideal build has like 10 nvme drives in RAID 0, and about eight 8 TB SATA III drives in raid 10...
  16. Replies
    4
    Views
    504

    Chia plotting rig

    I'm building a system for plotting Chia, and just have a few unknowns I need to resolve first. With the Asus WRX80 board how many nvme drives may I put in RAID 0? Can I raid drives together between...
  17. Replies
    354
    Views
    63,377

    Is bootable nvme raid 0 possible for Windows with...

    Is bootable nvme raid 0 possible for Windows with this board?
  18. Replies
    354
    Views
    63,377

    Does the DIMM.2 have 8 or 4 pcie lanes available ...

    Does the DIMM.2 have 8 or 4 pcie lanes available when two drives are installed?
  19. Awesome. So I can safely poke around if I'm...

    Awesome. So I can safely poke around if I'm careful to not damage the device in the process, meaning attach the serial cable properly.
  20. Does the warranty void sticker still matter?

    So, I have a router that is currently not functional. (ports and wireless do not work) I'm pretty sure it is an issue with a bad flash of the firmware. I can open the device up, and flash over the...
  21. Replies
    6
    Views
    3,740

    Well, I Yeah, I've gotten into recovery mode in...

    Well, I Yeah, I've gotten into recovery mode in the past. However, I cleared the nvram settings from the cfe page, and think some of the router values were lost. Pretty, sure a flag needed for...
  22. Replies
    6
    Views
    3,740

    Oh and there's no soldering involved. It should...

    Oh and there's no soldering involved. It should be safe to just flash back to stock this way, right?
  23. Replies
    6
    Views
    3,740

    Ok, I can connect wirelessly, but the lan ports...

    Ok, I can connect wirelessly, but the lan ports are not operational.
  24. Replies
    6
    Views
    3,740

    Believe I have bricked my rt-ac5300.

    I can't get the ac5300 to enter recovery mode. I've tried powering off and holding in the reset button, while powering back on, with no luck. I have also tried the wps button for the same results....
  25. You just need to play around with SHIM and MOK...

    You just need to play around with SHIM and MOK till you can get things working. I believe this should help, even if you're not using rEFInd. http://www.rodsbooks.com/refind/secureboot.html
Results 1 to 25 of 218
Page 1 of 9 1 2 3 4