Search:

Type: Posts; User: NemesisChild

Page 3 of 20 1 2 3 4 5 6

Search: Search took 0.03 seconds; generated 104699 minute(s) ago.

  1. Welcome to the forum! Is your CPU or memory...

    Welcome to the forum!

    Is your CPU or memory overclocked?
  2. Yes. here's what I suggest: 1.) Under Power...

    Yes. here's what I suggest:
    1.) Under Power Options in Windows CP, set it to performance
    2.) Open CPU-Z to monitor the CPU (Vcore) voltage to see what it uses at idle
    3.) Then run RealBench stress...
  3. Replies
    1
    Views
    708

    Welcome to the forum! Just update to the...

    Welcome to the forum!

    Just update to the latest and you should be good to go.

    Enjoy your new toy.
  4. Replies
    13
    Views
    10,937

    Hopefully the CPU wasn't damage due to extreme...

    Hopefully the CPU wasn't damage due to extreme thermal exposure.

    Good luck!
  5. Replies
    13
    Views
    10,937

    I'm surprised that it didn't shutdown after a few...

    I'm surprised that it didn't shutdown after a few seconds, you were lucky (or maybe not). I wouldn't suggest doing it again.

    Sounds like your problem happened after you installed the CPU cooler....
  6. Replies
    13
    Views
    10,937

    Welcome to the forum! Are you saying that you...

    Welcome to the forum!

    Are you saying that you tried to post without a CPU cooler installed?

    There shouldn't be much resistance or "pressure" when tightening down a HS. I would check the CPU...
  7. I don't agree about the design flaw theory. I've...

    I don't agree about the design flaw theory. I've been building PC's with ROG boards for many years going back to the Maximus V Formula.
    And most of the builds have been SLI with top of the line...
  8. There's the problem. Others have reported the...

    There's the problem. Others have reported the same issue here in the forums.

    I suggest contacting ASUS support and have them initiate an RMA for a replacement board.
  9. I suggest entering manual base timings,...

    I suggest entering manual base timings, frequency, and DRAM voltage in the bios.

    Have you tried increasing the DRAM voltage? Or played with the VCCIO and SA voltages?

    Also you can try Maximus...
  10. Thread: BIOS help

    by NemesisChild
    Replies
    2
    Views
    1,078

    Welcome to the forum! Did you load default...

    Welcome to the forum!

    Did you load default bios settings or clear the CMOS?

    You can reference your Ranger VIII manual for more info.
  11. Like I said previously, you have to use the bios...

    Like I said previously, you have to use the bios flashback feature to revert to an older bios.

    If the board doesn't have bios flashback, it can't be done.
  12. You have to use the bios flash back method to...

    You have to use the bios flash back method to revert to an older bios.
  13. Replies
    9
    Views
    3,447

    Must be a big secret, the web page is coming up...

    Must be a big secret, the web page is coming up "not found".
  14. What CPU cooler are you using? Remove it and...

    What CPU cooler are you using? Remove it and check the CPU socket closely for bent or broken pins.

    Did you try posting with one stick of RAM at a time and in different slots?
  15. https://www.easyuefi.com/resource/check-mbr-or-gpt...

    https://www.easyuefi.com/resource/check-mbr-or-gpt.html
  16. Replies
    48
    Views
    4,143

    It's best to dial in your CPU OC with manual...

    It's best to dial in your CPU OC with manual voltage. Once deemed stable, you can convert to adaptive mode.

    The offset/adaptive settings can be tricky, it usually takes a fair amount of time (and...
  17. Replies
    23
    Views
    4,338

    I personally have never used AIDA64. Have you...

    I personally have never used AIDA64. Have you tried RealBench?
  18. Replies
    23
    Views
    4,338

    Your SA voltage is high. I've tested numerous...

    Your SA voltage is high. I've tested numerous memory configurations. Best for me has been VCCIO (1.15v) and SA (1.20v).

    Keep the CR at 2T for better overall stability. You only get a marginal hike...
  19. Replies
    23
    Views
    4,338

    I easily OC'ed my 2x16GB 3200 CL14 set to 3400...

    I easily OC'ed my 2x16GB 3200 CL14 set to 3400 CL14 simply by just increasing the DRAM voltage to 1.375v.
    You have a good board and memory chip, so basically the CPU IMC would be your major...
  20. Replies
    23
    Views
    4,338

    Not sure what you're trying to achieve by pushing...

    Not sure what you're trying to achieve by pushing your memory that high.

    Essentially the sweet spot is 3200 CL14. Call it a day if you can do 3400 CL14. Higher than that will require looser...
  21. You do know that the max turbo freq for this chip...

    You do know that the max turbo freq for this chip is 4.7GHz right? So 4.7 really wouldn't be considered an OC.

    What was your actual Vcore while under full load?
  22. HX1000 is a solid PSU, but you're more than...

    HX1000 is a solid PSU, but you're more than likely on borrowed time at 10 years old.

    Keep in mind, a PSU will loose it's ability to provide consistent power to the rails over time. It will get...
  23. Replies
    104
    Views
    24,684

    This normal after a bios update. Just open up CAM...

    This normal after a bios update. Just open up CAM software and re-enable your RGB profile after the update.

    There's no need to have CAM startup on Windows.
  24. Replies
    17
    Views
    47,439

    Set it PCIe, it should automatically default to...

    Set it PCIe, it should automatically default to X4. You can verify the interface through Samsung Magician software.

    Yes, install the Samsung NVME driver, it's faster than the generic MS driver.
  25. Replies
    104
    Views
    24,684

    They never state what are, it's apparently a big...

    They never state what are, it's apparently a big secret.
Results 51 to 75 of 497
Page 3 of 20 1 2 3 4 5 6