Search:

Type: Posts; User: HalloweenWeed

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Be careful, choose one that is compatible W/RIVE....

    Be careful, choose one that is compatible W/RIVE. There is one top model that is not compatible (search this forum for the model to find out).
  2. Are you planning on going to Haswell-E? This...

    Are you planning on going to Haswell-E? This autumn? I know I will not be able to afford :(
    I would however, watch your results.


    No. Voltages are pretty close, except for the new low-V RAM...
  3. All in all though, Raja is correct (as always)....

    All in all though, Raja is correct (as always). Your timings were so tight that the increase in memory speed with the timings specified by Corsair will not net much gain in performance, definately...
  4. Yeah the economy has hit me hard too, and a work...

    Yeah the economy has hit me hard too, and a work loss due to serious illness in the past has been what we call a "double-whammy" here in the USA, meaning something like two hard hits in one. But our...
  5. Maybe a 1*C rise in temperature, but that's...

    Maybe a 1*C rise in temperature, but that's within margins of error of measurement too; dust buildup is likely to cause more rise in temperature than what may occur from increasing VCCSA. VTT could...
  6. Sandro: With the last generation CPUs, which are...

    Sandro: With the last generation CPUs, which are very similar to ours in comparison to the previous generations, it was common for users to set VTT 1.4 - 1.45V for the faster memory kits, of the same...
  7. Sandro I would not recommend anything risky...

    Sandro I would not recommend anything risky without saying it was risky. My recommendations above are well within the forum accepted ranges. VTT & VCCSA 1.325V is not risky.
  8. Try increasing VTT & VCCSA to 1.325V with the...

    Try increasing VTT & VCCSA to 1.325V with the above settings I recommended
  9. I am only setting what is recommended by the XMP...

    I am only setting what is recommended by the XMP table, for the majority of settings.
  10. Sandro no wonder your memory was not working up...

    Sandro no wonder your memory was not working up to full speeds.
    Try these settings to get your mem to 2176-2240

    Extreme Tweaker menu:
    Ai Overclock tuner: Manual
    Memory freq: DDR3-2176-2240
    ...
  11. Replies
    48
    Views
    25,723

    Press a "clear CMOS" button

    Press a "clear CMOS" button
  12. Ooh, bleeding energy when the CPU idle (and not...

    Ooh, bleeding energy when the CPU idle (and not sleeping).
  13. Replies
    21
    Views
    7,929

    I don't know. I was just thinking maybe you never...

    I don't know. I was just thinking maybe you never checked your CPU socket screws, but you did. The thing is, if they were tightened to the point that the board cracked, they might not feel too tight...
  14. I'm sorry, Sandro. I thought MemTweakIt read the...

    I'm sorry, Sandro. I thought MemTweakIt read the SPD XMP tables in your RAM, but instead it reads the BIOS settings. So MemTweakIt will not help here. You could also check the Asus "SPD information"...
  15. Just a note of Sandro's orig. post that...

    Just a note of Sandro's orig. post that precipitated this thread, it details the goal:



    Sandro only needs to get to DDR3 2240 as she/he sets Bclck to 102-105. This has the effect of making 2133...
  16. Ah, there we go. Yes Sandro, that's what I need....

    Ah, there we go. Yes Sandro, that's what I need. I will post with settings, but it might be a day or so, I am very busy for a short while.

    Ah, ce ne andiamo. Sì Sandro, che è quello che mi serve....
  17. Sandra may be available in Itialian Sandra può...

    Sandra may be available in Itialian

    Sandra può essere disponibile in Itialian

    http://www.sisoftware.net//?d=dload&f=sware_dl_3264&l=it&a=
  18. Sandro, did you not understand post #3? I need...

    Sandro, did you not understand post #3?
    I need you to install and run Memory Tweaker, AIDA64, or (SiSoft) Sandra (http://www.sisoftware.net/) and show me the results (do not do all of them, only...
  19. No Sandro, Asus does not include the RC option in...

    No Sandro, Asus does not include the RC option in the BIOS.
    We need: tCL, tRCD, tRP, tRAS, tRFC, tRRD, tWR, tWTR,& tRTP
  20. You will need the 1066MHz timings

    You will need the 1066MHz timings
  21. If the DRAM current capability (130-140) increase...

    If the DRAM current capability (130-140) increase does not help, you will need to get all the RAM timings off the RAM XMP tables from a utility such as Memory Tweaker, AIDA64, or Sandra. You...
  22. FYI everybody else: Sandro's translation software...

    FYI everybody else: Sandro's translation software has translated the word to "car" instead of "auto."
  23. Replies
    11
    Views
    12,714

    Nope. Leave it on.

    Nope. Leave it on.
  24. Replies
    21
    Views
    7,929

    EVGA had the same prob W/CPU socket screws on the...

    EVGA had the same prob W/CPU socket screws on the X58 line boards circa 2010. Tightening the screws too tight warps the board too much, possibly causing hairline fractures too. When the hairline...
  25. Wow, we have seen a lot of this complaint lateley...

    Wow, we have seen a lot of this complaint lateley on this forum, the prob is the complaints are usually involving RIVBE.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4