Search:

Type: Posts; User: Silent Scone@ROG

Page 6 of 20 FirstFirst 3 4 5 6 7 8 9

Search: Search took 0.02 seconds; generated 114510 minute(s) ago.

  1. You can play with values up until around 1.5v....

    You can play with values up until around 1.5v. Beyond this is poor tuning and unsuitable for daily use.
  2. But what is the stop code?

    But what is the stop code?
  3. Hello, It's definitely memory training. A cold...

    Hello,

    It's definitely memory training. A cold boot issue ranging across different vendors and boards is just users struggling to dial in memory kits to a point where they are stable enough to...
  4. Replies
    1
    Views
    302

    Hello, Enter the UEFI and enable XMP Profile....

    Hello,

    Enter the UEFI and enable XMP Profile. This sets the parameters for the frequency and timings set by the memory vendor.
  5. What have you done in an effort to tune the...

    What have you done in an effort to tune the memory? Key rails on this platform are VCCSA and VCCIO. As these are signal rails methodical testing can sometimes be needed depending on the CPU (more...
  6. Hello, What are you using to test memory...

    Hello,

    What are you using to test memory stability?
  7. Hello, more voltage is often required when using...

    Hello, more voltage is often required when using an adaptive voltage due to accounting for load transitioning.
  8. Enabling DOCP will scale the FCLK automatically.

    Enabling DOCP will scale the FCLK automatically.
  9. Hello, you likely need to tune SOC voltage. Check...

    Hello, you likely need to tune SOC voltage. Check what the auto rules are applying and then increase from there. The double boot is due to failing memory training as the overclock isn't stable.
  10. Hello, 4 DIMMs should not be an issue. If the...

    Hello, 4 DIMMs should not be an issue. If the instability is due to overclocking the infinity fabric clock, you'd need to dial that out. I'm running a 5950X with 4x8GB @ 3733 CL14.

    You can try...
  11. Have you checked event viewer to see if there's a...

    Have you checked event viewer to see if there's a stop code reported?
  12. Replies
    1
    Views
    401

    Hello, Will need a little more context than...

    Hello,

    Will need a little more context than that...

    Use USB Flashback in order to revert safely to an older UEFI revision.
  13. Hello, The system will hit TJ MAX long...

    Hello,


    The system will hit TJ MAX long before any damage will occur. You can set an alert in something such as HWINFO for when the pump drops below a certain RPM.

    87764
  14. Firstly, revert to Optimised Defaults and see if...

    Firstly, revert to Optimised Defaults and see if the issue persists. It's probable the crashes are being caused by instability of the infinity fabric (FCLK). Establish if the crashing still occurs at...
  15. Redownload the file from the support site and use...

    Redownload the file from the support site and use USB Flashback after renaming the CAP to M12E.CAP
  16. Sounds more like something on your system is...

    Sounds more like something on your system is causing the service to halt. Report the issue in GPUT III on Discord here: https://discord.gg/7SDse2t
  17. Hello, The performance delta between 16x and...

    Hello,

    The performance delta between 16x and 8x lane speed is normally within margin of error.
  18. Replies
    595
    Views
    190,216

    Hello, updates for additional rebar support are...

    Hello, updates for additional rebar support are in the pipeline. Worth pointing out, unless you're using an AMD GPU, it's not even possible to reap any benefits by enabling SAM support at this time...
  19. Hello, where are you seeing these temp sensors?...

    Hello, where are you seeing these temp sensors? Sounds like you're looking at third party software. Short of contacting the vendor, you can probably open HWInfo and simply cross reference them, as...
  20. Replies
    28
    Views
    7,111

    Provide feedback here https://discord.gg/7SDse2t

    Provide feedback here https://discord.gg/7SDse2t
  21. Replies
    3
    Views
    368

    Hi, 1) Which motherboard and CPU 2) Are you...

    Hi,

    1) Which motherboard and CPU

    2) Are you running the latest UEFI

    3) Which memory kit PN
  22. Make sure you're using the latest chipset drivers...

    Make sure you're using the latest chipset drivers and use Samsung Magician to check for the latest firmware on the NVME drives.
  23. Hello, Q-CODE 0D is memory training. Some...

    Hello,

    Q-CODE 0D is memory training.

    Some kits may require more voltage due to the guard band put in place by the memory vendor not being adequate for other platforms. You can try 1.4 to 1.45v...
  24. Hello, Are you able to provide the URL you...

    Hello,

    Are you able to provide the URL you were using?
  25. Hello, 1) I would recommend using Karhu Ram...

    Hello,

    1) I would recommend using Karhu Ram Test over HCI. Far easier to use and more stringent test of stability.

    2) First gen Ryzen Fabric is not as strong as later iterations, frequency is...
Results 126 to 150 of 500
Page 6 of 20 FirstFirst 3 4 5 6 7 8 9