Search:

Type: Posts; User: kaese

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. I dont know the reason but first thing I would do...

    I dont know the reason but first thing I would do is: switch back to your first BIOS (that one you updated manually to 3701) and do a BIOS reset (disconnect power cables and take out BIOS battery for...
  2. Replies
    3
    Views
    1,721

    Did you overclock your Bclk? It could also be a...

    Did you overclock your Bclk? It could also be a problem from using a Bclk other than 100 MHz. If so, try with it set to 100 MHz.
  3. Replies
    10
    Views
    5,460

    Good news - the programmer EZP2010 finally...

    Good news - the programmer EZP2010 finally arrived and I could revive the dead BIOS chip :-).
    Because I am curious, I used the copy function BIOS2-->BIOS1 again. And guess what - it bricked the chip...
  4. As already stated it probably needs some tweaking...

    As already stated it probably needs some tweaking to get your salad bowl of RAM sticks working. Still you wont have quad channel bandwidth so it is not preferred. Of course it always depends on your...
  5. Replies
    6
    Views
    2,097

    You should not boot without any cpu cooler...

    You should not boot without any cpu cooler attached, a couple of seconds with the water cooler block but without water flow should be fine however.
    Before rebooting I advise you to clean any coolant...
  6. Replies
    0
    Views
    431

    Shut-down system when CPU fan stops

    Hey I would like to configure my system in such manner that a shut down is initiated when the CPU fan speed goes to 0.
    Background: Actually I use water pump that generates a fan speed signal on the...
  7. Replies
    10
    Views
    5,460

    Thanks Korth, I am going to order a W25Q128*...

    Thanks Korth,
    I am going to order a W25Q128* then - however I still have a doubt about buying the right model:
    According to this page https://www.elnec.com/en/device/Winbond/W25Q128FV/ the part...
  8. Replies
    10
    Views
    5,460

    Yes that a great idea: I am paranoid enough to...

    Yes that a great idea: I am paranoid enough to write secure the chip with a hardware mod... ;-)
    However I do not find the W25Q128FVSIG in DIL format only SO package - where can I get the DIL package?
  9. Replies
    10
    Views
    5,460

    Sorry to hear that and thanks for the reply...

    Sorry to hear that and thanks for the reply buddy. I will order a new chip then.



    I will try the switches on the weekend and report afterwards (however, as I am not even getting errorcodes but...
  10. Replies
    10
    Views
    5,460

    BIOS 1 - Boot loop with Q-code 00

    Honestly I partly bought the Rampage V because BIOS flashing seemed extraordinarily stable with the extra features (2 BIOS ICs, flashback, BIOS copy function).
    However, after having flashed one BIOS...
  11. Make sure your BCLK is set to 100 MHz and rerun...

    Make sure your BCLK is set to 100 MHz and rerun benchmark.
  12. Replies
    1
    Views
    709

    5820K OC: rock stable only up to 12 threads

    Hello guys I have an interesting behaviour on my System (CPU 5820K@4.5 GHz, RAM 2600 MHz 64GB in 8 banks, 100 strap).
    Running 12 threads is definitely rock stable (running over 1000 hours without...
  13. Replies
    5
    Views
    13,311

    Thanks enyceedanny the CSM did do the trick! The...

    Thanks enyceedanny the CSM did do the trick! The USB pen drive has FreeDos and apparently has no UEFI drivers.

    Still I wonder if there is a way to get to see an error message.
  14. Replies
    5
    Views
    13,311

    Boot from USB problem

    Hey guys,

    I want to boot from an USB device so i created a bootable USB device (FreeDos).
    When I select the boot override menu (F8) I see, and chose the respective USB stick from the menu....
  15. Replies
    5
    Views
    2,602

    ....technically when you run your RAM at 3000 MHz...

    ....technically when you run your RAM at 3000 MHz you are overclocking the CPU (its memory controller) and your CPU will typically require a higher voltage.
    1.249 V seems a little high though -...
  16. Replies
    3
    Views
    1,745

    Most often this is a RAM issue (having 24 GB of...

    Most often this is a RAM issue (having 24 GB of RAM is kind of odd probable you are mixing different kits). Try with one RAM stick set to 2133 MHz.
  17. Replies
    150
    Views
    65,839

    I just updated from 2101 to 3301 - it took about...

    I just updated from 2101 to 3301 - it took about 10-15 reboots and runs now perfectly fine, even with the very same OC settings.
  18. Replies
    18
    Views
    5,613

    Lets have a look at the numbers:...

    Lets have a look at the numbers:
    P=c*dV/dt*\rho*\Delta T
    where P is the power of the system during stress test and \Delta T the increase of cooling liquid temperature after passing through all...
  19. Replies
    18
    Views
    5,613

    It seems a little high to me too. I use a...

    It seems a little high to me too. I use a Watercool HEATKILLER® MB-X VRM ASUS RAMPAGE V EXTREME NI cooler and can hardly reach 40C during stress testing.
    However it is the first device in my...
  20. Replies
    19
    Views
    8,752

    Do a BIOS Reset (take out battery and unplug...

    Do a BIOS Reset (take out battery and unplug power for a minute). Boot into BIOS 1901, there you can copy the 1901 BIOS to the other chip (takes a couple of minutes).
  21. Replies
    6
    Views
    2,289

    Can you provide more information on your water...

    Can you provide more information on your water circuit? If you cool first the GPU and then the VRM, you are "cooling" the VRM with hotter water....
    I have the VRM under water (and the VRMs are the...
  22. Try running a single kit of your 2800 MHz RAM at...

    Try running a single kit of your 2800 MHz RAM at 2666 MHz.
  23. -deleted-

    -deleted-
  24. For easiest (and probably highest) OC you should...

    For easiest (and probably highest) OC you should use in any case one kit of four modules.
  25. Replies
    41
    Views
    10,717

    I experienced the full range of different q-codes...

    I experienced the full range of different q-codes when my CPU died... And I dont see a pattern that would unambigeously point to the RAM or anything in your codes so may also think of that option.
Results 1 to 25 of 65
Page 1 of 3 1 2 3