Search:

Type: Posts; User: Falkentyne

Page 1 of 10 1 2 3 4

Search: Search took 0.01 seconds.

  1. Your board has an onboard power button. What...

    Your board has an onboard power button.
    What happens if you use the onboard power button instead of the case power supply button?

    What happens if you disconnect the "RESET" pins on the...
  2. Microcode 15 works in 2004 if you delete the...

    Microcode 15 works in 2004 if you delete the other microcodes and insert it. AVX512 works. bscool has it modded already.
    Just don't expect raptor lake to work if you delete all the microcodes.
    ...
  3. No one answers because no one knows the answer to...

    No one answers because no one knows the answer to your question. You're asking a very difficult, sweaty question.

    No one can tell you what the 'safe' voltage is for 1 core loaded. I'm still...
  4. You can reduce the PCH temps by swapping the...

    You can reduce the PCH temps by swapping the thermal pad with something like a Gelid Ultimate pad. Unfortunately I don't know the proper thickness, but it's more than 2mm. Might require you to...
  5. E cores being put to sleep will of course give...

    E cores being put to sleep will of course give you higher vcore under load, because there is less current (amps), so the voltage will drop less from the BIOS voltage setting. But since the P cores...
  6. The BIOS consists of multiple regions (Four which...

    The BIOS consists of multiple regions (Four which can be easily grouped and enumerated independenetly), not all which are flashed on the bios chip itself! It's THOSE regions which can give you a bad...
  7. Can you use a normal USB C device in that port?...

    Can you use a normal USB C device in that port?
    if nothing is detected at all, you need to flash the 2x2 USB firmware that should be available on the Asus support page for that motherboard.
  8. You can ignore this error. I used to know why it...

    You can ignore this error.
    I used to know why it occurs but I forgot. Someone posted why it happens on OCN awhile ago.
    But it's some sort of BIOS setting which triggers it when windows loads.
  9. Replies
    9
    Views
    1,693

    There was some discussion about this. Apparently...

    There was some discussion about this.
    Apparently a fix to this is, when changing memory or even CPU overclock settings, to save, go back to BIOS, turn off the system and then completely remove the...
  10. That's for fixed vcore. The old "override" mode...

    That's for fixed vcore. The old "override" mode if you don't want to use by core usage or similar. Sets cpu voltage directly to the VRM and ignores VID, AC Loadline, etc. So if you wanted...
  11. I tested Sleep (S3?) on my Maximus Extreme just...

    I tested Sleep (S3?) on my Maximus Extreme just now on 1304 and it resumed fine after a minute or so of sleep.
    RTX 3090 FE with fast boot disabled.

    Isn't Qcode 97 an error with VGA/video BIOS...
  12. Bios 1302 was released a few days ago. You can...

    Bios 1302 was released a few days ago. You can try that.
    Remember--before running EZflash, ALWAYS go to the right most menu and choose "Load optimized defaults", save and exit. Then after you are...
  13. Sticky: Hi Papusan, The top m.2 on board, afaik is a...

    Hi Papusan,

    The top m.2 on board, afaik is a PCIE 5.0 slot, runs off the CPU and will drop your GPU in the primary PCIE to 8x speed if installed. If Gen 5 PCIE 5.0 NVME drives ever come out,...
  14. Replies
    81
    Views
    10,361

    Obviously, the instant slam dunk test is to ship...

    Obviously, the instant slam dunk test is to ship the CPU, motherboard, storage, PSU, RAM And video card to the retailer and have them test those 6 components together in the same identical...
  15. Replies
    7
    Views
    5,043

    I think you should read my post again instead of...

    I think you should read my post again instead of choosing to read the words you want to acknowledge.
    Your case came out in 2011.

    USB type C wasn't even a thing in 2011. How are you supposed to...
  16. Replies
    5
    Views
    1,729

    As Scone said, 6400 mhz on 4 dimm boards is very...

    As Scone said, 6400 mhz on 4 dimm boards is very difficult, and you get into a problem where it's stable on one boot and not on the next.
    Sometimes adjusting "slopes" and skews can help this....
  17. Replies
    13
    Views
    7,954

    It's a standard PCIE (video card) 6 pin cable...

    It's a standard PCIE (video card) 6 pin cable (without the 6+2 pin). Any video card PCIE cable will work.
  18. Can you link me to the exact camera that you're...

    Can you link me to the exact camera that you're using?
  19. Try lowering the VRM Switching frequency in...

    Try lowering the VRM Switching frequency in Digi+VRM.
  20. Sticky: Yes they are identical. Version numbers aren't...

    Yes they are identical.
    Version numbers aren't stealth changed. Any changes are put in a new number (e.g. 812 would be a bugfix for 811, etc).
  21. Replies
    4
    Views
    532

    Please read the motherboard manual. It's there...

    Please read the motherboard manual. It's there for a reason.
    The 2nd PCIE slot will never run at x16. When populated it will run at x8 (shared with PCIE slot 1 x8).
    Lane configuration is x16/x0...
  22. Sticky: That guy is a troll. Just put him on block. ...

    That guy is a troll. Just put him on block. He's making posts all over the interwebs spamming nonstop about his precious DDR5 mismatched issues. Maybe if everyone mutes him he might realize...
  23. Did you try changing this setting in your BIOS: ...

    Did you try changing this setting in your BIOS:

    PCI Express Native Power Management: To disabled (instead of auto?)
  24. This precise WHEA error (Device ID 7AB4) can be...

    This precise WHEA error (Device ID 7AB4) can be fixed by setting PCI Express Native Power Management---to disabled in the advanced PCI Express settings.
    It's unclear at this point if this is a BIOS...
  25. Sticky: Peter is one of the chief engineers at Asus. He...

    Peter is one of the chief engineers at Asus.
    He was formerly known from his DFI days, where he put in so much work on the legendary DFI Lanparty series, around the time when Abit was going bankrupt...
Results 1 to 25 of 243
Page 1 of 10 1 2 3 4