Search:

Type: Posts; User: feedmeink

Page 2 of 8 1 2 3 4 5

Search: Search took 0.01 seconds; generated 31114 minute(s) ago.

  1. Replies
    9
    Views
    289

    Thanks!

    Thanks!
  2. Replies
    9
    Views
    289

    Case advice for two systems

    I'm looking for a case that can support two seperate systems and excessive watercooling options. Considering building a table. Am I bound to two seperate cases?
  3. Replies
    9
    Views
    734

    Nvm I see you have the rampage vi extreme I...

    Nvm I see you have the rampage vi extreme
    I have same mobo. Let me know if you have any specific questions. I spent countless days and hours experimenting with that bios and feel very confident...
  4. Replies
    9
    Views
    734

    I have 7980xe delided with liquid metal. If you...

    I have 7980xe delided with liquid metal. If you want to know stock voltages, save bios profile, switch back to stock bios, test and record voltages you see in hwinfo64, then revert to your new bios...
  5. Nvm, it was the c-states. Still slightly higher...

    Nvm, it was the c-states. Still slightly higher idle temps. I'm sure the new update optimizes differently. 3-5c increase in idle temps. Max temps the same.
  6. Bios update idle temps higher than previous

    I am watercooling with custom loop. After bios update idle temps went from 23c to 30. I am running in adaptive mode. What should I set minimum power percentage to in windows power plan. Currently...
  7. Congrats on the new system. As far as testing...

    Congrats on the new system. As far as testing memory I highly recomend using RAMTEST and memtest pro for checking stability. Ramtest can also stress your cache for the cpu. I definitely would use...
  8. Just a follow up, do not change original voltage...

    Just a follow up, do not change original voltage for state 1. For some reason was getting black screens. Changed from 930 to 900 and runs fine now. I think it complains when first state is...
  9. Replies
    1
    Views
    1,141

    I have vega 56, but this applies to both 56 and...

    I have vega 56, but this applies to both 56 and 64. Rule of thumb for these cards. Memory voltage is actually linked to frequency voltage. Buildzoid did a video on this and verified with probing...
  10. For anyone that has this question, I finished...

    For anyone that has this question, I finished fine tuning each P state on the vega 56. This would apply for vega 64 as well. First I left all states at stock. Overclocked the memory with hwinfo...
  11. Vega 56 2019 software allowing all p-state adjustments

    When I originally got my vega56 I put it under water and did the basic overclock on state 6 and 7. Been focusing on memory fine tuning and cpu tuning. Found out in the 2019 version of wattman it...
  12. Have you monitored temperature? Try using hwbot...

    Have you monitored temperature? Try using hwbot and look at cpu temp (per core) and gpu temp. Just to rule anything out.
  13. Your fluid temperature is mainly a reflection of...

    Your fluid temperature is mainly a reflection of radiator thickness and space along with good fans. I have 47mm thick rads with high rpm fans running at 30% to keep extra quite. I run a i9 7980xe...
  14. Cpu header will only adjust fan curve based on...

    Cpu header will only adjust fan curve based on cpu temp. For gpu fan curve, my only suggestion is to get a temperature fitting. It monitors the temperature of the water as it passes through the...
  15. Look up lian-lee pc-011 dynamic

    Look up lian-lee pc-011 dynamic
  16. Replies
    1
    Views
    250

    Have you fully updated the bios?

    Have you fully updated the bios?
  17. Replies
    4
    Views
    250

    This is normal variation

    This is normal variation
  18. Replies
    5
    Views
    874

    Not sure if you have done this, but if you are in...

    Not sure if you have done this, but if you are in adaptive, you want to enable c-state. When manual you want to disable c-state. If it truly is a v-droop issue, try adjust LLC lower. The higher...
  19. Thread: Radeon vii

    by feedmeink
    Replies
    6
    Views
    1,608

    I'm into 3D rendering and gaming. Was...

    I'm into 3D rendering and gaming. Was considering upgrading, but I might hold off till next launch. Unless its straight fun to overclock. For the price point it doesn't seem too bad.
  20. Thread: Radeon vii

    by feedmeink
    Replies
    6
    Views
    1,608

    It's unfortunate they released this card with so...

    It's unfortunate they released this card with so many software issues. Expected better from them. Once they resolve issues and we can see a propper overclock can picture 2080ti performance. The...
  21. Replies
    4
    Views
    237

    To get a better idea, you can stress test with...

    To get a better idea, you can stress test with aida64 cpu only, just to make sure it isn't the game using primarily those cores. Aida64 will put full load on all cores at once so you can monitor...
  22. Replies
    4
    Views
    237

    Yeah, it should. I wouldn't blame you for not...

    Yeah, it should. I wouldn't blame you for not wanting to lap the ihs. Hold onto that screenshot incase they want proof. Just tell them three cores run extremely hot and you want a replacement. ...
  23. Replies
    4
    Views
    237

    It sounds like either the ihs on the cpu is...

    It sounds like either the ihs on the cpu is concave, or it is not making decent contact with the thermal paste. Take the cpu out and try and spin on your table. If it spins, might be a good idea to...
  24. Thread: Radeon vii

    by feedmeink
    Replies
    6
    Views
    1,608

    If they unlock the power limitations, maybe it...

    If they unlock the power limitations, maybe it would be comparable to the 2080ti if at stock it meets 2080 spec. Should be interesting to see
  25. Replies
    10
    Views
    394

    Also m.2 under the cover stays between 30 and...

    Also m.2 under the cover stays between 30 and 50c. Although I have bottom intake, so first thing it pushes over is the bottom of the motherboard
Results 26 to 50 of 177
Page 2 of 8 1 2 3 4 5