Search:

Type: Posts; User: feedmeink

Page 4 of 8 1 2 3 4 5 6 7

Search: Search took 0.01 seconds; generated 28887 minute(s) ago.

  1. Not sure why I said xeon. I think i mixed two...

    Not sure why I said xeon. I think i mixed two posts together in my brain haha
  2. Looked up the extreme on new egg for giggles. ...

    Looked up the extreme on new egg for giggles. Aparently it is so rare sellers are trying to get rid of for up to 1,700 USD. What is going on? Haha
  3. Replies
    350
    Views
    12,145

    Nah, I didn't skip reading. I was saying earlier...

    Nah, I didn't skip reading. I was saying earlier it didn't have a negative effect for me using the original ihs. But I figured it would be a fun test. The ihs will be here Saturday. Gonna take...
  4. I'm assuming the top box that reads 48x means you...

    I'm assuming the top box that reads 48x means you have set to 4.8 on all cores. Not sure about the 8 vs 120. Never worked with a xeon chip.
  5. Replies
    350
    Views
    12,145

    decided to ditch the monoblock for personal...

    decided to ditch the monoblock for personal testing. Ordered a copper ihs that is supposed to make up the difference in thickness after LM delid. Ordered an ek velocity cpu block, and vrm block by...
  6. Replies
    8
    Views
    447

    Oops, yeah, it was a typo. 1.17volts! Ooopsy :D

    Oops, yeah, it was a typo. 1.17volts! Ooopsy :D
  7. Replies
    8
    Views
    447

    7980xe here. Rampage vi extreme board. 4.6ghz...

    7980xe here. Rampage vi extreme board. 4.6ghz at 1.17volts. Can get to 4.9 1.3 but best to stay below 1.2 for everyday use. This board sucks for ram in my opinion. I'm using 4000mhz corsair...
  8. I read that article too. You gotta be careful...

    I read that article too. You gotta be careful when reading that stuff. Half the time people have other issues going on unrelated to the cpu. I think they have a different issue. The only viable...
  9. I do not have this cpu, but I constantly read up...

    I do not have this cpu, but I constantly read up on new tech. This cpu does not support hyper threading. Some have said the stuttering stops when you disable hyper threading in bios. Some mobos...
  10. Replies
    2
    Views
    1,262

    I don't see why not. I think my problem was...

    I don't see why not. I think my problem was because it was set in offset mode. I went back in and entered manual voltage. It worked fine. You can try that. Hope this helps.
  11. Replies
    350
    Views
    12,145

    Please update with OC and thermal difference...

    Please update with OC and thermal difference after you direct die. I'm very interested in seeing the difference.
  12. Replies
    350
    Views
    12,145

    Can't beat direct die. I'm sure it will work out...

    Can't beat direct die. I'm sure it will work out good. I've never done direct die before. Been too paranoid I would crack the PCB lol. Plus I see a lot of complaints about the LM not reacting...
  13. Replies
    350
    Views
    12,145

    I run 4.6 at 1.17 and 4.8 at 1.23. I prefer to...

    I run 4.6 at 1.17 and 4.8 at 1.23. I prefer to stay below 1.2 so I backed it down. I dunno. I really don't have any problems
  14. Replies
    350
    Views
    12,145

    I dunno. I noticed a huge improvement after...

    I dunno. I noticed a huge improvement after delid. Variance is minimal. Same board and monoblock 7980xe. The contact area is definitely large enough. Contact seems good. I know you are set on...
  15. Replies
    4
    Views
    653

    Try not using xmp. Manually set timings to the...

    Try not using xmp. Manually set timings to the sticker on the sticks and voltage. Try vccio 1.15 and vccsa 1.1. If this doesn't work, try setting to 2T instead of 1T.
  16. If encoding a blu ray utilizes avx, it could be...

    If encoding a blu ray utilizes avx, it could be that. Of your offset for avx equals 4.6 that would explain it. To rule it out, try using aida64 or something similar without using avx function and...
  17. I would set bus speed to 100 and go for 3600...

    I would set bus speed to 100 and go for 3600 first. Try leaving the timings the same and see if it boots. Of it wont, loosen up the timings a bit or set to 2t timing. If that doesn't work,...
  18. Replies
    15
    Views
    783

    Thanks!!!

    Thanks!!!
  19. Replies
    6
    Views
    414

    I have same board with 7980xe. Have spent...

    I have same board with 7980xe. Have spent countless hours playing with ram. I am stable at 3600. Can you list what vccio voltage and system agent voltage you are using? What is your current dram...
  20. Replies
    15
    Views
    783

    Glad that worked! Enjoy!

    Glad that worked! Enjoy!
  21. Replies
    15
    Views
    783

    Have you checked windows power settings? I had...

    Have you checked windows power settings? I had to adjust mine from 80% to 100%. I'm not sure, but this may only apply for adaptive voltage.
  22. Replies
    7
    Views
    354

    I doubt I'll test this theory out haha

    I doubt I'll test this theory out haha
  23. Replies
    7
    Views
    354

    Irrational fear

    I have a custom waterloop with fan intake at the bottom of the case. Yesterday I was drinking a beer and set it next to the case. Couldn't help but Invision me spilling the beer and my 3,000 rpm...
  24. Replies
    18
    Views
    861

    Manual is typically more reliable for...

    Manual is typically more reliable for benchmarking. I agree about adaptive. There are very few guides that get into adaptive mode. To me it just makes sense to be in adaptive. Why milk the power...
  25. Replies
    18
    Views
    861

    I can only speak for myself. Different mobo and...

    I can only speak for myself. Different mobo and cpu. I use x299 platform. I believe in manual mode you disable c-states. In adaptive you enable c-states. I did per core offset in negative...
Results 76 to 100 of 178
Page 4 of 8 1 2 3 4 5 6 7