Search:

Type: Posts; User: Silent Scone@ASUS

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. XMP I is the validated board profile that you...

    XMP I is the validated board profile that you will have seen on past generations. Every time a board is validated, this profile is the one used by the memory vendor and ASUS. On Z390, there is now...
  2. Assuming you're both receiving the Mem O.K...

    Assuming you're both receiving the Mem O.K message, then both of you.
  3. Looks like MEM O.K. You can disable the switch...

    Looks like MEM O.K. You can disable the switch located on the board. Might want to check memory stability, too. The function kicks in when POST stress tests fail.
  4. Hello, The Encore is the better board, hence...

    Hello,

    The Encore is the better board, hence why it's priced above.

    I have linked you to the product comparison tool.
    ...
  5. Some builds can simply favour certain CPUs over...

    Some builds can simply favour certain CPUs over others, as no two CPU are identical. If the system was working fine on the previous build, it's safe to leave it. Or, you can dial out the instability...
  6. XMP II is the memory vendor profile, which tends...

    XMP II is the memory vendor profile, which tends to have looser sub timings than the optimised board profile (XMP1). Your new CPU likely has a slightly weaker IMC.
  7. Should be fine, although ratios above 3600 can...

    Should be fine, although ratios above 3600 can sometimes require manual tuning depending on the CPU and memory kit. Be sure to try with Maximus Tweak Modes if experiencing difficulty.
  8. Hello, Reseat both the CPU and memory modules,...

    Hello,

    Reseat both the CPU and memory modules, whilst checking for even mounting pressure when reattaching the cooler.
  9. Still sounds like memory instability. Subsequent...

    Still sounds like memory instability. Subsequent clear of the UEFI / flash probably cleared whatever was stuck in NVRAM.
  10. Hello, the QVL is old as the motherboard is...

    Hello, the QVL is old as the motherboard is fairly old, too. Please check the memory vendor QVL for compatibility. Or choose a kit at or below 3600Mhz to ensure the best chance of plug and play...
  11. * Memory instability. The applied settings arent...

    *
    Memory instability. The applied settings arent passing training, so the subsequent restarts are the system attempting to do so. With XMP 1 applied, try using Maximus Tweak Mode 1. You may need to...
  12. Current Capability simply increases the amount of...

    Current Capability simply increases the amount of current allowed through the die before OCP. If you're not experiencing any OCP behavior, it can be left alone and the default setting is of no...
  13. Overclocking memory holds no assurances. SoC...

    Overclocking memory holds no assurances. SoC voltage can need to be adjusted manually. Test methodically within the region of 0.850 to 1.15v.
  14. Replies
    3
    Views
    226

    If the artefacting only occurs when an offset is...

    If the artefacting only occurs when an offset is put on the GPU core then the overclock is not stable. Turing will normally crash before producing artifacts due to the error correction, but if they...
  15. Currently can't confirm which boards will have...

    Currently can't confirm which boards will have extended support for 109XX series, however, ones that receive UEFI updates should support up to 256GB.
  16. *Hello, cache speed can have an impact on memory...

    *Hello, cache speed can have an impact on memory stability, yes. Errors can occur at point of uncore/memory interaction, and are more likely to occur when the uncore domain is being pushed further. ...
  17. I wouldn't recommend running Furmark at all....

    I wouldn't recommend running Furmark at all. NVIDIA has implemented throttling when furmark is detected in the past. With the new OC scanner functions, there's no real reason to test stability with...
  18. Replies
    17
    Views
    824

    Likely not, 4 channels will always induce...

    Likely not, 4 channels will always induce additional latency. You may want to look at the sub timings, too.
  19. Replies
    17
    Views
    824

    4 DIMMs. 82040 82041

    4 DIMMs.

    82040


    82041
  20. Hello, the test software is Google Stress App...

    Hello, the test software is Google Stress App test ran through BASH terminal (Linux subsystem) on Windows 10.
  21. Hello, both the Hero and Formula share the same...

    Hello, both the Hero and Formula share the same DRAM topology. 3600 is more than achievable with 4 DIMM kits, but it's always best to stick to ones that are present on the QVL.

    81909

    81911
  22. The memory is unstable. If Tweak Mode 2 nets...

    The memory is unstable.

    If Tweak Mode 2 nets better stability, then best to stick with it. Mode 2 can offer better compatibility depending on the memory kit and CPU.
  23. Replies
    0
    Views
    1,593

    Sticky: Official ROG Discord Server

    In order to keep up with the ever-changing social landscape, we’ve opened an official Discord server for the motherboard and GPU product categories. Discord is widely lauded as the preferred chat...
  24. Replies
    0
    Views
    2,486

    Sticky: Official ROG Discord Server

    In order to keep up with the ever-changing social landscape, we’ve opened an official Discord server for the motherboard and GPU product categories. Discord is widely lauded as the preferred chat...
  25. Replies
    0
    Views
    3,331

    Sticky: Official ROG Discord Server

    In order to keep up with the ever-changing social landscape, we’ve opened an official Discord server for the motherboard and GPU product categories. Discord is widely lauded as the preferred chat...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4