Search:

Type: Posts; User: mdzcpa

Page 4 of 20 1 2 3 4 5 6 7

Search: Search took 0.01 seconds; generated 41306 minute(s) ago.

  1. Yes, they all exhibit the behavior. All BIOS...

    Yes, they all exhibit the behavior. All BIOS versions for me on M11 Hero exhibit behavior. I leave my system connected to power source so I never really encounter the issue much.
  2. Replies
    24
    Views
    3,275

    Hold on. Are you reporting your max peak...

    Hold on.

    Are you reporting your max peak voltage recorded during transient event (starting a benchmark), or are you reporting sustained voltage under load? Wondering if you are picking up...
  3. Replies
    24
    Views
    3,275

    Then it is likely you have another setting not at...

    Then it is likely you have another setting not at Default. Yours would be the first case I've seen on any M11 board that loaded voltage exceeds what is set under Additional Turbo Voltage.
  4. Replies
    24
    Views
    3,275

    Change MCE back to Auto Set your Power Package,...

    Change MCE back to Auto
    Set your Power Package, Current Capability and Short and Long Term Durations back to Default
    Enter 1.315 as your Additional Turbo Voltage
    Leave Offset at AUTO


    With LLC...
  5. Are you getting the double boot on a simple "cold...

    Are you getting the double boot on a simple "cold boot" or are you getting the double boot after powering down the motherboard completely (shut off at the power supply)?

    I suspect you are hard...
  6. Replies
    24
    Views
    3,275

    Using adaptive voltage I don't bother with...

    Using adaptive voltage I don't bother with offset. I simply set my OC voltage to 1.315. Leave Offset at 0. LLC 6.
    I leave MCE on Auto to handle the power parameters.
    I leave speedstep and all c...
  7. Replies
    8
    Views
    965

    You can set custom pump speed curve in Fan Expert...

    You can set custom pump speed curve in Fan Expert in AI Suite 3. Depending on where you connected the pump (the mobo AIO or CPU header, there will a fan curve in Fan Expert for it.
  8. Replies
    5
    Views
    1,582

    Those monitoring specs are only for custom water...

    Those monitoring specs are only for custom water cooled setups. Those measurements are only reported when you connect a flow rate meter and thermistors to the flow rate and water temperature headers...
  9. I think the point is that your CPU is not...

    I think the point is that your CPU is not defective. Anything above 2133Mhz is an overclock and not guaranteed. Hopefully you will be honest and say you want to exchange your CPU because it won't...
  10. Replies
    35
    Views
    14,345

    So you don't want to be "bothered" by the...

    So you don't want to be "bothered" by the solution. Understood. Carry on.
  11. Replies
    10
    Views
    1,600

    Are you running without the pump housing cover...

    Are you running without the pump housing cover on? If you do, the pump will make clicking sound. Placing the cover on eliminates the clicking. It has to do with the magnets in the pump housing...
  12. Replies
    35
    Views
    14,345

    I'm a bit confused about the problem here. Am...

    I'm a bit confused about the problem here.

    Am I the only one that has no problem simply checking the Critical Temperature box and setting curve however I want it?

    A pic of CPU Fan control is...
  13. Replies
    10
    Views
    1,600

    The NA under CPU Fan would be correct now if not...

    The NA under CPU Fan would be correct now if not connected.

    For other readers of this thread:

    RYOU users will have 2 fan curves under Fan Expert (1 for the pump, and 1 for the rad fans)
    RYUJIN...
  14. Replies
    4
    Views
    276

    If that monitor has displayport (which I believe...

    If that monitor has displayport (which I believe it does) you might want to try a displayport cable.

    That mobo should technically support that card temporarily until you upgrade the rest. Make...
  15. Replies
    6
    Views
    17,623

    If you are manually setting up your fan curves in...

    If you are manually setting up your fan curves in the UEFI, make sure you a properly selecting PWM versus DC for 4 or 3 pin fans. Also, make sure to run Fan Tuning in the UEFI before setting the...
  16. Yes. That is normal behavior. Windows just...

    Yes. That is normal behavior. Windows just re-named it. I ended up changing my back to RYUJIN under Administrative Tools and it never changed again.
  17. Replies
    10
    Views
    1,600

    Hold on. You should have 3 fan curves in Fan...

    Hold on.

    You should have 3 fan curves in Fan Expert.

    1st is for the pump. That will be on the AIO header or the CPU fan, wherever you put it
    2nd is for BOTH rad fans. All radiator fans run...
  18. Replies
    4
    Views
    276

    what monitor do you have? That 2080ti will...

    what monitor do you have?

    That 2080ti will choke on that CPU. You will be stuck at PCIE 2.0. I know you're too deep budget wise, but even a 9600k on a budget 390 board would be a huge...
  19. Replies
    10
    Views
    1,600

    Double check you USB connection to the...

    Double check you USB connection to the motherboard
    Double check all connection from the cooler

    I am assuming you see the PUMP and the RAD Fans in Fan Expert (so you have 2 controllable fan...
  20. Is that memory on the QVL for the Hero XI? The...

    Is that memory on the QVL for the Hero XI?

    The Maximus XI Z390 boards run best with 4 DIMMs populated due to the topology design. You may need to custom tune those sticks. Have you tried...
  21. Word of advice. Stop looking in the Event Viewer...

    Word of advice. Stop looking in the Event Viewer to find problems. I used to do that too. I'd spend countless hours troubleshooting everything from overclock stability issues to driver conflicts....
  22. Replies
    5
    Views
    449

    Did you run Fan Tuning under Fan Expert and then...

    Did you run Fan Tuning under Fan Expert and then Enable Extreme Quiet? That lets me take my fans all the way down from stop to 20%
  23. Poll: I certainly will not "switch." My 9900k is...

    I certainly will not "switch." My 9900k is running strong at 5.1ghz and the Z390 Hero XI offers most of the latest bells and whistles. I think what will be more relevant is whether more current...
  24. The board will always boot up with the last UEFI...

    The board will always boot up with the last UEFI configuration you set. So if that is overclocked, that is what you will get.

    AIS is more for overclocking on the fly from Windows. It is not as in...
  25. Replies
    4
    Views
    3,513

    It's no the board. You problem is that the pump...

    It's no the board. You problem is that the pump is running low rpm.

    I suggest connecting the PUMP to the AIO Header. That's what its for. Then Disable CPU Fan monitoring.

    I also suggest you...
Results 76 to 100 of 498
Page 4 of 20 1 2 3 4 5 6 7