Search:

Type: Posts; User: Snakeyes

Page 3 of 12 1 2 3 4 5 6

Search: Search took 0.01 seconds; generated 60291 minute(s) ago.

  1. I would strongly suggest checking out Raja@ASUS...

    I would strongly suggest checking out Raja@ASUS suggestions. If your cooler is fairly large and heavy, you could try temporarily placing your PC on its side with the motherboard horizontal facing up....
  2. It might be worth trying, substantially loosening...

    It might be worth trying, substantially loosening your timings and frequency to see if you can get both sticks recognized. If it works, you can work up from there. Unfortunately, I doubt if it is a...
  3. Yup. To reiterate what I said earlier, with...

    Yup.

    To reiterate what I said earlier, with Intel CPUs the impact of different memory speeds is minimal and definitely not noticeable unless the PCs used for heavy video and picture editing. AMD...
  4. Taking the consideration the silicon lottery...

    Taking the consideration the silicon lottery issue the 2x16 GB CL 15 looks like a good choice. Keep in mind that unless you are planning on doing a lot of video editing/Photoshop etc. etc. the impact...
  5. Have you tried playing around with slots A1 and...

    Have you tried playing around with slots A1 and B1? I presume both sticks work individually in slot A2.



    You did check if the pins on the CPU were perfectly aligned?
  6. 1) 2x16 GB is better than 4x8 GB

    1) 2x16 GB is better than 4x8 GB
  7. Try reseating your CPU. Before that check...

    Try reseating your CPU. Before that check carefully if all the pins are properly aligned (not bent/angled). This is a frequent cause of your symptom.
  8. Replies
    3
    Views
    1,142

    Clearly looks like a hardware issue. This is a...

    Clearly looks like a hardware issue. This is a long shot, but try blowing into the rear jack with compressed air. You could also try inserting a fine long enough pin to dislodge any encumbrance. Make...
  9. Replies
    4
    Views
    1,028

    I use chrome and am having no issues on this...

    I use chrome and am having no issues on this website.


    https://www.asus.com/us/Motherboards/ROG-MAXIMUS-X-CODE/HelpDesk_Download/
  10. Replies
    12
    Views
    2,536

    You don't have to commit suicide. Just look your...

    You don't have to commit suicide. Just look your wife in her eyes and tell her she's fat. Like that very, brave but foolish, earlier poster, the Late Mr. Panzlock did.
  11. Check out the following overclocking article by...

    Check out the following overclocking article by Raja. While the article focuses on 270 a lot of it is applicable to your board. Here's a quote that might be applicable to your situation.


    "Also...
  12. Nice job! Kudos for hanging in there. Enjoy your...

    Nice job! Kudos for hanging in there. Enjoy your system
  13. If your memory speeds are being down clocked as...

    If your memory speeds are being down clocked as well, then I would increase the BLCK in bios so that CPU-z is showing 100. Make a note of that adjustment and now play with overclocking with the new...
  14. Here are a couple of suggestions. If your...

    Here are a couple of suggestions.


    If your BLCK is truly set at 96, it should reduce your memory speeds to reflect the same ratio. Does it do that? If it does, then try playing with increases in...
  15. What happens if you set your BCLK at say, 105? Or...

    What happens if you set your BCLK at say, 105? Or any number above 100
  16. Replies
    6
    Views
    8,700

    Sorry to hear that. I would follow jab383's...

    Sorry to hear that. I would follow jab383's advice and do the following. Leave the settings the same as before, but switch to manual voltage and increase voltage to 1.4 or 1.425 and retry. Just watch...
  17. Replies
    6
    Views
    8,700

    Try the following: – Down clock your memory...

    Try the following: –


    Down clock your memory to 3600.
    Make sure SVID is set to auto or enabled.
    In Vcore choose adaptive (+) and set Vcore to 1.36 v
    Set both AC load line and DC load line to...
  18. Replies
    8
    Views
    3,433

    Set it at 1.35 and if that is stable, work your...

    Set it at 1.35 and if that is stable, work your way down.
  19. Replies
    8
    Views
    3,433

    You need to enable CPU SVID support for that...

    You need to enable CPU SVID support for that option to show up
  20. Thread: Deleted

    by Snakeyes
    Replies
    597
    Views
    424,866

    I have been struggling with the same issue. The...

    I have been struggling with the same issue. The best I can come up is a light blue shade. Does not make sense to me
  21. Replies
    8
    Views
    3,433

    A couple of suggestions. Set both AC load...

    A couple of suggestions.


    Set both AC load line and DC load line to 0.01 in section "Internal CPU Power Management".


    Set adaptive to positive and enter a voltage that is about 0.05 V less...
  22. Replies
    8
    Views
    3,433

    See below

    See below
  23. Replies
    8
    Views
    3,433

    Adaptive versus manual Vcore

    More than a few posters have indicated that they are using der8auer's excellent YouTube overclocking guide for their initial overclock's. If you have reached stability using those guidelines,...
  24. Replies
    1
    Views
    659

    If you can smell burning, one of your hardware...

    If you can smell burning, one of your hardware components (possibly motherboard) is toast (:-)). I would not turn on the PC anymore and immediately disconnect it from power before you damage any...
  25. Replies
    1
    Views
    1,031

    CPU overclocking temperature control ?

    Any one know why the "CPU overclocking temperature control" feature was dropped from the Maximus X Bios ?
Results 51 to 75 of 276
Page 3 of 12 1 2 3 4 5 6