Search:

that's because the minimum processor state is set to 99% for the power plan, you can set it to lower number

it's due to the chiplet design that it has half of the memory write speed for 1 chiplet

also maybe try redownload the bios with different browser and use the back flash to do the bios update....

you probably do not have show file name extension checked.
82008

it's simple, they have to have worst case scenario in mind so that it will work for all CPU out of box.
they cant control what consumer will be getting comparing to the engineering sample they...

C7H

wifi:
C7H WIFI

2801 seems to be running well for my C7H+3700x compare to the previous 2703 BIOS
here is my result from cinebench r15
all stock except ram oc, Flare-X 3200Mhz CL14 * 4...

0002 by Shamino isn't modded BIOS, he is actually new Asus dev for the BIOS after elmor, I believe.
they do seem to be lacking communication lately /shrug

my guess is that there is not much point...

if you been using DOCP profile, maybe try use the dram calculatorby 1usmus to do manual oc w/ safe preset.
and if you been using dram calculator profile, make sure you are using the latest one to...

it's a known issue, current solutions are
1. either use the 0002 beta bios, which is the 2703 with fan fix (best solution, I think) can be downloaded here link
2. you can try uncheck the EC support...

well, BSOD can happen with the windows update easily lately.
for one, this is what I am currently experiencing, some get reboot without warning, some get bsod...

the 0002 is the 2703 + fan fix beta

that's unfortunate.
I had recently upgrade the cooling to ek's and that's how I solved the issue I had with motherboard light up (RGB n whatever lights) but wont boot.
I knew there was a short...

well, since you have the EK's block
try to trim the wing on the gasket or duct tape it.
the gasket can be conductive and can cause issue.
...

https://rog.asus.com/forum/showthread.php?92648-PCH-Temperature-up-to-70%B0C

here is old post for similar question of yours.
not really sure why yours run high, maybe your graphic card generate...

my apology, i thought you found the picture on internet.
you can also try just remove all the panel and see if temp helps for a quick test before going for all open test. removing side, top and...

can just disable the pump control completely and see if it stay @ full speed.
and you can also use the pwn header of the pump in some other fan header to see if you get proper control
if you do,...

why not just take picture directly from your build?
maybe you simply have the fan installed in a bad orientation ? i.e hot air trapped in the case.
or maybe it is poorly applied thermal pad on the...

mainly do it when there is AGESA change.
otherwise, just do wit when you experience weird issue, BSOD, or instability.

I think 0002 is the 7403 w/ fan fix.

glad you have it sorted out and it is working again :)
alway remember heat up the CPU before removing it.
Pulling the CPU along w/ heatsink can potentially damage the pins, like pulling the pin...

change the profile version to V1/V2 might provide you different timing and voltage
Also try safe preset first.

And I thought 3600Mhz is the sweet spot, maybe consider that too?

IMHO, you should have kept everything in the same thread instead of making a new one every single update w/o proper explanation in text.
and 3 URL isn't going to make them understand what you want,...

when I swap from 2700x to 3700x, I did notice it reinstall tons of stuff right away; though I have yet to experience any BSOD.
I initially ran DOCP profile, then do the memory oc. have no problem...

it sounds more a hardware issue than a BIOS issue, unless there were other working version of BIOS.
it will be reason enough if you have gone thru all troubleshooting steps.
just be sure to add the...

it's not faulty, it's how it works due to how memory path being mapped out.

A2 B2 provides the best signal strength for memory when you use 2 dimms

it is also clear stated in the instruction as...

might be wrong, but that sounds like you are using DOCP setting. change docp setting to manual should allow you to set the bclk to 100
loading DOCP profile = bclk @ 99.8.