Search:

on 3 May 2021 I have Requested a An RMA for the Broken Fan Controller that Came with my Maximus XIII Extreme
The problem was that the RGB showed the Wrong colors when connected to controller and...

Did you install the plugin for Aura support from the Corsair website ???
If you need to reinstall I recommend to install that Plugin before installing any of Asus there Aura Software
Also use the...

So here is a Little update

I noticed that there was an update for "Device & Component" that was marked as "Memory"
And I looked into Aura Creator to see if it would appear there ... and it did...

Yeah ... A bit more information on your situation might be useful

If I recall correctly the WD_BLACK AN1500 is an PCIe Card
However it's unclear in what slot it is installed (some PCIe Cards...

Yeah that is true but USB 2.0 interfaces have become a lot better and firewire interfaces are really hard to find these days (Not to forget that you need a TI based firewire card since those work...

From digging a bit into the Manual I found that the Bottom X16 Slot will actually disable some Sata ports (Sata6G_12 & Sata6G_34)
There is no way around that that
if the 2080ti you have is a 3...

The SATA6G connections are mainly used for connecting extra SSD / HDD / ODD
the board has a total of 6 but if you want to use the thunderbolt Card you might have to disable the last 2 of these (5 &...

it depends on the power draw of the devices ... if the total does not exceed the 3A your fine
if it does you might want to confider A Powered ARGB Hub or an extension cable that Provides power...

If I may ask ... is there any participle device you need thunderbolt for ?

Looking from what you are saying the board you have is a "ROG STRIX Z590-E GAMING WIFI" if I am correct
That board...

just posted this for somebody else

88805

You can actually set the GEN per PCIe Slot
So you might want to try setting "PCIEX16_2" to Gen 3 to see if this solves the problem
if it does than we...

Silly Question but .. What slot is your NVMe drive installed in ???
If it is installed in M.2_1 or M.2_2 you might want to change some settings in your bios

1st one is important for using M.2_1 &...

if the board has a Thunderbolt header it is possible but then you need to use the included Display port cables to go from your GPU to the Thunderbolt card

uhm ... If it's a Thunderbolt port it will probably work but this is also dependent on the CPU

it also depends on what you mean by "improve the graphics" ...
Better image Quality, Maybe ... ...

You might want to test if running your RTX3090 in x8 makes a difference to running it in x16
if it does not make a difference than than you might be better of using it that way and putting your WD...

unfortunately you did not say that you tried the Dimm.2 first
you actually started about the slots on the board
You did not say that you tried A Cmos reset or updated the bios (Only that you...

RTFM

Regarding the CPU Lanes:

Intel® 10th Core Processors:
- M.2_2 supports PCIE 3.0 x4 mode M Key design and type 2242 / 2260 / 2280 PCIe storage devices
- M.2_2 slot shares bandwidth with...

if it does automatically detect that there is a card in the second x16 slot the first slot will run at x8
this is pretty normal behavior since it shares the 16 GPU allocated lanes
The only thing I...

Have you tried Reinstalling the drivers for the card ???
ithe x4 Slot is connected to the chip-set while the x16 goes to the CPU
also in the bios set the lanes x8 + x8 or x8 + x4 + x4
in the last...

Have you installed the Aura Plugin that is on the Corsair website ?
and also this might be useful...

He needs to drain his loop to change this ... it's a lot of work
if he wants to access the M.2_1 or M.2_2 slots he will need to remove his GPU ... since the GPU has an EK block means draining the...

If I recall correctly there are some settings for this in the Bios
You have the options to set x16 / x8 + x8 / x8 + x4 + x4
The last one also has 2 options that allow the 2nd Full size PCIe on x4...

the 3 slots on the board are all Gen 4
If you want to run your GPU at x16 you need to use the top slot (M.2 3 I believe)
in your case this will be the one that is also cooled by the monoblock

You can actually make it work properly with Aura Creator if you like (Since your board only has one ARGB Header)
The only thing you will need to do is set the Swap the Color amount numbers between...

Should be possible ... however I have not seen any way to change the PUMP Headers to be % controlled only seems to be temperature controlled from within fan xpert

Also note that 2 Noctua Fans will...

There is no calibration option for ARGB strips only for RGB as those have individual wires per Color

Please note that the links you provide are both not listed as "Aura Compatible"
However the...