Search:

Type: Posts; User: NemesisChild

Page 2 of 20 1 2 3 4 5

Search: Search took 0.02 seconds; generated 41943 minute(s) ago.

  1. You may have a short somewhere but I'm leaning...

    You may have a short somewhere but I'm leaning towards a GPU failure since you are getting graphical corruption.

    Here's what I would do, disconnect everything including all drives and USB devices...
  2. Have you looked at any software like HWMonitor to...

    Have you looked at any software like HWMonitor to see what is reports for DRAM voltage?

    We have seen this happen on a few boards where no matter what DRAM voltage is set in the bios, the actual...
  3. Your DRAM voltage looks low at 1.20v. Isn't that...

    Your DRAM voltage looks low at 1.20v. Isn't that a 1.35v set?
  4. Load all bios settings at default (including your...

    Load all bios settings at default (including your memory) and test stability.
  5. Thread: Run sli

    by NemesisChild
    Replies
    2
    Views
    251

    Yes, they are the same GPU. Keep in mind that in...

    Yes, they are the same GPU. Keep in mind that in SLI, both cards will run at the slowest speed of the two at default clocks.

    You can always overclock the non OC card to match the OC edition, but...
  6. Do you mean it happens after being unplugged from...

    Do you mean it happens after being unplugged from the wall?

    This is normal behavior whenever power is disconnected from the motherboard.
  7. Replies
    18
    Views
    1,242

    I can overclock my 3600 CL16 kit to 4000 just by...

    I can overclock my 3600 CL16 kit to 4000 just by raising the DRAM voltage. No other timing adjustments needed.

    And btw, it's a RGB set.
  8. Most PSU manufactures split the 8-pin CPU cable...

    Most PSU manufactures split the 8-pin CPU cable into a 4+4 pin connection because some non-enthusiast boards only have a 4-pin CPU port.

    As Menthol said, just use the 4+4 pin connector and you'll...
  9. Replies
    202
    Views
    47,484

    13.55v and you haven't fried your system? lol

    13.55v and you haven't fried your system? lol
  10. Replies
    1
    Views
    318

    Welcome to the forum! This is completely...

    Welcome to the forum!

    This is completely normal behavior after cutting off power to the mobo. It has to do mostly with memory training and not the bios version.

    If I recall, there should be an...
  11. Replies
    2
    Views
    1,016

    Are you getting a failed overclock message on the...

    Are you getting a failed overclock message on the American Megatrends screen?
  12. Welcome to the forum! Do you have to do a hard...

    Welcome to the forum!

    Do you have to do a hard restart when the freezing occurs? Have you tried running with all bios setting at default?

    Also, failing or defective USB devices can cause...
  13. Anytime power is cut off from the board, the bios...

    Anytime power is cut off from the board, the bios goes through a series of memory training cycles/reboots.

    This is completely normal behavior.
  14. Replies
    6
    Views
    372

    Yes I'm having a close encounter with my mashed...

    Yes I'm having a close encounter with my mashed potatoes.
  15. Replies
    4
    Views
    1,191

    Why would bios 1704 be a last resort?

    Why would bios 1704 be a last resort?
  16. I've tested 3200 & 3600 kits, the 3600 kits hands...

    I've tested 3200 & 3600 kits, the 3600 kits hands down can overclock a whole better.

    I can easily hit 4000 (same CL16 timings) with my 3600 G.Skill set simply by bumping the DRAM voltage to...
  17. Replies
    18
    Views
    1,281

    Delidding is the way to go: ...

    Delidding is the way to go:

    https://siliconlottery.com/collections/all/products/delid?variant=12391254949974
  18. Are you kidding? Newegg is probably the most...

    Are you kidding? Newegg is probably the most trusted and reliable source for PC parts on the web.

    I've been buying from Newegg for many years, never once had a problem.

    They stand by their...
  19. Replies
    14
    Views
    2,446

    Try posting with all SATA and M.2 drives...

    Try posting with all SATA and M.2 drives disconnected.
  20. Did you try different USB ports? I've had...

    Did you try different USB ports?

    I've had similar experiences when a USB device is failing. How old is the 4000?
  21. Set your Dram voltage to 1.35v and see what it...

    Set your Dram voltage to 1.35v and see what it shows in the bios after a reboot.

    Is your memory a single matched set? 2x16GB or 4x8GB set?

    Also please note the make, model, and age of your PSU.
  22. Welcome to the forum! Is anything else...

    Welcome to the forum!

    Is anything else overclocked besides the memory?
    Have you tried testing at default bios settings over a long period of time?
    Have you tried clearing the CMOS?
    Have you...
  23. I misread your post earlier, I get it... LOL

    I misread your post earlier, I get it...

    LOL
  24. Chair? lol

    Chair? lol
  25. Have you tried clearing the CMOS?

    Have you tried clearing the CMOS?
Results 26 to 50 of 498
Page 2 of 20 1 2 3 4 5