Search:

Type: Posts; User: Silent Scone@ROG

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds; generated 108134 minute(s) ago.

  1. Sounds like the system isn't stable enough to...

    Sounds like the system isn't stable enough to pass a cold boot every time. Try increasing VSOC voltage. 3600 should scale to around 1.08v automatically depending on board and UEFI revision. You can...
  2. 1.67v? What LLC are you setting? I don't have...

    1.67v? What LLC are you setting? I don't have this platform to hand.

    Adaptive requires that the voltage input is above the minimum VID for a given ratio. In order to do this you would need to...
  3. This. With passive cooling anything under 70c is...

    This. With passive cooling anything under 70c is acceptable. With heavy data writes these drives can get fairly warm.
  4. What you're currently using. The CPU will boost...

    What you're currently using. The CPU will boost on it's own within the predefined power envelope
  5. Hello, No, you haven't missed anything. If...

    Hello,

    No, you haven't missed anything. If disabling PBO the CPU is constrained within stock TDP
  6. Replies
    5
    Views
    368

    Hello, If not done so remove the CPU and...

    Hello,


    If not done so remove the CPU and check the socket for bent pins, remount the CPU with even mounting pressure.

    Clear the CMOS as per instructions depicted in the user manual via the...
  7. Hello, CPU-Z displays the CPU VID and not the...

    Hello, CPU-Z displays the CPU VID and not the supplied voltage (Vcore)
  8. Hello, Did you enable DOCP prior to the issue...

    Hello,

    Did you enable DOCP prior to the issue occurring?


    1. Turn off the computer and unplug the power cord

    2. Locate CLRTC pins as per snip below

    3. Short circuit the pins with a...
  9. Replies
    5
    Views
    663

    Hello, You've not posted in the correct...

    Hello,

    You've not posted in the correct section at all which hasn't helped you in getting any replies.

    error 41 is fairly generic and is synonymous with a lot of system crashes.

    Does the...
  10. Hi, You've not mentioned which software you're...

    Hi,

    You've not mentioned which software you're referring to? If it's third party such as HWInfo, you're best off asking the author.
  11. The iCUE uninstallation could be a red herring,...

    The iCUE uninstallation could be a red herring, hard to say. Reset the UEFI and go from there.
  12. Replies
    5
    Views
    477

    Hello, Really depends on your budget and the...

    Hello,

    Really depends on your budget and the capacity needed.

    GSKILL Neo kits are still one the best options due to GSKILL's vigorous hand binning. Look for anything in the 3400-3666 range....
  13. Hello, What did you adjust in the BIOS...

    Hello,


    What did you adjust in the BIOS prior the problem starting? Have you tried to reset the UEFI via the rear I/O panel?
  14. Hello, Devcon is the driver handoff console,...

    Hello,

    Devcon is the driver handoff console, and that message can sometimes be related to the driver being incompatible with the OS version.

    Try from here:...
  15. Hello, Despite it happening in both operating...

    Hello,

    Despite it happening in both operating systems I would be tempted to install a fresh dummy OS on a separate drive and see if the problem persists there. A failing PSU will often result in...
  16. Replies
    11
    Views
    1,098

    No worries, will pm.

    No worries, will pm.
  17. Yes, the vcore is normal. Flash to the latest...

    Yes, the vcore is normal. Flash to the latest UEFI if looking for the latest AGESA from AMD
  18. Hi, please respond to the other thread as have...

    Hi, please respond to the other thread as have asked for Q-Code received.
  19. Replies
    20
    Views
    1,726

    Was replying to the post above. 5K is tough. Hard...

    Was replying to the post above. 5K is tough. Hard to say when not comparing sub timings. Q-Code should should help determine where to to start looking.
  20. Hello, This is normal behaviour for Ryzen...

    Hello,

    This is normal behaviour for Ryzen Precision Boost upward of up to 1.5v The CPU needs this much voltage in some instances to maintain frequency and adapts to high current loads accordingly.
  21. Replies
    20
    Views
    1,726

    What Q-Code? The common denominator is likely...

    What Q-Code?
    The common denominator is likely using a previous generation CPU on a next gen board. Optimisations and auto rulings when pushing limits to the very edge as you are doing are often with...
  22. Remove AI Suite then reset the UEFI to optimised...

    Remove AI Suite then reset the UEFI to optimised defaults.
  23. Hi, if you don't use AI Suite for anything other...

    Hi, if you don't use AI Suite for anything other than 5 way, I would recommend removing and let the board control boost behaviour on its own.
  24. Replies
    20
    Views
    1,726

    You can enable Fast boot to avoid retraining the...

    You can enable Fast boot to avoid retraining the memory, this should decrease POST time.

    Be sure to try both XMP profiles 1 and 2. Often, XMP II timings will be slightly looser depending on the...
  25. Replies
    11
    Views
    1,098

    Thanks for that. Can you give me your...

    Thanks for that.

    Can you give me your specification and upload a DXDIAG, please? (Type Dxdiag into Windows Search, open DXDIAG and click save information)

    Have you changed anything since the...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4