Search:

Type: Posts; User: Enderwiggin03

Page 3 of 8 1 2 3 4 5 6

Search: Search took 0.01 seconds; generated 66445 minute(s) ago.

  1. Replies
    4
    Views
    5,108

    Could use a splitter? Also have the M.2 fan (but...

    Could use a splitter? Also have the M.2 fan (but I think it's setup differently).
  2. Replies
    8
    Views
    1,691

    No need to use the jumper, you just have to one...

    No need to use the jumper, you just have to one time make the connection to turn on the PC, leaving that jumper on might cause it to turn off (like holding the power button)
  3. Replies
    8
    Views
    1,691

    His ram's at 2666mhz, I doubt it's a training...

    His ram's at 2666mhz, I doubt it's a training issue.
  4. Replies
    8
    Views
    1,691

    Have you tried a different power supply? Also,...

    Have you tried a different power supply? Also, you can use a screwdriver to power on the motherboard if you put it between the two power pins (PWRSW PWRBTN# and the GND as shown on page 1-20 in the...
  5. Strange, I used the ones I got off here for my...

    Strange, I used the ones I got off here for my wife's Z490-E and no issues with 12C device etc.
  6. Well, have you tried getting the Intel Chipset...

    Well, have you tried getting the Intel Chipset drivers from the forum here? Might want to check all of those out. Check this thread...
  7. Replies
    674
    Views
    119,654

    I only saw 0703?

    I only saw 0703?
  8. Replies
    4
    Views
    1,017

    Was this with XMP? You might have to try manual...

    Was this with XMP? You might have to try manual timings.
  9. There's a username I haven't seen in a while.

    There's a username I haven't seen in a while.
  10. Should be fine with 1.0.1.4 after the firmware...

    Should be fine with 1.0.1.4 after the firmware update.
  11. You might have to install the older driver...

    You might have to install the older driver version 1.0.1.3 I think to get the firmware update to work (at least I did for my wife's Z490-E).
  12. Replies
    14
    Views
    2,021

    Nah, I've tried different ram, and my previous...

    Nah, I've tried different ram, and my previous 9900k couldn't do it either.
  13. Replies
    14
    Views
    2,021

    Well, in my case it won't even post with XMP...

    Well, in my case it won't even post with XMP turned on...
  14. Replies
    14
    Views
    2,021

    Tried this, the board wasn't having it, sadly....

    Tried this, the board wasn't having it, sadly. Back to 4000mhz.
  15. Replies
    14
    Views
    2,021

    Good luck, I have the same board and I couldn't...

    Good luck, I have the same board and I couldn't get any higher than 4000mhz with my setup. I honestly think getting the higher frequencies require the exact kits in the QVL.
  16. Replies
    674
    Views
    119,654

    Are these Beta? I'm not seeing them on the...

    Are these Beta? I'm not seeing them on the Support site, which is why I was asking.
  17. I was under the impression Z490 had more PCI-E...

    I was under the impression Z490 had more PCI-E lanes.
  18. That cooler is for the NVME drives from what I...

    That cooler is for the NVME drives from what I can tell, unless you have some ridiculous cooler on your 2070 Super, I dunno why you're having issues.
  19. Are you using the video card in the correct slot...

    Are you using the video card in the correct slot (1)? Is your NVME drive in one of those slots next to the RAM? If so, that'll reduce your PCI-E Lanes going to the CPU. The sound card is using the...
  20. Can't use Crate and Aura at the same time.

    Can't use Crate and Aura at the same time.
  21. Unplug the power supply from the back of the PC,...

    Unplug the power supply from the back of the PC, hit the power button for about 10 seconds or so, plug it back in, and retry it. If that doesn't work, try CMOS reset.
  22. Replies
    6
    Views
    682

    What specifically were you looking for?

    What specifically were you looking for?
  23. Replies
    6
    Views
    682

    Mine has been well, it's either the IMC com my...

    Mine has been well, it's either the IMC com my 9900k, or the board that won't allow me better than 4000mhz from my 4266mhz RAM kit. All 4 slots used though (4x8GB).
  24. Replies
    51
    Views
    10,406

    Everything works fine here on Z390-E with 1401.

    Everything works fine here on Z390-E with 1401.
  25. I thought it was a Windows 10 1903 problem?

    I thought it was a Windows 10 1903 problem?
Results 51 to 75 of 192
Page 3 of 8 1 2 3 4 5 6