Search:

Type: Posts; User: xeromist

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    1
    Views
    34

    My understanding is that 8gb of memory is...

    My understanding is that 8gb of memory is permanently soldered. That means you are limited to changing one stick and anything over an 8gb stick will operate in single channel mode at lower...
  2. No, all that button should do is cause a...

    No, all that button should do is cause a discharge so settings are forgotten. Doing it multiple times won't behave any differently.
  3. The components will be a little cooler with less...

    The components will be a little cooler with less power flowing through them but because the fans are slower or off a little bit more heat will build up inside the chassis. Nothing to worry about.
  4. Keep in mind that overall performance is going to...

    Keep in mind that overall performance is going to be lower in silent mode. For some games that may not matter but in demanding titles you might find it's not good enough. If it works for your games...
  5. Replies
    3
    Views
    225

    Servers use them for redundancy in case one fails...

    Servers use them for redundancy in case one fails so think of it like a single 1200w PSU that's just really reliable. Unfortunately because of the small dimensions they use little tiny fans which are...
  6. Replies
    4
    Views
    228

    That issue was with the Live Update software, not...

    That issue was with the Live Update software, not software updates posted to the website. I guess if you don't trust ASUS you can trust that researchers and hackers were going over ASUS software with...
  7. Replies
    8
    Views
    171

    If you do not plan to overclock then 850w should...

    If you do not plan to overclock then 850w should be sufficient for your needs for now. That should be enough power even with a GTX3090 as long as the PSU has enough connectors for whatever card you...
  8. *****Consolidated duplicate threads. Please use...

    *****Consolidated duplicate threads. Please use existing threads where possible. Thanks.****
  9. Thread: What happined

    by xeromist
    Replies
    3
    Views
    195

    Is it still working now a few weeks later?...

    Is it still working now a few weeks later? Overcurrent protection would cut all power so you wouldn't get any post code until the trip is reset and then everything works again. The only way I could...
  10. Thread: What happined

    by xeromist
    Replies
    3
    Views
    195

    If the motherboard swap didn't fix it then I'd...

    If the motherboard swap didn't fix it then I'd say it's unlikely. Since you have two GPUs I'd try them one at a time to eliminate a GPU as a potential issue. You could also try a single memory stick...
  11. Replies
    2
    Views
    110

    Is the pad stuck to the drive or the board? A...

    Is the pad stuck to the drive or the board? A picture might help. Anyway, an adhesive pad should not be like a permanent glue. Removing it may cause it to be less sticky but it should not damage...
  12. Hey Nermalion, the inquries section is only...

    Hey Nermalion, the inquries section is only available to escalate an existing RMA. You would have to work with regular phone or email support first. AFAIK the dongle is not available separately but...
  13. ***Moved back per James's request. *** ...

    ***Moved back per James's request. ***

    Unfortunately I don't have any ideas for you, James.
  14. Where did the MP510 come from? Is it possible...

    Where did the MP510 come from? Is it possible there was an OS installed on it previously? If so you might be getting the repair message because it is trying to boot off of the MP510. I would go into...
  15. Replies
    2
    Views
    244

    You probably already figured this out but the...

    You probably already figured this out but the Crosshair is going to be better for overclocking with better power delivery. If you just want to run a CPU at stock settings even the TUF would be fine...
  16. I never said it wasn't owned by ASUS. ASUS set...

    I never said it wasn't owned by ASUS. ASUS set this up years ago for customers to discuss products with each other and has never offered it as an official support channel. There are other channels...
  17. Replies
    5
    Views
    521

    Just to clarify, it's referring to a potential...

    Just to clarify, it's referring to a potential problem upon switching modes rather than a permanent flaw in the AHCI implementation. If you install Windows after the switch you will not have any...
  18. Replies
    5
    Views
    521

    *** Moved from SI section. Must have existing RMA...

    *** Moved from SI section. Must have existing RMA ***

    Are you saying that when you change the setting it doesn't apply?
  19. Just remember that removing anything from the...

    Just remember that removing anything from the board will void your warranty and if you aren't careful you could cause collateral damage. Better to cover unwanted lights with something non-conductive.
  20. I understand your frustration. Nobody seems to...

    I understand your frustration. Nobody seems to have enough cards and it appears it will be that way for a while. FYI, this is a community forum so ASUS doesn't make any official statements here like...
  21. Replies
    2
    Views
    17,113

    I don't think a lot of boards have a bunch of...

    I don't think a lot of boards have a bunch of empty space. Some of the physical space is taken up by m.2 drives regardless of how many data lanes they use. I think to have more slots you would need...
  22. I'll admit, I'm a little jealous of the tools you...

    I'll admit, I'm a little jealous of the tools you have.
  23. You could post in the Service Inquiries section...

    You could post in the Service Inquiries section of the forum to get a second opinion. If you provide your RMA sometimes they can escalate it for you.
  24. Replies
    6
    Views
    410

    Monitors will always go into standby mode....

    Monitors will always go into standby mode. Perhaps the only option you have is a smart power strip. These have a master outlet and several slave outlets. When the master device is off the strip cuts...
  25. Replies
    2
    Views
    165

    I've had boards with the q-connector as well. I...

    I've had boards with the q-connector as well. I thought it was still around as of a few years ago. I suspect it isn't included with every board because the header pinout varies from motherboard to...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4