Search:

Type: Posts; User: syldon

Page 1 of 9 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    246
    Views
    74,945

    much appreciated

    much appreciated
  2. It looks a bit like you have a dodgy slot. This...

    It looks a bit like you have a dodgy slot. This could also be down to a poor bios revision.

    Use a clean flashing method.
    That means remove all components from the board. Only connect power...
  3. I am sorry you are quoting me but not really...

    I am sorry you are quoting me but not really answering the advice.
  4. Replies
    3
    Views
    1,197

    Try 1smus's dram calculator....

    Try 1smus's dram calculator. https://www.guru3d.com/news-story/download-dram-calculator-for-ryzen-updated-to-v1-4.html
  5. Have you tried increasing the voltages for the...

    Have you tried increasing the voltages for the Dimms? Mine boots with a lower voltage at 1.32v. It is enough to create errors. I have to boot at 1.37v-1.38v. This gives a meter reading of 1.35v. The...
  6. Replies
    5
    Views
    2,904

    0d is very early within the bios start up checks....

    0d is very early within the bios start up checks. It is having issues talking to the CPU instruction set. Remove all devices from the mobo. Leave only the power cables connected, no CPU, memory or...
  7. Replies
    3
    Views
    1,225

    Google the flashback method for the CH6. You can...

    Google the flashback method for the CH6. You can revise to any bios version. The recommendation is that you flash it twice, with a full rest to default before each one. The best way to reset the bios...
  8. Replies
    4
    Views
    959

    Most who have Sammy B die, which is the most...

    Most who have Sammy B die, which is the most compatible with Zen, are restricted to 3466mhz. There are some with posts stating 3533. Some have said that they can run 3600, but it is far from stable....
  9. Running on stock settings can be very unstable....

    Running on stock settings can be very unstable. So if your memory isn't running very well, then other stuff will be skewed. You can use the stilt's timing on a lower frequency to test it. You may...
  10. The stock settings is not as finely tuned for...

    The stock settings is not as finely tuned for performance as the stilt's. Since memory speed has a large impact on Ryzen performance, having a better memory profile is going to help puch up scores.
  11. One of the M2 slots (2.2)has a heat shield on the...

    One of the M2 slots (2.2)has a heat shield on the CH7. Using this slot reduces the PCI bus down to x8 from x16 though. The common sense thing is to use the other slot (2.1) and this one receives very...
  12. Replies
    15
    Views
    3,973

    The latest version of HWinfo and SIV have been...

    The latest version of HWinfo and SIV have been updated to not read WMI sensor from CPU 15. HWinfo and SIV are safe to use from this issue.
  13. Replies
    15
    Views
    3,973

    There is a multitude of reason why your system...

    There is a multitude of reason why your system could be bombing out. You need to supply more information.

    1. Thermal lock out? Does your system get hot. The mobo has a thermal cutout @ 115c on...
  14. Replies
    2
    Views
    420

    What vcore voltages do you have. I had bother...

    What vcore voltages do you have. I had bother with a kindle that would not get recognised. IT was down to the vcore being set too low.
  15. Replies
    7
    Views
    2,071

    There used to be a problem where memory works ok,...

    There used to be a problem where memory works ok, but crashes when gaming. Change your vddp voltage to 0.9v. If this doesnt help try 0.885v or 0.915v, mine ran best at 0.885v.
  16. CBS settings are the boards default settings for...

    CBS settings are the boards default settings for when it cant train from memory settings. Applying some settings in there will cause the system to apply them even when it fails memory training. You...
  17. Replies
    9
    Views
    1,115

    Q-Codes, 9C, A0, and b4 point to things that rely...

    Q-Codes, 9C, A0, and b4 point to things that rely on the SOC. This could be voltages or bad memory setup. No one can really point you in any direction though without specs and a bios dump.

    You can...
  18. Replies
    3
    Views
    4,309

    The first 16 qcodes are processes listed before...

    The first 16 qcodes are processes listed before it touches your memory modules. Qcodes are listed mostly in order of use in your manual page A-1. So you can check your system in bits. Remove the...
  19. You should be able to set it as a boot priority...

    You should be able to set it as a boot priority in the bios listed on page 3-21 in the manual.

    Having your M2 drive running in slot 2.2 will reduce the PCI lane allocation to your gfx card by...
  20. Thread: PC wont boot up

    by syldon
    Replies
    11
    Views
    1,678

    That would be two bets I would have lost today....

    That would be two bets I would have lost today. Your CPU and England out of the WC.
  21. Which bios file are you using?

    Which bios file are you using?
  22. When you push the flashback button it will flash...

    When you push the flashback button it will flash with a blue light 3 times. During that time it will check the flashback USB port for the correct bios file. For a crosshair 6 the filed should be...
  23. It is the usb port with the white box...

    It is the usb port with the white box highlighting it.


    74654
  24. Thread: PC wont boot up

    by syldon
    Replies
    11
    Views
    1,678

    I had similar issues with a CH6 when they were...

    I had similar issues with a CH6 when they were first released. That is the advice I received from their tech support. This advice has been repeated on a few forums now also.

    I would contact Asus...
  25. Thread: PC wont boot up

    by syldon
    Replies
    11
    Views
    1,678

    Your original post gave me the impression it was...

    Your original post gave me the impression it was an erratic problem. Because you said "a week later". I assumed that you had it working for a little while.

    Qcode 58 is CPU initialisation failure....
Results 1 to 25 of 205
Page 1 of 9 1 2 3 4