Search:

Thank you very much.
So a common 6-pin PCIe cable then.
Thanks.
*

Hello all,

One qustion...which cable should I use to connect the EATX12V_3 6-pin connector ?
Will an 8-pin EPS plug fit, leaving out the last two pins ?
It look like there is only 8-pin or 4-pin...

On the QVL list for this card, both the Sabrent Rocket 4 and Rocket 4 plus are not listed...
I know people use without any problem the Rocket 4...any reason why the Rocket 4 plus shouldn't work ?
...

Sorry !
you're right.
These from Corsair should be good:
87218

Yes,
bought this kit but not yet received...

F4-3600C16Q2-64GTZKK
https://www.gskill.com/specification/165/168/1536299994/F4-3600C16Q2-64GTZKK-Specification

Thank you very much Arne !

Hi Arne, thank you for the help.



What you mean ?

Supposing I will put the GPU in the PCIEX16_3 slot (should work at 16x), this Hyper card in the PCIEX16_1 (also 16x) and this card...

Hello,

Could be possible to use this card to add 4 more M.2 drives in this MB, but using them as 4 separate drives and not in RAID ?
Thanks

Hi,
might try this adapter:
https://www.amazon.com/JXSZ-19-pin-USB3-0-Extension-8-inch/dp/B0843SJFP9

Hello,
I would like a suggestion for which kit to buy:
MB: Zenith II Extreme Alpha
CPU: TR 3960X

Need 64GB and I was looking at these kits:...

Hi Arne,
have you tested the Optimus ?
what can you say about it ?

Just bought Zenith II Extreme Alpha and 3960X, what's the best cooling solution (more efficient) that you can suggest ?
Thanks...

G.Skill state that this kit should work https://www.gskill.com/qvl/165/184/1580374347/F4-3600C14Q2-64GVKB-Qvl

Hello,
I would like to ask for help in regard to what options I should set for the USB settings in the UEFI BIOS.
I have BIOS 3101 and I just updated the USB 3.0 drivers for both Intel and ASMedia....

I have a couple of questions regarding some settings in BIOS...

ASM106SE Storage controller :
this device, control ONLY the SATAEXPRESS_E1 port or even the two SATA6G ports E3 and E4 ?
Let say I...

Hi, I think *not an expert* what you see is correct.
-ASMedia stuff is MB USB 3.0 ports you have on the back
-Intel USB 3.0 are the two (red) connectors on the MB
-The Generic SuperSpeed USB Hub...

Updated to BIOS 3009, set XMP profile and everything is fine..32GB at 3000MHz !!
After windows started I saw two new devices added successfully...something Xeon related...checked devices management...

Hi Nate152,
Thanks for the suggestion.
By VCCIO do you mean the VCCIO CPU and VCCIO PCH voltage ?
Should I raise both to 1.25v ?
Right now they show 1.040v

Updated to 1902...set XMP profile and it see only 24 GB instead of 32...
CPU i75390K with XMP profile run at 3.75 GHz...

Thanks for the suggestion.
The bios installed when I received the mainboard was 1701.
Do it make any difference if the BIOS 1902 is listed for the NON 3.1 version of this mainboard ?
I have the...

Ok, I tried to put all the values manually but without success....I am only able to make them run at 2400MHz
I ordered one kit of F4-3000C15Q-32GRK...hope to have better luck, apparently these kits...

Thank you SO much Arne.....you are very helpful !
I want to write down the XMP value myself too, which value you type ? Only the latency or all the values of the long list ?

The latency of my ram...

In the BIOS DRAM Timing Control I see that the timings are only in for the CHA CHB and CHD channels. The CHC channel has 0 on all the options.
That mean CHC is not "recognized" or seen ? ( that's...

Updated to BIOS 1801 and set XMP to RAM, but now it see only 24GB instead of the 32.
The BOOT_DEVICE_LED is on and I have Qcode CE

Any suggestion ?

P.S: is that normal that when I set the XMP...

No, I will not send back the PSU, it work and the cable may very well be one of the old PSU that I removed....
Thanks for the info on Triangle.

Found the problem !
Was caused by a defected SATA power connector cable....
Lost three days on it....
Now going forward with the installation....

P.S : A quick question...on the three thermal...