Search:

Type: Posts; User: Silent Scone@ROG

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. If the issue only occurs when pushing memory and...

    If the issue only occurs when pushing memory and FCLK then the overclock is not stable. Tune VSOC value manually ranging from 1v to 1.15v.
  2. Hello, A number of items can have an impact on...

    Hello,
    A number of items can have an impact on the single threaded performance depending on the workload.

    BIOS and AGESA revision
    Memory latency
    Silicon quality
    Fabric Clock
    BIOS CPU...
  3. Hello, If the issue occurs when enabling the...

    Hello,

    If the issue occurs when enabling the XMP profile then the overclock is likely not stable.

    Enable XMP in the UEFI and try setting the below values to see if this helps the system pass...
  4. Replies
    7
    Views
    275

    Assigning the slots in the UEFI to GEN 3.0 that...

    Assigning the slots in the UEFI to GEN 3.0 that are populated is sufficient enough, yes.
  5. Hello, Have you tried creating a new profile...

    Hello,

    Have you tried creating a new profile on build 2006? If you're using a saved profile from an old UEFI build it's possible it's incompatible due to changes in AGESA or other rulings....
  6. Hello, Use NVFlash to revert back to V2 BIOS....

    Hello,

    Use NVFlash to revert back to V2 BIOS. You can download the correct BIOS from TPU if you did not save it. https://www.techpowerup.com/vgabios/

    Open an elevated command prompt as admin
    ...
  7. Hello, Memory stability should be tested with...

    Hello,

    Memory stability should be tested with HCI MemTest or Karhu RAM Test. OCCT Memory test is also fairly good.


    Go into the AMD Overclocking Menu in the UEFI, select Curve Optimiser and...
  8. Replies
    1
    Views
    70

    Hello, Close afterburner or any other...

    Hello,
    Close afterburner or any other application with an active OSD and try again.
  9. Replies
    524
    Views
    141,160

    See guide here...

    See guide here
  10. Replies
    10
    Views
    245

    The QVL and validation process is designed to...

    The QVL and validation process is designed to ensure the user the best possible chance of compatibility, or more importantly stability. It doesn't ensure or guarantee the kit will operate at the...
  11. Sticky: thread stickied

    thread stickied
  12. Are you using the IGPU? If not, it can be...

    Are you using the IGPU? If not, it can be disabled. Having it enabled whilst dormant will likely not have an adverse impact on performance, though.
  13. Replies
    2
    Views
    100

    Hello, This might be down to memory rules,...

    Hello,

    This might be down to memory rules, cache, or Sandra may need an update (to name a few reasons). I wouldn’t get too hung up on synthetic benchmarks, but you can try AIDA64s bandwidth test...
  14. Hello,* Please state which board. Bandwidth...

    Hello,*
    Please state which board. Bandwidth sharing information should all be available in the product manual.
  15. Have you tried changing out the Display Port...

    Have you tried changing out the Display Port cable for both screens, or alternatively only running one panel to see if this helps?

    I'm aware you tried with a different memory kit, but make sure...
  16. The reported voltage will differ depending on the...

    The reported voltage will differ depending on the monitoring tool and whether VID is being reported or vcore. The VID is the voltage the CPU thinks it's receiving, Vcore is the real-time measurement....
  17. Hello, After updating, are you using an OC...

    Hello,

    After updating, are you using an OC profile that was saved in the UEFI from the previous build? If so, wipe the profile and start over.

    How are you testing memory stability?
  18. Replies
    21
    Views
    471

    Hello, Your 10th Generation CPU has a maximum...

    Hello,

    Your 10th Generation CPU has a maximum number of 16x PCIE lanes
  19. Replies
    21
    Views
    471

    Have you tried removing all expansion cards and...

    Have you tried removing all expansion cards and NVME drives from the system and checking then?

    Might want to try both reseating the CPU and GPU to ensure proper contact.
  20. Hello, SOC is sensitive to high voltages also,...

    Hello,

    SOC is sensitive to high voltages also, so you may want to tune values from 1v VSOC with DCOP and work from there. PROCODT can likely be left in Auto.

    Also try adjusting IOD VDDG and CCD...
  21. Replies
    3
    Views
    372

    Reviews should start to land very soon. ETA I...

    Reviews should start to land very soon. ETA I would suggest contacting support for your region.
  22. Sticky: 3501 is the same build that is destined for the...

    3501 is the same build that is destined for the support pages as of this moment, but feel free to wait. There's no pressure on users to update unless they want to.
  23. Replies
    6
    Views
    503

    Use this portal:...

    Use this portal: https://rog.asus.com/motherboards/rog-maximus/rog-maximus-xiii-apex-model/helpdesk_download


    Local pages should have updated.
  24. Sticky: https://www.dropbox.com/s/ktbgx3hlielou59/ROG-CROS...

    https://www.dropbox.com/s/ktbgx3hlielou59/ROG-CROSSHAIR-VIII-FORMULA-ASUS-3501.rar?dl=0
  25. Sticky: The Formula BIOS is above. Flash to it if wanting...

    The Formula BIOS is above. Flash to it if wanting to try AGESA 1.2.0.2. If not, there’s no real reason to flash unless experiencing issues on the platform.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4