Search:

Type: Posts; User: Minsekt

Page 2 of 10 1 2 3 4 5

Search: Search took 0.01 seconds; generated 78982 minute(s) ago.

  1. Replies
    46
    Views
    19,370

    its normal from what i can tell, many skylakes go...

    its normal from what i can tell, many skylakes go up to 1.4v on stock including mine. but mine does 4.7ghz at 1.36v too, try lowering the voltage manually. mine did succesfully run prime 1344 at...
  2. Thread: Q-Fan profile

    by Minsekt
    Replies
    11
    Views
    21,109

    sadly you cant add more than 3- manual qfan...

    sadly you cant add more than 3- manual qfan settings also allow only 3 steps. but i believe speedfan (the program) can add more than 3 steps if youre down to use it... its free.
    like here on their...
  3. you can select gen3 for pcie in bios. then it...

    you can select gen3 for pcie in bios. then it should run at max
  4. Replies
    4
    Views
    2,776

    make sure to try different usb pen drives, some...

    make sure to try different usb pen drives, some just wont work. the only thing you should (you dont really have to) change for the nvme drive is disable csm support.
  5. Replies
    16
    Views
    4,380

    its not "normal" but ive had some boards bent...

    its not "normal" but ive had some boards bent like yours too. screwed it down to my benchtable like normal and they always worked fine, after some time they all where flat again.
    if everything is...
  6. Replies
    15
    Views
    4,683

    are you sure the card itself is not faulty? does...

    are you sure the card itself is not faulty?
    does it happen too if you have only one monitor connected?
    does it happen if youre removing the card and use onboard graphics?
    do you have any...
  7. Replies
    6
    Views
    5,299

    i dont recommend automated driver installers...

    i dont recommend automated driver installers unless you know ecactly what driver you're allowed to install. those programms can mess up your system really quickly.
    on the other hand, if you know...
  8. Replies
    5
    Views
    2,892

    afaik theres no option for that except turning...

    afaik theres no option for that except turning your monitor on like 5seconds after youve turned on the pc.. lol :cool:

    you can either see the rog logo or the post screen. the windows logo shows...
  9. ok looks like ive solved it. like i said S5 Power...

    ok looks like ive solved it. like i said S5 Power State should turn off every led and the board can only boot by pressing the power button on the board itself.
    in my case that happened one out of...
  10. thanks, but no - its not really a keybot issue,...

    thanks, but no - its not really a keybot issue, it does happen too if keybot is disabled/not installed. the board just shutsdown everything and will only boot by pressing the power button on the...
  11. M8F mechanical off power state (all lights off)

    Hey,

    from time to time my M8F shuts down completely (like a mechanical off, G3 power state) when i turn my pc off. like every led is off, like its not connected to a psu. i have S5 power mode...
  12. what qcodes does the board show? how many ram...

    what qcodes does the board show? how many ram sticks do you have installed? did you tried it with only one stick yet? (in dimm a_2) the ram has to be in the grey dimms, just to make sure. also try...
  13. well then its most likely no motherboard/hardware...

    well then its most likely no motherboard/hardware related issue. youll need to setup OBS properly... use CBR and a bitrate up to 2000, dont even think about streaming 1080p if youre not partnered,...
  14. Thread: Help please.

    by Minsekt
    Replies
    2
    Views
    1,690

    according to this image its F90 P02 CFL0717 ...

    according to this image its F90 P02 CFL0717

    http://rog.asus.com/wp-content/uploads/2014/04/M7R_2D.jpg

    but the picture is using the same regulator between the cpu and cpu_opt fan. the one still...
  15. well its not the boards nor the ssds fault that...

    well its not the boards nor the ssds fault that you have to enable csm. temps are normal for the 950 pro, and theyre almost the same on my m8f than on my r5e, which doesnt have a cover. so i wouldnt...
  16. what lags are you getting? latency internet lags...

    what lags are you getting? latency internet lags or fps lags? are you streaming with obs or are you recording local? just dont use more than 2000 bitrate as upload if youre not partnered with twitch....
  17. Replies
    7
    Views
    3,723

    thats a kit for the skylake chipset, theres no...

    thats a kit for the skylake chipset, theres no guarantee it will work on x99 chipset/haswell e with said xmp timings/frequency. skylake can take 3000+ much easier than haswell e. id set the...
  18. Replies
    7
    Views
    4,001

    i hate that wifi antenna, why cant they stick to...

    i hate that wifi antenna, why cant they stick to the antennas like theyre using on the pce-ae68 , looks good overall tho.
  19. Replies
    7
    Views
    3,723

    add some 0.05v increments to your vccsa until it...

    add some 0.05v increments to your vccsa until it works. entering timings manually instead of using xmp might work too, preferably looser timings.
  20. r5e suddently does not detect pcie card including m.2 nvme drive

    ive rma'd it
  21. i got this always when i was overclocking my ram....

    i got this always when i was overclocking my ram. to less voltage, frequency too high. too much/not enough vccsa and i got the same. it showed weird qcodes too like usb/ide check and stuff. but it...
  22. Replies
    11
    Views
    6,479

    no, enter 1.15 for testing and lower the voltage...

    no, enter 1.15 for testing and lower the voltage in 0.05v steps (or better even 0.025v), theres a sweetspot for VCCSA. higher isnt always better here, lower voltage can be improve decetion/stability...
  23. do a cmos reset (press the button on the back of...

    do a cmos reset (press the button on the back of the board) and remove all ram sticks and try it with a single stick in the first slot- test each stick if it works or not. also make sure your cpu...
  24. Replies
    10
    Views
    4,683

    thats because youre propably using a bclk of 100....

    thats because youre propably using a bclk of 100. youll need to set your bclk to 125 to unlock 3300. however on a bclk of 125 you cant use adaptive voltage, so your cpu cant downvolt.
    i think that...
  25. Replies
    10
    Views
    4,683

    check with cpu-z/aida64 inside windows what speed...

    check with cpu-z/aida64 inside windows what speed your ram is running at, bios somehow doesnt always show the right frequencys for my cpu and ram either. (if you where talking about the very right...
Results 26 to 50 of 227
Page 2 of 10 1 2 3 4 5