Search:

Could be it doesn’t like the drive.*
Driver failure on windows loading there’s only one thing at this point. Does that drive website have drivers. If so download them and put them in the folder....

It’s up and operational. Only down side it latency of the VROC raid but Q14K is still more than twice as fast as a stand-alone Sammy 970 plus and sequential are past 500. I was going to use my single...

Thought I left a thank you.*
Mine went from broke dick on upload to actually working!*

You can run both with only X8 on AIC card Â*but still in same boat.Â*
This only applies to the DIMM.2 and once you set it to x16x8x4 it’s all happy. You can run two AIC cards in the X4 (small one...

I didnt have an issue with different VMDs on R6E. with two 900P AIC cards.
I do remember that setting it in the BIOS was worthless. Never did show up right and boot partition just said windows boot....

Thanks,
Between the FW update and driver update my 10GB is working again.

Anyone running VROC on DIMM.2 with a pair of 905P M2 drives?

If so did it take using F6 drivers at win install?*

Encore SLI for two X16 are top two slots.*

You left out the 4 dedicated to the DMI.
If you have a 99XX the last slot can only be X4. No matter which you have X16, X16, X8 or X!^, X16, X4 if the bottom slot is used DIMM.2_2 is not. Its one or...

Yes this can be done. Only thing you cant do is PCIEX4 and DIMM.2_2 at the same time, its one or the other and that shows up in drives section of the BIOS to select one or the other. The M2 drives...

^^^
What he said.
I did the free upgrade on one machine long ago and ended up going back and doing a clean install anyway as I dont care what you do that jump is just too much.
Sounds like your...

I ran the 10G on my RVIE without so much as a burp for more than a year. Now with the Encore edition and drivers from .18 that can with the board to .20 from station drivers. Something as simple as...

What makes you so sure? Is quite possible they screwed up the manual and pin out diagrams. My big issue is clearly labeled 12V ATX and shows reverse polarity of what is on a PCIE cable. If it was...

No need to shut down. I have the board in hand and will look at the connector. *Like I said there is conflicting information. I don’t want to cook a new MOBO. I put in a support ticket but we all...

AI suite is just an interface to the BIOS while up and running which is why I don’t use it. I’ve seen a few stories of this happening after a BIOS update.*

Personally I’m at the staying out of the bargain price end of routers when I expect high performance stage.*

This is a member self help forum. Very seldom do you see ASUS employees posting here.*
My advise with the intel threats?
Disable all the patches and get yourself a decent hardware firewall an stay...

To my knowledge no ASUS laptop is capable of anything past 2400 so buying anything rated higher is a waste of money. Best laptop ram I’ve seen is Gskill ripjaws 2400 in the lowest cas you can find....

This image shows more clearly

84328*

Cut off two of the EPS 8 pin and you have a perfect match

84342Â*

Thanks for your input. See attached photo of 6 pin PCIE cable. The center pin near the latch is not square. It is rounded on the bottom. As stated before the rounded will fit the square hole but not...

They go back and forth and neither will take responsibility nor provide the drivers. Look on winraid for the F6 drivers VROC.*
I ran it for awhile and ditched it. *OK for sequential reads and writes...

VROC is intel drives only. I installed it to two 900P AIC versions. The trick is to have the F6 drivers. You don’t make the array for boot from the BIOS. Two F6 drivers are required at the F6 prompt....

I’ve just ordered one of these boards and want to be prepared for when it gets here

I typically like using all the power connectors.

There is conflicting information over the 6 pin mystery...

Ome way to find out for sure. try both ways and see what temps you get. My experiance with the GPU on air dumping heat into the case its better to pull that heat out the other side which will force...