Search:

Type: Posts; User: 13oots2

Page 1 of 2 1 2

Search: Search took 0.09 seconds.

  1. If your stock temps are that high, I would be...

    If your stock temps are that high, I would be looking at a watercooling solution, you don't have a lot of headroom for any kind of overclock.
  2. Replies
    2
    Views
    298

    Finally got to the bottom of this, my LSI RAID...

    Finally got to the bottom of this, my LSI RAID card has a dual processor and the power requirements were exceeding the standard PCIe supply. Popped in the Molex at the bottom edge of the board and...
  3. Replies
    2
    Views
    298

    Looks like I found the problem, tried my LSI RAID...

    Looks like I found the problem, tried my LSI RAID in a different slot and it died. Had a new LSI turn up today and so far no issues.
  4. Replies
    2
    Views
    298

    PCIe problem R6E

    Am having problems with my LSI RAID card, most times I play a game and use my graphics card at 16x the RAID card disconnects and I lose all the drives connected until next reboot.

    I have 2 PCIe...
  5. Replies
    0
    Views
    226

    Does this seem right R6E 10980XE?

    I have a stable overclock with most of my cores at 4.8gHz but am having to run 2 cores lower due to temps. My overclock is 100% stable, my power draw at the wall seems low under full load, at idle am...
  6. Replies
    1
    Views
    256

    A good friend loaned me the money for a 10980XE,...

    A good friend loaned me the money for a 10980XE, should be here by Wednesday 19th Jan. UK seller had 12 for sale at a price not much more than a 7980XE from China, 30 day money back guarantee too.
    ...
  7. Settings will vary from processor to processor...

    Settings will vary from processor to processor due to slight differences in manufacturing, one processor my do 4.3 another 4.7. You need to do the testing for your chip, it's trial and error.
  8. Replies
    40
    Views
    18,225

    Sticky: Got to be the original Unreal Tournament,...

    Got to be the original Unreal Tournament, belonged to an Anglo Dutch clan back in the day. Am hosting 6 Unreal Tournament servers on my dedicated Linux server.
  9. Replies
    2
    Views
    474

    I have had problems in the distant past with USB...

    I have had problems in the distant past with USB devices causing the system not to boot. Just try with the keyboard plugged in.
  10. Replies
    1
    Views
    256

    7980XE or 10980XE

    Is it worth going for the more expensive 10980XE over the 7980XE? From what I can see there is only about 5% better performance on the 10980, is it really worth it?
  11. Replies
    20
    Views
    921

    I bought another brand of motherboard to try and...

    I bought another brand of motherboard to try and had same issue, it looks like my CPU is the problem.

    Thanks for the help received. 13oots2
  12. 50C is hardly cause for concern, my overclocked...

    50C is hardly cause for concern, my overclocked 7940 hits 80C when rendering in Lightwave. You will find your temps increase when you render out your footage, you may want to run a benchmark such as...
  13. Might be worth you trying the Nvidia Studio...

    Might be worth you trying the Nvidia Studio drivers, they are designed for creative purposes.
  14. Replies
    3
    Views
    932

    Looking online I see different resistance for the...

    Looking online I see different resistance for the DT 770 Pro, if yours are 250 Ohm it may be asking too much for onboard audio to cope with.
  15. Replies
    20
    Views
    921

    I cleaned off the old application of LM and...

    I cleaned off the old application of LM and flushed the CPU with IPA, not a drop of LM anywhere but on the die. When I did it I asked my mate if his wife had any spare nail varnish and covered all...
  16. Replies
    1
    Views
    305

    Solved this one myself, it turned out to be a...

    Solved this one myself, it turned out to be a "Detecting Memory" error code, went in to BIOS and enabled memory training and issue went away.
  17. Replies
    20
    Views
    921

    I think you misunderstood the issue, the two RAM...

    I think you misunderstood the issue, the two RAM slots aren't working at any frequency, hence me thinking it's a hardware problem. There is an option in my BIOS under Tools that allows me to check...
  18. Replies
    20
    Views
    921

    I am of the opinion it is a hardware issue, was...

    I am of the opinion it is a hardware issue, was working perfectly at 1.38V and detecting all my RAM in quad channel. Swapped out Kryonaut for LM and the problems began, as I have noted before there...
  19. Replies
    20
    Views
    921

    Tried running RAM at 2133 and system boots. Go to...

    Tried running RAM at 2133 and system boots. Go to RAM information in the BIOS and the sticks are showing as being in slots, there is no information on speed or capacity, the other sticks read fine....
  20. Replies
    1
    Views
    305

    Cold boot issue Rampage VI Extreme

    I seem to be having no end of problems with this motherboard, perhaps I just bought a lemon off Evilbay. My problem now is when I turn the PC off for the night I now have the dreaded cold boot issue,...
  21. Replies
    20
    Views
    921

    That got me back up to 3467 on the memory quite a...

    That got me back up to 3467 on the memory quite a bit more voltage than I was using before the issue, will tinker later to see if I can get the SA and VCCIO down a little, RAM is at 1.38. Still the...
  22. Replies
    20
    Views
    921

    Totally flushed the CPU with Isopropyl and re-did...

    Totally flushed the CPU with Isopropyl and re-did my application of LM, still the same problem. I am now running 80Gb triple channel, down from 96Gb, aside from RAM overclocking it is perfectly...
  23. Replies
    20
    Views
    921

    Socket is perfect, have magnifying soldering...

    Socket is perfect, have magnifying soldering stand with LED's. Dimm fingers are fine as any stick works in the working slots, have also tried different mounting pressures. This only started after my...
  24. Might be worth trying the drives individually in...

    Might be worth trying the drives individually in the first M.2 slot and seeing if BIOS detects them, you then know if it is a problem with the PCIe settings.
  25. Replies
    20
    Views
    921

    Am going to have another look tomorrow when a new...

    Am going to have another look tomorrow when a new tube of Conductonaut arrives. Will totally flush the CPU with alcohol (probably have a snort of whisky myself) reapply the LM and see what happens, I...
Results 1 to 25 of 33
Page 1 of 2 1 2