Search:

Type: Posts; User: flearider

Page 1 of 9 1 2 3 4

Search: Search took 0.01 seconds.

  1. Thread: usb3 amps

    by flearider
    Replies
    1
    Views
    1,508

    usb3 amps

    are all usb's on the crosshair v 500 m amp ?
  2. Thread: fan header

    by flearider
    Replies
    8
    Views
    2,600

    running them on 3 diff headers atm cpu ,opt1 and...

    running them on 3 diff headers atm cpu ,opt1 and chass 3 in dc mode there only 3 pin .. I'm just going to have to save more cash and get another fan controller .. had to split these off after...
  3. Thread: fan header

    by flearider
    Replies
    8
    Views
    2,600

    thx whitepaw .. but not on about the manual i'll...

    thx whitepaw .. but not on about the manual i'll try and find the tech specs .. I was hoping for 1.5 ish ..
    thx again ..
  4. Thread: fan header

    by flearider
    Replies
    8
    Views
    2,600

    hmm anyone know if that's in the spec sheet .. ...

    hmm anyone know if that's in the spec sheet ..
    if it is 1amp going to leave it ..
  5. Replies
    9
    Views
    4,945

    hmm must have upgraded the nb on the z .. on the...

    hmm must have upgraded the nb on the z .. on the chv it drops my temps by 10-14 deg c
  6. Thread: fan header

    by flearider
    Replies
    8
    Views
    2,600

    fan header

    whats the max amp you can pull off the fan header's .. ? I'd like to put 3x 120's on one there 12v and pull 0.37amp ..

    and are all the headers the same amp value ? could I put 3 more on another...
  7. Replies
    11
    Views
    10,417

    ok so it went back to scan .. they split it onto...

    ok so it went back to scan .. they split it onto 3 test beds ..cpu ...fail ...mem fail ...board ok ...
    they were saying that there having a lot of issues with amd chips atm .. and as for corsair...
  8. Replies
    11
    Views
    10,417

    but that wouldn't show one stick ? it would fault...

    but that wouldn't show one stick ? it would fault both ?
    hmmm might phone him and see if he could up the cp/nb volts .. wish he lived close but 60 miles is a long way to go just to play with pc...
  9. Replies
    11
    Views
    10,417

    mem man set to 1866 .. mem tried in both color...

    mem man set to 1866 .. mem tried in both color slots and each mem tried in single .. mem test no probs ..
    thinking could be board fault ? he's going to pop it into scan tue .. see if theres an issue...
  10. Replies
    11
    Views
    10,417

    hi amd 8320 corsair 2x4gb mem 1866 1.5v...

    hi
    amd 8320
    corsair 2x4gb mem 1866 1.5v CMZ8GX3M2A1866C9R
    psu tx 650
    amd 6870
    boot showing 4 gig
    windows shows 8gig but only 3.93 usable
    cpuz shows 8 gb
    task manager shows 4gb ..
    win 7...
  11. Replies
    11
    Views
    10,417

    sabertooth 990fx v2

    ok so spec'ed my bro a system ..
    now the only problem it's having is this ... bios is giving 2 readings for mem ..the main is showing 4gb .. but under tools/spd it shows both ????
    boot into windows...
  12. Replies
    40
    Views
    28,940

    to give the people what they want even if they...

    to give the people what they want even if they don't need it .. sells more boards , in the long run ...
  13. Thread: P5K Premium

    by flearider
    Replies
    1
    Views
    6,198

    P5K Premium

    ok strange thing happened ..
    had this board in a different case and gave it to my dad ..it was working after the install ..then it went to power light and no boot ..
    tried the bat out and leaving...
  14. wow can't see how your mem will run at that speed...

    wow can't see how your mem will run at that speed with 1.35v ?
    try mem at 11.11.11.34 1.5v 2t
    cpu 23x 1.45v
    freq 215

    then if it works .. start working up slowly
  15. hmm found it hard enough getting cpu stable with...

    hmm found it hard enough getting cpu stable with 16mb mem .. but 32 wow that is going to be tricky ..
    not so much nb/cpu side but just mem .. try increasing .05-.1 because that's where I hit my wall...
  16. problem is it's 5ghz at turbo which is just an...

    problem is it's 5ghz at turbo which is just an overclock for the lazy .. shame really but they do need extra cash ..
    i'm thinking it's not going to beat my 8350 at stable values .. which sits at...
  17. there the future ... well for most sheeple ......

    there the future ... well for most sheeple ... less costs more profit ..
  18. Thread: magic

    by flearider
    Replies
    31
    Views
    12,988

    so there just the cream of the clock 8350's pre...

    so there just the cream of the clock 8350's pre clocked .. mine sits happly at 4.8ghz 1.38v but if they redo the 990 chipset now theres something ..
  19. hmm i'd say up the multi drop the nb ht to 2400...

    hmm i'd say up the multi drop the nb ht to 2400 bring your bus speed down ..
    mem cycle time is wrong should be 32
    whats all the other settings at .. take a pic and post em ..
    ...
  20. Replies
    10
    Views
    5,962

    have you turned off turbo core on the cpu ? your...

    have you turned off turbo core on the cpu ? your overclocking ..
  21. Replies
    2
    Views
    2,394

    can ya tell off the s/n ?din't look on the chip...

    can ya tell off the s/n ?din't look on the chip ..

    and how are you getting on with that sniper low voltage ? can get mine to run at just under 1800 ..
    10,10.10.28 need it to go further any tips ?
  22. Replies
    2
    Views
    2,394

    8350's in .. :)

    so put the 8350 and the nb waterblock in and fired her up .. first did 4.7 just to see it warm up ..
    now straight into the 5ghz club http://valid.canardpc.com/2706796
    will keep on playing with it...
  23. just buy a v then .. not that much has changed

    just buy a v then .. not that much has changed
  24. your still not stable .. things are loading into...

    your still not stable .. things are loading into mem and being lost .. to get 2 seprate sets of mem even tho there the same to run together is hard .. thats why they match 16gb sets at the factory...
  25. just give it a shove and a push...

    just give it a shove and a push...
Results 1 to 25 of 217
Page 1 of 9 1 2 3 4