Search:

Type: Posts; User: Silent Scone@ROG

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds; generated 6 minute(s) ago.

  1. Matched kits will work, that's why they're...

    Matched kits will work, that's why they're matched. What's limited is high-frequency kits in that configuration.

    The reason? It's not possible on this gen to run them that high. Up to 5600 should...
  2. What board? There are a couple of test UEFI ...

    What board? There are a couple of test UEFI builds that were released that might help with a partial remedy, however, it's very unlikely the kits will ever operate at XMP when combined as it wasn't...
  3. They're under the DRAM Timing Configurator page...

    They're under the DRAM Timing Configurator page under Memory Presets.
  4. Probably not documented in the manual, as it...

    Probably not documented in the manual, as it doesn't really have any impact on the end-user experience other than taking an extra second or two.

    It depends on the platform, however, it can be...
  5. Could you take a video of the problem and post it...

    Could you take a video of the problem and post it here? I'd tend to agree with the above, sounds like the issue is with the GPU.

    Take a video, if it seems that way I'll move the thread to the ROG...
  6. At this point given the effective range of...

    At this point given the effective range of running two sticks, I would say that 4x16 6K is not possible on this gen, or it will be highly unobtainable without a good IMC.
  7. Sticky: All sub timings are currently board-controlled. ...

    All sub timings are currently board-controlled.

    6400 C34-38-38-52-1T


    Per C 54/53/52
    Cache 40
    E Core 41 Sync
    MCVVD 1.4
    SA 1.18
  8. Sticky: Hello, both are intrinsically related. Tighten...

    Hello, both are intrinsically related. Tighten down at the maximum frequency you can obtain at 1T.
  9. Some IC don't have thermal probes

    Some IC don't have thermal probes
  10. The Quick Charge header requires a PCIE 6 pin. If...

    The Quick Charge header requires a PCIE 6 pin. If you're not using the USB C header port, there's no need to install the cable. Or equally if you do not plan to plug in devices that will draw 60W
  11. You're not alone. This was a "royal you" post and...

    You're not alone. This was a "royal you" post and not aimed directly at you. If anything you did the right thing by asking before making a purchase!
  12. It's difficult not to sound like a broken record,...

    It's difficult not to sound like a broken record, but Please don't combine memory kits and ask why XMP will not work.

    This is a historical issue enthusiast face that will probably continue....
  13. Replies
    9
    Views
    514

    Hello, so what happens exactly, does it get...

    Hello,

    so what happens exactly, does it get stuck on a Q-Code when updating? What happens when you use EZ Flash from the UEFI? Once the UEFI has completed pre-checks, the system should reboot...
  14. Sticky: Per C 54/53/52 Adaptive 1.37v Cache 40 E Core...

    Per C 54/53/52
    Adaptive 1.37v
    Cache 40
    E Core 41 Sync

    IMCVVD 1.33
    SA 0.98
    VDD 1.48
    VDDQ 1.48
    TX VDDQ 1.52
  15. Hello, You won't. 4X16 6K isn't possible. ...

    Hello,

    You won't. 4X16 6K isn't possible.


    If you're combining memory kits, which isn't recommended, you'll have to tune manually. Aim for between 4400-4800


    Easiest approach is a...
  16. Hello, stick to 1.35 and below if possible. As...

    Hello, stick to 1.35 and below if possible. As with previous iterations, VCCSA is sensitive to excessive voltage so tune methodically.
  17. Hello, Make sure to download and install...

    Hello,

    Make sure to download and install Chipset, Bluetooth, NIC and RST drivers.
  18. Replies
    12
    Views
    1,674

    Hello, Can you please show where in the manual...

    Hello,

    Can you please show where in the manual it states this?

    The power source for the PCIE and the header is shared. If you wish to plug-in devices that draw 60W from the front header, the...
  19. Hello, it sounds as if you are confusing the 8...

    Hello, it sounds as if you are confusing the 8 pin PCIE power cables with the 8 pin EPS for the motherboard. Make sure you are trying to install the correct cable, as the pinout is different. The PSU...
  20. Hello, Those temps are normal, especially...

    Hello,

    Those temps are normal, especially without active airflow. Thanks to the PIMC the modules pack more heat.

    This is well within tolerance, the only "danger" is when pushing the modules to...
  21. Hello, The Q-Code depends on what sleep state...

    Hello,

    The Q-Code depends on what sleep state the system resumed from. It can be impacted by what C-States are active and whether the operating system is utilising hybrid shutdown.

    Ultimately,...
  22. Replies
    23
    Views
    569

    It never really has done, not since DDR4. That...

    It never really has done, not since DDR4. That isn't to say the system won't be stable - but I would almost always run Karhu Ramtest or TM5 also.
  23. Those presets are far tighter than XMP, too....

    Those presets are far tighter than XMP, too. That's what they're there for, and what the board is made for
  24. Replies
    23
    Views
    569

    From experience, I find that having Memtest86...

    From experience, I find that having Memtest86 integrated in the BIOS is a godsend for one reason - not breaking the OS with very unstable settings. Once you get a baseline, you can move on to...
  25. Hello, 16x4 is always going to be tough at...

    Hello,

    16x4 is always going to be tough at those speeds. You're likely going to need more than 1.1v SOC, too. What Q-CODE does the board hang on?

    Test up to 1.2v SOC and see if this helps...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4