Search:

Type: Posts; User: Silent Scone@ROG

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Memtest doesn't give you much more than a...

    Memtest doesn't give you much more than a baseline. Use Karhu Ramtest or TM5
  2. Hopper, it's the power management controller or...

    Hopper, it's the power management controller or PMIC that is now integrated on the module. The memory controller still resides on the CPU.
  3. Replies
    1
    Views
    66

    Hello, Please read the following thread:...

    Hello,


    Please read the following thread: https://rog.asus.com/forum/showthread.php?98041-Understanding-and-using-XMP

    Anything over 3200 on that platform is considered an overclock. If you're...
  4. Advanced Memory settings should be visible at the...

    Advanced Memory settings should be visible at the very bottom of the Extreme Tweaker Page. Highlight auto and enter a higher value, try up to 1.4.
  5. Hello, I assume all these aforementioned tests...

    Hello,

    I assume all these aforementioned tests are at XMP?


    1) Errors at XMP does not mean the DIMM or any other components are faulty. Overclocking never guarantees stability.

    2) 6400 can...
  6. Rule of thumb if one needs to ask then it's best...

    Rule of thumb if one needs to ask then it's best not to. Anything above 5400 with 4 DIMMs is tough, mixing kits will only instigate problems.
  7. They're specific to DRAM IC. i.e Samsung single...

    They're specific to DRAM IC. i.e Samsung single rank, dual rank, and so on.
  8. Matched kits will work, that's why they're...

    Matched kits will work, that's why they're matched. What's limited is high-frequency kits in that configuration.

    The reason? It's not possible on this gen to run them that high. Up to 5600 should...
  9. What board? There are a couple of test UEFI ...

    What board? There are a couple of test UEFI builds that were released that might help with a partial remedy, however, it's very unlikely the kits will ever operate at XMP when combined as it wasn't...
  10. They're under the DRAM Timing Configurator page...

    They're under the DRAM Timing Configurator page under Memory Presets.
  11. Probably not documented in the manual, as it...

    Probably not documented in the manual, as it doesn't really have any impact on the end-user experience other than taking an extra second or two.

    It depends on the platform, however, it can be...
  12. Could you take a video of the problem and post it...

    Could you take a video of the problem and post it here? I'd tend to agree with the above, sounds like the issue is with the GPU.

    Take a video, if it seems that way I'll move the thread to the ROG...
  13. At this point given the effective range of...

    At this point given the effective range of running two sticks, I would say that 4x16 6K is not possible on this gen, or it will be highly unobtainable without a good IMC.
  14. Sticky: All sub timings are currently board-controlled. ...

    All sub timings are currently board-controlled.

    6400 C34-38-38-52-1T


    Per C 54/53/52
    Cache 40
    E Core 41 Sync
    MCVVD 1.4
    SA 1.18
  15. Sticky: Hello, both are intrinsically related. Tighten...

    Hello, both are intrinsically related. Tighten down at the maximum frequency you can obtain at 1T.
  16. Some IC don't have thermal probes

    Some IC don't have thermal probes
  17. The Quick Charge header requires a PCIE 6 pin. If...

    The Quick Charge header requires a PCIE 6 pin. If you're not using the USB C header port, there's no need to install the cable. Or equally if you do not plan to plug in devices that will draw 60W
  18. You're not alone. This was a "royal you" post and...

    You're not alone. This was a "royal you" post and not aimed directly at you. If anything you did the right thing by asking before making a purchase!
  19. It's difficult not to sound like a broken record,...

    It's difficult not to sound like a broken record, but Please don't combine memory kits and ask why XMP will not work.

    This is a historical issue enthusiast face that will probably continue....
  20. Replies
    9
    Views
    546

    Hello, so what happens exactly, does it get...

    Hello,

    so what happens exactly, does it get stuck on a Q-Code when updating? What happens when you use EZ Flash from the UEFI? Once the UEFI has completed pre-checks, the system should reboot...
  21. Sticky: Per C 54/53/52 Adaptive 1.37v Cache 40 E Core...

    Per C 54/53/52
    Adaptive 1.37v
    Cache 40
    E Core 41 Sync

    IMCVVD 1.33
    SA 0.98
    VDD 1.48
    VDDQ 1.48
    TX VDDQ 1.52
  22. Hello, You won't. 4X16 6K isn't possible. ...

    Hello,

    You won't. 4X16 6K isn't possible.


    If you're combining memory kits, which isn't recommended, you'll have to tune manually. Aim for between 4400-4800


    Easiest approach is a...
  23. Hello, stick to 1.35 and below if possible. As...

    Hello, stick to 1.35 and below if possible. As with previous iterations, VCCSA is sensitive to excessive voltage so tune methodically.
  24. Hello, Make sure to download and install...

    Hello,

    Make sure to download and install Chipset, Bluetooth, NIC and RST drivers.
  25. Replies
    12
    Views
    1,753

    Hello, Can you please show where in the manual...

    Hello,

    Can you please show where in the manual it states this?

    The power source for the PCIE and the header is shared. If you wish to plug-in devices that draw 60W from the front header, the...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4