Search:

I just used OC scanner but shut it down because the temp was getting high but I didn't hear the fans speed up. It only got up to around 40% and I terminated the program. There is no cancel or stop...

Is there a way to turn these LEDs off?

I found the solution to my issue. There is a Beta version of LiveDash on the Ryuo support page. It has a small gear icon near the top just for this. I don't remember seeing this on the other version...

I have the Maximus XI Extreme and the Ryuo 240 AIO. I'm havng the same issues with AURA and LiveDash on both the AIO and motherboard OLED. I have the latest software versions installed. I'm using the...

When I shutdown the PC the LiveDash OLED stays on and keeps going through its animation. I didn't see anything in the software or BIOS to tell it to turn off. I have the Maximus XI Extreme. Maybe I...

If I use the Y connector I won't be able to see or adjust the RPMs from the BIOS.

I have the Maximus XI Extreme. The Ryuo is connected to the CPU_FAN. From my understanding this only controls the speed of the pump. I can hear the pump speed increase if I change the CPU fan curve...

I have the Ryuo 240 and in the BIOS I can't view the RPMs or change the speeds of the rad fans because they're connected to the Y connector from the Ryuo pump. So I connected them directly to the...

The fans from the radiator should connect to those connections. Make sure you have the SATA power connected to the PSU and the micro USB to the motherboard. Finally have the 4 pin connected to...

I have the RYUO 240 and was thinking if it makes any difference at what top location its mounted to. Right now its at the front as shown in the image. Would it make any difference if it was near the...

Yes you need to reinstall the heatsink. Also don't forget to remove the blue tape off the thermal pad. Look in the users manual for the ports that might get disabled.

I have the XI Extreme and was looking for a solution. But I guess the only way is to use the onboard M.2 connections to retain x16. I don't like removing those heatsinks because I already seen...

I'm also looking for a clear answer to this. If I have one M.2 in the Dimm.2 riser card how can I still retain the PCIE at 16x?

Where does it say selecting Dimm 2.1 will set the PCIE to run at 8X?

So there is no way to run the Dimm.2 riser card with a single M.2 and have the PCIE at 16x?

The board is within the EATX width standards but they didn't factor in the thickness of the RGB and backplate. If there was no backplate there would be no issues. Phanteks and ASUS did not correctly...

My I/O shield fits perfectly and all the motherboard holes/standoffs were aligned. The back of the I/O is flush with the case opening as it should be. Its just that one of these products is not EATX...

Yeah yours is touching those braces too. Its definitely flexing the motherboard near that end. I know its probably too difficult now with the fans/rad installed but take a look from the top if you...

Maybe the backplate was touching some solder points. That would be a manufacturer defect.

This is how it looks like. I don't really want to start chopping up a new case. As you can see there is some flex near the end. What do you guys think, anything to worry about?

At this point it would be best to get a screw extractor kit. Asus should of used flat-head hex screws. Using Philips on these high end boards is not smart. Why don't you use the Dimm.2 card?

I...

That's interesting. I really don't see how you could get it to fully rest on the back 3 standoffs (closest to the RGB strip). Those braces must be touching the backside of the RGB plate. Are you sure...

I have some clearance issues with the Evolv X and the Maximus XI Extreme. The case is E-ATX compatible but the RGB back plate sticks out just enough to touch those slanted braces (red line). Can I...

I just got my Maximus XI Extreme. I'm installing a Samsung 970 Pro M.2 into the ASUS DIMM.2. Does it matter on which side the M.2 is installed on?

Also, is there a protective film on the LiveDash...

So you mean this mobo does not support S3 sleep/wake modes?

Is there an option on the P9X79 Deluxe board to enable the use of tuning ON or WAKE the PC with a wireless keyboard?