Search:

Type: Posts; User: Falkentyne

Page 1 of 7 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    4
    Views
    152

    For "CPU Fan error" you set CPU Fan to "Ignore"...

    For "CPU Fan error" you set CPU Fan to "Ignore" in monitoring. Then you can use W+Pump or AIO+Pump headers without an issue.

    The aio/wpump headers are for powering pumps directly and having them...
  2. You need to click "Reset layout" or "restore...

    You need to click "Reset layout" or "restore order" in the preferences for panes. Then re-enable "fixed order".
  3. Replies
    227
    Views
    28,711

    Gsync activated-- there's your problem. Gsync...

    Gsync activated--
    there's your problem.
    Gsync will only work at your monitor's refresh rate range. and there are settings where the FPS will get capped at or right below the refresh rate of your...
  4. Replies
    227
    Views
    28,711

    Is your FPS uncapped? Your GPU will not work at...

    Is your FPS uncapped?
    Your GPU will not work at 100% if

    1) it doesn't need to (it's rendering up the maximum the engine allows).
    2) you're using a FPS capping or vertical sync method.
    3) the...
  5. VRM's operate in hundreds of *KHZ* up to 1 mhz...

    VRM's operate in hundreds of *KHZ* up to 1 mhz (1000 khz). A mouse operates up to *1000hz* --ONE khz.
    VRM's have nothing to do with input lag. They have to do with *CPU VCORE* in how the 12v from...
  6. Whoever the hell said it improves input lag...

    Whoever the hell said it improves input lag should be thrown on a tropical island with a half broken Nintendo Switch controller and a solar powered battery AC generator and never be allowed near a...
  7. Replies
    9
    Views
    523

    Well guess what? You can't do that. Deal with...

    Well guess what? You can't do that.
    Deal with it. And maybe try listening to what other people are trying to ask you instead of acting elitist, entitled, fat and lazy.
  8. Replies
    227
    Views
    28,711

    Easy solution 1) Disable C1E and C3 2) Set ASPM...

    Easy solution
    1) Disable C1E and C3
    2) Set ASPM Power management to disabled.
    The biggest culprit of lower GPU core is C3 (sometimes C1E) being enabled. People who refuse to disable C-states...
  9. Core #2, 4 and 6 are always the hottest cores on...

    Core #2, 4 and 6 are always the hottest cores on every 10900k CPU (also applies to 9900k). Core #1 is always the coolest core in prime95 SSE2/AVX/FMA3 small FFT. For some reason, this changes a bit...
  10. Replies
    227
    Views
    28,711

    Renaming is only for bios flashback (e.g. without...

    Renaming is only for bios flashback (e.g. without CPU installed or if you can't boot).
    For Ezflash (normal flash) through BIOS, the bios name can be anything you want.
  11. You forgot Prime95 112k-112k AVX Disabled. ...

    You forgot Prime95 112k-112k AVX Disabled. AIDA64 Stress FPU is not bad for gamers for a realistic AVX test. It's harder to pass than Prime95 AVX disabled small FFT. Realbench 2.56 is harder to...
  12. Replies
    227
    Views
    28,711

    That's good. And did you try the 0704 bios also?

    That's good. And did you try the 0704 bios also?
  13. No need to make two threads asking the exact same...

    No need to make two threads asking the exact same question.
  14. You need a command line flasher to flash these. ...

    You need a command line flasher to flash these. For Gigabyte the file is EFIflash. For Asus, I have absolutely no idea.
    Check win-raid forums and ask there as the people in the bios modding...
  15. Replies
    3
    Views
    147

    What power supply was that? I wasn't aware of...

    What power supply was that?
    I wasn't aware of any decent 1000W's that would do that. What model/brand and when was it purchased?
  16. Replies
    2
    Views
    217

    Normal super i/o resolution. +/- 16mv.

    Normal super i/o resolution. +/- 16mv.
  17. Replies
    227
    Views
    28,711

    The Aquantia nic was wonky as shipped. The...

    The Aquantia nic was wonky as shipped. The original drivers (21.1.18.0) were garbage.

    Remember Shamino is in Taiwan, and their entire team is in Taiwan as far as I know. They have Hinet and I...
  18. Replies
    227
    Views
    28,711

    You already know it's not a bad board. You knew...

    You already know it's not a bad board. You knew this before, it was obvious, but you didn't want to accept that possibility. Everyone saw it's an issue with the Intel nic, either drivers or...
  19. Replies
    227
    Views
    28,711

    Should be okay. You said clean windows install,...

    Should be okay. You said clean windows install, did you install windows on a fresh drive or did you install windows on top of an older installation to keep your files and apps?

    Did you try...
  20. Replies
    227
    Views
    28,711

    What power supply do you have and how old is it?...

    What power supply do you have and how old is it?
    Before RMA'ing the board, can you try a different power supply?
  21. July 5th? First it was June 23. Then it was...

    July 5th? First it was June 23. Then it was June 28th. Now it's July 5th?
    When July 5th comes, it will be July 20th. Mark my words.
  22. Asus can't get the voltage requirements perfect...

    Asus can't get the voltage requirements perfect without an actual stress test done in BIOS and you aren't going to see that. The problem is, besides leakage (one CPU that has the exact same VID and...
  23. Replies
    2
    Views
    168

    As soon as I saw the title I knew you had an...

    As soon as I saw the title I knew you had an Nvidia video card.
    I've only seen this with people with nvidia cards.
    Usually something to do with the power states at idle or load modes or c-states,...
  24. Replies
    11
    Views
    2,478

    I've always wondered if there's any real benefit...

    I've always wondered if there's any real benefit to updating the ME firmware. Are there any specific bugs that are fixed that anyone ever notices? I'm on stock ME firmware (or whatever is embedded...
  25. Seems like it's related to cooler score? You can...

    Seems like it's related to cooler score?
    You can recalibrate or even set a fixed cooler score in the AI Settings.
Results 1 to 25 of 158
Page 1 of 7 1 2 3 4