Search:

Well from your latest pic it shows Qcode 99 which is "Super IO Initialization" and IO meaning anything connected to the board by any interface is not initializing.
I also see a post state led lit,...

Hi drchris :) Qcode 67 is very often DIMM related, but no guarantee as your stop error is the DXE Environment which has failed to initialize.

Reflash your Bios with 1003 cause I doubt that's your...

Qcode 40 is not an error. It is a code indicating that the system is waking up from S4 sleep state.

FYI Kittenjouster you can save profiles in your Bios when OCing, if that is what you meant by "power settings that worked well"
Some poor quality TIM can by runny and separates. It should be a...

Let me know when your up and running and I'll help to get Bios settings correct for stability.
There's not a great deal of headroom but you should be able to get 5.0GHz - 5.2GHz.

Hi Kittenjouster :) An interesting setup.

1. Is that pump/res too small? I haven't seen any OL with your combination, so it's hard to say but from what iv'e heard the Raystorm pro and pump should...

Hi sbowe19 :)

Slightly higher Wattage sbowe19 to 750W-850W Gold certified unit for your setup would be best. Especially for any future expansion.
650w is a bare minimum and don't get Bronze...

Hi Phill and Welcome to ROG.

As you have recognized, the CPU is failing to initialize and all other tests you have made, brings it down to CPU or MB.
One other consideration would be the PSU not...

You should conduct a series of stress tests for instability using AIDA64 to determine Voltages and temperatures whilst under load.
Also download HWMonitor and put them on your desktop side by side....

Hi Erorr :)

64MB at 3200Mhz is a lot to ask of the IMC on your CPU and may not be able to handle it.
Does the system run OK with just 32MB installed.?

First ensure the Fast Boot switch on the MB is turned on.
Check that Fast Boot is also enabled in Bios>Boot>Fast Boot.
Disable PS2 support if using USB keyboard and mouse.
reduce post report to 1...

Did you inspect the MB CPU socket for bent pins, use a magnifier and look for obvious differences in alignment or pins bent down.
If you do, you can carefully bend them back with a toothpick. Do not...

Not only that but Raid 0 provides no security and if one disk fails you loose the lot. For the small performance gain you sacrifice file security.
It's not designed or useful for security,...

Unfortunately Qcode 00 can be one of many things.
First make sure all cables and connections to the MB are secured and populated including 24pin,8pin, and 4pin if available.

I noticed you have...

Hi helpsea :) and Welcome to ROG.

Qcode A2, IDE Detect, error code means it's having trouble detecting or reading connected drives.
Disconnect your drives and reboot the system. This should bring...

Run Memtest86+ from a USB stick to check all your DIMMs.

I assume you have checked that your DIMMs are listed on the ASUS QVL.?
Also that Primary Timings and voltage set correctly in Bios.?
...

Well your DIMMs are listed and tested according to the QVL for your MB. so they conform.
MemTest86+ is the best test run from USB. Both AIDA64 and MemTest86+ are good compared to windows.
Bios 3301...

Your rail voltages are within spec however your VCORE voltage droops a little low.
Try 1.4V with LLC set to high or 75% and test again. Keep an eye on temperatures.

report the result.

Hi rogforum :)

I learned a lot from this article by RAJA: http://rog.asus.com/forum/showthread.php?2162-Overclocking-Using-Offset-Mode-for-CPU-Core-Voltage

You should conduct a series of stress tests, as I think it might be your PSU, unable to cope under load.

I have read this about your PSU. The Wattage may be sufficient however:
The Thermaltake...

I have had these problems in the past. I changed to Waterfox 64bit and updated flash player with Beta updates.
Go here: http://labs.adobe.com/downloads/flashplayer.html

If you have a burnt smell coming from the PSU then chances are high that its toast.
You need an efficient PSU of good quality for your setup.

Don't risk any further damage and swap it out with a...

Please describe what you want to achieve as that splitter is for PCIe and I would not recommend it anyhow.

Normally you access your Bios by continually pressing the delete key off and on during post cycle however your laptop has the F2 function.
You should be able to access Bios with F2 held down.

Check your Task Manager for a process called axinst.exe. End that process and the installer should magically start working.
You should also install as "run as administrator".

Also which version...