Search:

Type: Posts; User: Dreamonic

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds; generated 39 minute(s) ago.

  1. Sticky: I got the same monitor. Had a similar experience...

    I got the same monitor. Had a similar experience out of box; it wasn't the mDP-to-DP cable.

    If I understood what you're saying above, then it's either the "DisplayPort Deep Sleep" function being...
  2. Replies
    27
    Views
    12,972

    So v206 was the System BIOS you were using when...

    So v206 was the System BIOS you were using when you inserted V1 (modified VBIOS version for 670MX) and flashed it?

    What model (SKU) is your VX? What model of screen do you have: AUO, Chi Mei or...
  3. Replies
    27
    Views
    12,972

    Here you go: 670MX VBIOS...

    Here you go: 670MX VBIOS
  4. Replies
    1
    Views
    850

    Hey, I have this notebook as well, and had to...

    Hey,

    I have this notebook as well, and had to do some research on this at the time. When the Notebook is connected to the dock (both AC adapters plugged in) and power button is pressed, should...
  5. Not at all. I understand the situation. This...

    Not at all. I understand the situation.

    This is a frustrating problem to troubleshoot given how long you've been going at it. So I understand your time spent in the matter, attempting fixes that...
  6. Replies
    15
    Views
    2,508

    Not sure how I missed this thread. Yes, the...

    Not sure how I missed this thread.

    Yes, the G75 models can be upgraded to the following: Link

    What is weird is that behavior of your system after the screen replacement closely compares to a...
  7. Then it looks like someone used the wrong BIOS...

    Then it looks like someone used the wrong BIOS image for your replacement MB. I have not seen a JH BIOS working on a JW MB before but I already knew it was possible due to the fact both notebooks...
  8. Are you certain the MB you got was a JW model?...

    Are you certain the MB you got was a JW model? What does the stamp show it as on the PCB?

    It could be A) the MB you got was a JW model with the JH BIOS flashed on or B) the MB you got was indeed...
  9. Regarding recent posts in this thread, especially...

    Regarding recent posts in this thread, especially for the RB71 models that have the 6700HQ CPU specifically, the Extreme profile in the Gaming Center has no importance like it does with the 6820HK...
  10. Have a read here...

    Have a read here.
  11. While troubleshooting with a member on my forum...

    While troubleshooting with a member on my forum over a thermal issue he was having (short story here), it turned out to be poorly sealed heatpipes being the root of the issue. Didn't matter how many...
  12. Replies
    16
    Views
    6,369

    Do you remember when the KB lights were working...

    Do you remember when the KB lights were working until they weren't? Backtrack the best you can. Was there any changes in the BIOS made by you or recent BIOS updates applied prior to the KB lights no...
  13. As I imagined, NBFC would help enough. Decent...

    As I imagined, NBFC would help enough. Decent change in score! You were in the mid 90s at one point with your cores though. GPU temperature reaching lower 90s as well. You sir are in need of a...
  14. Hey Jamesgz, You're most likely thermal...

    Hey Jamesgz,

    You're most likely thermal throttling at load. Monitor your CPU and GPU temps on your next benchmark run and then post those results back here.

    The 4720HQ runs very warm in that...
  15. Replies
    26
    Views
    14,751

    1-A. I personally use MX-4 for GPU VRM and VRAM...

    1-A. I personally use MX-4 for GPU VRM and VRAM and then apply Grizzly Conductonaut on the GPU and CPU die.
    1-B. This completely depends on the thermal compound you buy as some are thicker in...
  16. Replies
    26
    Views
    14,751

    Nicely done!

    Nicely done!
  17. Replies
    26
    Views
    14,751

    To answer your questions Gps3dx: 1. Grizzly...

    To answer your questions Gps3dx:

    1. Grizzly Conductonaut 5g / Grizzly Kryonaut 11.1g / Gelid GC-Extreme 3.5g (x2) / ARCTIC MX-4 20g
    2. The right amount is determined by the gap between the...
  18. Hey, I just read your message from VG....

    Hey,

    I just read your message from VG. Appreciate it. I'm glad our guide helped you in recovering your specific KB lights problem!
  19. Replies
    335
    Views
    170,074

    Hey Arkit0, We scaled voltage for the...

    Hey Arkit0,


    We scaled voltage for the additional boost states up to 1168mV, as we even set 1306Mhz for final boost state as this was stable at even 1137mV. It may show 1176Mhz in GPU-Z, but it...
  20. Replies
    335
    Views
    170,074

    Try running DDU and do a clean install of your...

    Try running DDU and do a clean install of your display drivers first, as it may correct this since the slider IS available up to 89C (meaning the flash was successful). Also confirm in GPU-Z that...
  21. Replies
    58
    Views
    39,679

    Absolutely, G75VW 8MB BIOS 223 here...

    Absolutely,

    G75VW 8MB BIOS 223 here.

    So as long as I have available time to problem solve with the eGPU project. That would be a great idea.

    One of the joys of being able to experiment with...
  22. Replies
    58
    Views
    39,679

    Good job getting prepared! It depends on the...

    Good job getting prepared!

    It depends on the state of the brick. Typically with a brick such as yours, the entire main block is corrupted, leading to the no power state after flashing. The power...
  23. Replies
    58
    Views
    39,679

    Also to note, the 25 SPI adapter (blue PCB) has...

    Also to note, the 25 SPI adapter (blue PCB) has to be inserted into the ZIF socket following the same configuration as well.

    Next to the ZIF in the picture above (to the right) are two SOIC...
  24. Replies
    58
    Views
    39,679

    Based on the programmer SOIC support, the wiring...

    Based on the programmer SOIC support, the wiring is supposed to already be in correct configuration, but it's still best to confirm it.

    The red stripe on the ribbon cable is to represent Pin#1...
  25. Replies
    58
    Views
    39,679

    If it's unreadable by the programmer, then either...

    If it's unreadable by the programmer, then either wires are not correct, VCC doesn't need to be used and AC adapter plugged in does. Rarely will it be so corrupted that the programmer cannot read...
Results 1 to 25 of 476
Page 1 of 20 1 2 3 4