Search:

Type: Posts; User: Falkentyne

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. A too high cache ratio will just generate a...

    A too high cache ratio will just generate a "clock watchdog timeout" (0x101), or a Stop 0x124 (WHEA uncorrectable error). Stop 0x124 on these platforms is very often cache related. Clock watchdog...
  2. Replies
    17
    Views
    622

    Looks like it cant go to 6 digits or it's bugged...

    Looks like it cant go to 6 digits or it's bugged on HEDT?
  3. Replies
    17
    Views
    622

    Why are the scores much lower (and latency much...

    Why are the scores much lower (and latency much higher) than what AIDA64 shows?
    I was getting 31000 read and 35000 write and 50.1ns. AIDA64 is 49500 read and 51000 write and 41.2ns.

    That's a...
  4. Replies
    9
    Views
    438

    I already told you why it happens and you...

    I already told you why it happens and you completely ignored me. Maybe it's all over your head. Do you know how power plane impedance works?
    First let's explain voltage loadline resistance. ...
  5. Replies
    9
    Views
    438

    The last two posts are wrong. NO LLC levels...

    The last two posts are wrong.
    NO LLC levels overvolt.
    Transient spikes isn't the same as what you call overvolting from reading vcore from a badly calibrated SIO chip (Pre Maximus XI boards).
    LLC8...
  6. Disable Asus EC support in your monitoring tools,...

    Disable Asus EC support in your monitoring tools, close HWinfo64 *or* disable Asus EC in HWinfo64.
    or just uninstall the Asus windows monitoring tools you have installed.
  7. Replies
    6
    Views
    414

    What's PPL? You have a lot of typos here. 2.6v?...

    What's PPL?
    You have a lot of typos here. 2.6v? What? A processor would be destroyed if any voltage were that high. Even on sub-zero.
  8. All this is explained here....

    All this is explained here.
    https://rog.asus.com/forum/showthread.php?106375-MCE-explanations-and-others

    The VID changes when the multiplier goes up, thus the change in voltage. And adaptive...
  9. Replies
    1
    Views
    270

    This setting has zero actual effect on temps and...

    This setting has zero actual effect on temps and just skews the DTS sensors calibration (not all of them); some will report a lower temp than others. PLL OC can go down to 1.110v, before the system...
  10. Replies
    4
    Views
    514

    CPU's are rated up to 100C, which is tjunction,...

    CPU's are rated up to 100C, which is tjunction, although some boards set it to 95C. So running at 98 to 99C is no problem at low volts. Technically, 125C is the thermal trip (instant shutoff of all...
  11. Replies
    24
    Views
    1,127

    He gave you the most detailed answer anyone...

    He gave you the most detailed answer anyone could, and answered *all* of your questions precisely. But clearly you don't like the answer since you're unhappy with your board, and blaming HIM for...
  12. Replies
    341
    Views
    66,404

    Switchable Graphics, aka Optimus. These options...

    Switchable Graphics, aka Optimus.
    These options are in the base bios code from AMI. Probably don't want to select SG. It's for laptops that have the outputs muxed through the iGPU with dGPU...
  13. @jab383 already said everything that needs to be...

    @jab383 already said everything that needs to be said. You (OP) didn't give us any system information at all, despite writing a gigantic wall of text. We have no idea what you're using except "uh,...
  14. It's not the fact that the iGPU is disabled....

    It's not the fact that the iGPU is disabled.
    It's the new stepping. Notice the "R0"?
    The 9900K's with iGPU will also get that stepping.
  15. Increase vcore or raise loadline calibration by...

    Increase vcore or raise loadline calibration by one level.
  16. You can't. VID is hardwired into the CPU. You...

    You can't. VID is hardwired into the CPU. You override VID by using manual voltage. Period.

    If you don't want to use manual voltage, then all you can do is limit how much the "VID" is boosted...
  17. Your CPU VID won't be lower than your default...

    Your CPU VID won't be lower than your default pre-programmed CPU VID in adaptive mode.
    Additional turbo voltage in adaptive mode will also not go below your CPU VID (which depends on the...
  18. Replies
    341
    Views
    66,404

    What new things? What new settings did you see?...

    What new things?
    What new settings did you see?
    And you really should be using HWinfo64, and have it running in sensor mode when doing the XTU and Realbench 2.56 stress tests. Look for logged WHEA...
  19. This has already been answered. And your load...

    This has already been answered.
    And your load graph you posted is basically useless.
    You need an oscillioscope for these kind of tests. It has to be at least 50 mhz and (40us or ms (??) sampling...
  20. completely wrong. Default VID is based on BOTH...

    completely wrong.
    Default VID is based on BOTH CPU Cache ratio and core ratio. I suspect you are on stock F4 bios which uses a MUCH higher cache ratio than normal, which will cause a higher VID...
  21. You're complaining a lot yet you're refusing to...

    You're complaining a lot yet you're refusing to do what I asked you to do.
    That's not helping anyone. It's unhelpful if you won't cooperate with people asking you do specific tests.
    Set your bios...
  22. Did you change the internal AC/DC loadlines to...

    Did you change the internal AC/DC loadlines to 0.01 or anything?
    I believe one setting on the Asus board will set these to 0.01 automatically.
    That error means your CPU voltage is too low, but...
  23. Replies
    3
    Views
    332

    The PCIE lock should usually be pressed to the...

    The PCIE lock should usually be pressed to the side going towards the CPU, towards the cpu if it's a side tab, or otherwise pressed down if not.
    On most older boards (not sure about all), the latch...
  24. I know English isn't a first language for you,...

    I know English isn't a first language for you, but you really need to listen and stop arguing and start trusting.
    LLC3: 1.340v bios will be about 1.220v at full load (VCC_SENSE measurement). Yes...
  25. Do not use LLC7 at any vcore (bios) higher than...

    Do not use LLC7 at any vcore (bios) higher than 1.250v ! Use LLC6 and a higher bios voltage like 1.35v is much safer! I personally would not use LLC7 any higher than 1.20v bios, and LLC8 any...
Results 1 to 25 of 64
Page 1 of 3 1 2 3