Search:

Thanks Morph, I'm on it. I enjoy reading.

Edit :
After reading that link above, and the DDR4 guide by HISEVILNESS,.. I now have a much better approach, understanding for adjusting all timings.
...

I adjusted tRAS from 37 down to 35, and dropped Command Rate to CR1,.. and got some strange results, Read went up nicely, but Write & Copy took a huge hit dropping,.. Latency also dropped to sub 40...

Thanks, done deal.

87211

Read, Write, and Copy are still going up, and Latency is basically the same, perhaps .8 ns lower.

87212

RTL (CHA) D0 74
D1 69
RTL (CHB) D0 74
D1 71
IO-L (CHA) D0 4
D1 14
IO-L (CHB) D0 4
D1 15

Any suggestions or advice would...

Was hoping someone would answer that for you, as currently I have tRFC 2 & 4 set to Auto, along with the Third Timings.

87194

I put the 3733 profile on the back burner, started working on a...

Congrats, nicely done sir.

I'm getting similar numbers running XMP profile @ 3600MHz, I really don't see much latency, performance benefit running below 4133MHz, up to 4600MHz.

87184

I've been test running new 1002 BIOS, setting up some memory profiles.

These settings are Prime95 stable on my rig.

@ 3733 MHz 13-17-17-33 (CL-RCD-RP-RAS) / 57-617-459-283-9-6-38 ...

Loaded it this morning, seems to be working fine on Extreme board.

87168

Other than being vary lucky and buying a new 30-series card from a retailer, or paying a several thousand dollar markup and buying from a scalper, there are a few other options. Best option is using...

USB BIOS Flashback, no CPU or memory needed,..

https://rog.asus.com/technology/republic-of-gamers-motherboard-innovations/usb-bios-flashback/

I had the same issue after installing RTX 3090 FE card, and discovered the issue was due to having a USB charging device plugged into my rear IO USB port.

Vary strange, as I have had the USB...

Hello Martinav,

For you to do a RAID with NVMe SSDs, you need the drives to be mapped to the chipset or to a storage controller that supports the feature.

Skylake-X CPUs support either 28 or 44...

Generally the Apple Keyboard & Mouse wasn't designed to work with anything but Mac, did you have any issues installing the Utilities software? The mouse and keyboard will work without the software,...

A few adjustments in OSD Setup & Calibration might help colors seeming washed out,.. the PG27UQ is a 120Hz monitor, when you engage the overclock, it will run reliably at 144Hz, but it will only do...

Just started playing Rainbow Six Siege a few days ago,.. waiting for Cyberpunk 2077 release. :)

I have same issue 4-quick beeps after installing 3090 FE card, I confirmed pulling 3090, putting back in old GPU and the beeps go away.

The beeps do not seem to cause any issues, as my system...

Hello,

Percentage and fan speed cannot be calculated. Every fan responds to PWM signal in their own way. Even if their speed range was identical, one fan can run 1200 @ 20% and another fan run...

When you were in your BIOS did you check Advanced\Onboard Devices Configuration, there should be a tab for USB power delivery in soft OFF state (S5) with a drop down menu, can you confirm this...

Let's try going to BIOS, Advanced, and than Advanced\Onboard Devices Configuration,.. scroll down to LED lighting and When system is in sleep, hibernate or soft off states and click the drop down...

I see a few listed as used for $200 on Amazon, you might find a new board on Ebay. Good Luck

You can check your BIOS for Stealth Mode, Onboard Devices settings,.. my board also has onboard RGB jumpers/switches that are set to ON in default, and can be switched to OFF to shut down the RGB...

[QUOTE=Carlyle2020;820346]sounds like samsung b-die to me :)

Micron ICs.

86991

+1,.. It's not the board you have to worry about,..

It's if your CPU has a strong enough memory...

Good question, just be carful not all Motherboards and RAM are equal when it comes to voltage.

I run my memory at 1.5V 24/7 and have bumped voltage up to 1.75-1.9V several times benchmarking...

+1 not impressed with the design, no backplate.

I would preferer not having a 12-pin plug on the front of block, would have liked to see inlet/outlet on the front and the 12-pin on the right...

Here you go, Asus today officially unveils it's new EKWB series cards with preinstalled water blocks. https://videocardz.com/newz/asus-unveils-geforce-rtx-3070-ekwb-with-12-pin-power-connector