Search:

4x16GB with 3600 1:1 FCLK might be hard for some CPU to obtain without considerable SOC voltage. Depends on the CPU, but it's achievable. Be sure to test properly with Kahru RAM Test or HCI Memtest...

It's best to use UEFI to control fan headers for minimal overhead. Should be apparent when entering the BIOS.

Hello, you want to set a manual SOC voltage. Try between 1.05 and 1.15v. For four modules of 16, you will likely require the higher side.

You may also need to adjust IOD VDDG and CCD. Try...

These are fairly bold claims...

I haven't seen the behavior you are seeing on the 570-E and I have two to hand. Temperatures land in the 60c region...

See the below review, also similar...

Hello,

Remove memory overclocking by disabling DOCP/ XMP and leave the system at optimised defaults to see if the issue persists.

It is important to note that, even with improvements over last gen, not all 5000 series CPUs will reach 1900FCLK unconditionally. You can try adjust VSOC to around 1.15v and try VDDG around 1 to 1.05...

Hello,

Have you checked the power consumption of the card?

These can be found in Computer Management Under Windows Logs > System.

Hello,

Reachbench makes use of X256 encoding which uses AVX2, these extensions are known for pulling more current than conventional stress test routines. In regards to clocks and temperature, you...

Hi folks,

The table below shows which UEFI build you will need for AGESA 1180.

These will become available via the support pages over the next 48 hours.


87157

I'm currently using Firefox and am not experiencing this issue. Please disable any adblockers as this can play havoc with some capcha codes

Hello,

A further VBIOS update will be coming to address the fan threshold. Expect it to drop on the support pages within an ETA of a month's time.

Hello,

A further VBIOS update will be coming to address the fan threshold. Expect it to drop on the support pages within an ETA of a month's time.

Either Ryzen Master or HWInfo depending on what sensors you wish to monitor.

Hi,

Having used a GEN 3.0 riser cable (@ GEN3) with an RTX 3080 on the CH8 and using GEN 4.0 conventionally, the performance was within margin of error.

This is because the board is posting in safe mode as you're at the edge of stability (as Shamino mentioned).

Hello,

The CPU is very unlikely to be faulty. You need to tune the memory or revert to an UEFI that is more stable for the time being with the kits in question.

Use Karhu Ram Test to establish...

Hello,

Unfortunately, mixing memory kits is often ill-advised for this very reason as the memory vendors bin the kits in the density they are sold in. As a result, they is no guarantee they will...

As long as you're confident mounting pressure is fine, then there's nothing untoward about those temperatures. Anything up to 10 degree in variance is not uncommon.

Not everyone is experiencing the same issues as you are, so the route cause is unclear for individual cases. I have no instability issues on my CH8 / 5950X setup whatsoever on any of these builds...

I would highly recommend anyone experiencing instability problems to shift to Karhu RAM Test version 1.1.0.0 or greater. This is by far the most effective memory stress test for Zen-based platforms...

I would highly recommend anyone experiencing instability problems to shift to Karhu RAM Test version 1.1.0.0 or greater. This is by far the most effective memory stress test for Zen-based platforms...

According to AMD the feature is set to debut in AGESA revision 1180.

Hello, I would first double-check that the cooler is correctly seated with even mounting pressure and that the pump is running. HWinfo should display speed via the attached header.

Switched from 3950 to 5950X here on the CH8 and not experienced those problems. You may want to reinstall Armory Crate, also make sure the system is stable. Memory instability can cause the lighting...