Search:

Type: Posts; User: Buellersdayoff

Page 4 of 5 1 2 3 4 5

Search: Search took 0.00 seconds; generated 40693 minute(s) ago.

  1. Replies
    4
    Views
    3,803

    The lower slot would be better for temperatures,...

    The lower slot would be better for temperatures, further away from cpu & gpu heat
  2. Apparently ai-suite is causing this issue also,...

    Apparently ai-suite is causing this issue also, uninstall or update to latest
  3. It's usually a memory issue, so to rule that out...

    It's usually a memory issue, so to rule that out run memory at stock speeds and see how it goes.
    OR
    bump up vccio & sa voltages a little until stable. Stick to 1.2 @ most for now, it will also...
  4. Replies
    63
    Views
    12,765

    Time to enjoy it now ☺️

    Time to enjoy it now ☺️
  5. Replies
    8
    Views
    7,451

    Per core overclock is similar to what Intel does...

    Per core overclock is similar to what Intel does as standard eg. a higher frequency for one (or in our case two) cores loaded and a lower frequency for all core/heavy load. Lower LLC level on asus...
  6. Replies
    8
    Views
    7,451

    LLC 5 usually gives you the closest to what you...

    LLC 5 usually gives you the closest to what you set up in bios, try the settings from my previous post
  7. Replies
    8
    Views
    7,451

    If you are OK with using 1.4v but wanted to...

    If you are OK with using 1.4v but wanted to reduce temps a little. Try adaptive voltage 1.45v with -0.05 and set up a per core 46.46.44.44 with llc ~2, cache 8-44. You may need to try slightly...
  8. XMP memory profile can be applied also. If you...

    XMP memory profile can be applied also.
    If you do decide to overclock or tune it yourself then http://www.overclock.net/t/1570313/skylake-overclocking-guide-with-statistics will help
  9. Replies
    58
    Views
    15,738

    As suggested definitely try the rad fans as...

    As suggested definitely try the rad fans as intake, Also remove one gpu for a period to see what results are achieved. Just a few easy things to try before you go buy a new cooler.
  10. Replies
    63
    Views
    12,765

    Try running the ram @ 3000 mhz. I've got the same...

    Try running the ram @ 3000 mhz. I've got the same ram but on a Z170 board and had issues with latest bios and flashed back to the previous version. XMP was problematic on any bios version and...
  11. Replies
    63
    Views
    12,765

    Any Q codes when it does not boot? Possible to...

    Any Q codes when it does not boot? Possible to try flash back to previous bios version? Try run the ram @ 3000 mhz
  12. Fan expert uses a different sensor (socket temp?)...

    Fan expert uses a different sensor (socket temp?) as opposed to the other programs reading core temps. Run some gaming benchmarks in windowed mode, adjust your curve to suit your needs. Take note of...
  13. Replies
    13
    Views
    5,135

    Yes, but you can connect the hub to any other...

    Yes, but you can connect the hub to any other 4pin pwm connector on the motherboard and control the case fans independently
  14. Replies
    13
    Views
    5,135

    Yes... If you are using a pwm signal from the...

    Yes... If you are using a pwm signal from the motherboard.
  15. Replies
    13
    Views
    5,135

    Keep in mind that the phanteks hub is very...

    Keep in mind that the phanteks hub is very limited in its range. Lowest pwm is something like 60% or approximately 5 or 6 volts, don't quote me I just remember it being very limited and stopped using...
  16. Replies
    13
    Views
    5,135

    If it's a 4 pin header it should be pwm and have...

    If it's a 4 pin header it should be pwm and have the same curve as the CPU header. With that phanteks hub you can use any 4 pin pwm header, just make sure it's set to pwm in bios.
  17. 2202 seems fine for me, I did a clear cmos before...

    2202 seems fine for me, I did a clear cmos before flashing and again after, then applied my settings. One thing though is I don't change everything in one go.
  18. Same for me... Had to roll back to 2202....

    Same for me... Had to roll back to 2202. Instability with my ram was the main issue.
  19. Replies
    7
    Views
    2,586

    Early adopters, just gotta have that new gear as...

    Early adopters, just gotta have that new gear as soon as it comes out. Bragging rights...that's why lol
  20. Replies
    18
    Views
    9,804

    Press and hold the Shift key on your keyboard and...

    Press and hold the Shift key on your keyboard and click the Restart button.
    driver-signature-enforcement-restart
    Choose Troubleshoot > Advanced options > Startup Settings and click the Restart...
  21. https://youtu.be/CiYQqNiqQKU Rx480 getting...

    https://youtu.be/CiYQqNiqQKU
    Rx480 getting better with drivers
  22. I used one of these...

    I used one of these...
  23. Run the game for a while and when you notice...

    Run the game for a while and when you notice problems go back to afterburner then screen shot, also scroll down and take a second screen to get the complete graph
  24. Bummer about the CPU, hope you get it sorted out.

    Bummer about the CPU, hope you get it sorted out.
  25. I think you will need to rma the board, had the...

    I think you will need to rma the board, had the same issue with my previous gene viii. I just picked up a new one while I sent "00" board in for service and I'm glad I did because after selling the...
Results 76 to 100 of 117
Page 4 of 5 1 2 3 4 5