Search:

Type: Posts; User: grum_feast

Search: Search took 0.02 seconds.

  1. One last thing, overclocking my freesync range to...

    One last thing, overclocking my freesync range to 57-144hz is still working.
  2. Alright, got everything back from Asus today so...

    Alright, got everything back from Asus today so here's my report.

    They went ahead and sent me a brand new MG279Q. No dead pixels that I can see and the backlight has less halo than the one I had...
  3. I'm ok with the additional wait since shipping...

    I'm ok with the additional wait since shipping was paid for and thanks for the escalation Bahz.

    A bit more details on what it was doing before I sent it back again btw... With the CRU settings...
  4. Got a new shipping label from tech support so...

    Got a new shipping label from tech support so I'll be shipping the monitor back out today. Crossing my fingers again.
  5. Sigh... well I got the monitor back and so far...

    Sigh... well I got the monitor back and so far the strange line in the middle hasn't shown up. However, I now have an entire column of dead pixels stuck on red that are about 1/3rd from the left...
  6. I just saw today that my RMA is done so I should...

    I just saw today that my RMA is done so I should be getting it back in about a week. I'll be sure to post results though it sounds like this is the fix that's going to work for everyone based on...
  7. Yes, I've decided I'm going to give RMAing one...

    Yes, I've decided I'm going to give RMAing one more shot. I've replied to them and am just waiting on the shipping label now.
  8. Yes, the 143hz solution is still working for me.

    Yes, the 143hz solution is still working for me.
  9. According to the e-mail I got from tech support...

    According to the e-mail I got from tech support they did apply the firmware update to mine.
  10. Last time I talked to Asus tech support over...

    Last time I talked to Asus tech support over e-mail they did want me to send my monitor back in for a second attempt at repairs (they didn't specify what the repairs would be). However, I too am...
  11. Hoping then that more people post their RMA...

    Hoping then that more people post their RMA results since that would help.
  12. Just got done testing my old Asus VS278Q with my...

    Just got done testing my old Asus VS278Q with my Fury over the same DP cable I've been using on the MG279Q. Made sure settings were stock then turned it off and on 40 times. No line unsurprisingly.
    ...
  13. Been going through all the standard...

    Been going through all the standard troubleshooting steps with tech support but not making much progress so far. Right now they're trying to say that my Fury card is defective since I don't get the...
  14. No problem YiRz99. Here's step by step exactly...

    No problem YiRz99. Here's step by step exactly what I did on mine since it was pretty baffling the first time I used it. I can also send you my saved CRU settings file if you want to PM me your...
  15. Something I never noticed before on stock...

    Something I never noticed before on stock settings. When I open up the OSD sometimes it reports that the monitor thinks it's running at 2568x1440 (when obviously it should be 2560). This seems...
  16. I just ran on stock settings for awhile at both...

    I just ran on stock settings for awhile at both 90 and 144hz. Text in Windows 10 and Chrome still seem ok on mine (even when the line shows up).
  17. Tribullet, I haven't personally noticed any...

    Tribullet, I haven't personally noticed any blurry text issues on my end. I'll try stock settings again when I get the chance and see if that makes text look any different.
  18. Also, just to help out anyone else in this thread...

    Also, just to help out anyone else in this thread who can't get the line to go away with CRU, I had to set my refresh rate to 142.856hz to fully get rid of it. Setting the mode to exactly 143hz...
  19. UPDATE: I've got Freesync working at 143hz...

    UPDATE:

    I've got Freesync working at 143hz again with no glitching. That one was actually 100% my fault. When I was re-entering my settings into CRU I forgot that I had my range limit set to...
  20. I just got my MG279Q back from RMA (using it with...

    I just got my MG279Q back from RMA (using it with a Sapphire NITRO R9 Fury). Unfortunately, not only is the line still appearing (tested at 90hz and 144hz), but I have also lost the ability to get...
Results 1 to 20 of 21