Search:

Type: Posts; User: Carlyle2020

Page 1 of 5 1 2 3 4

Search: Search took 0.00 seconds; generated 3 minute(s) ago.

  1. Well Sir if you do not feel the need to share...

    Well Sir if you do not feel the need to share your Bios config in written or picture form you seem to have figured it out all by yourself.

    Good luck RMAing ... the board? ... the SSDs?

    Rgds...
  2. Thanks, i will wait for more info. That it...

    Thanks,

    i will wait for more info.
    That it boots until this point let's me believe that it is rather a Bios missconfiguration than an RMA worthy issue.

    There is hope :)

    Rgds
    Carlyle
  3. Please post Bios pics from anything concerning...

    Please post Bios pics from anything concerning drives, boot order and boot config.

    The OS:
    - Freshly installed in this rig?
    - rather uninstalled from another rig?
    - If it was transplanted, in...
  4. ... Isn't there a mention in the manual about...

    ... Isn't there a mention in the manual about ports 1, 5 and 6 sharing resources ?
  5. It must be a wrong Bios setting since i get full...

    It must be a wrong Bios setting since i get full speed on both SSDs.

    Confirmed via the tool you suggested.

    I checked my Bios. I didn't find something to point out except that "Hyper M.2 xxx"...
  6. voltage table question for "CPU stand by" with 8086k/Z390 apex/per clock OC/ X53

    Hello there,

    I am running manual vcore with all other power saving functions activated and Svid off/MCE-on (800-5300Mhrz during testing):

    My '8086k', Bios v.1302 does misbehave a little if I...
  7. Replies
    5
    Views
    192

    ( After reading this kindly hit the "one page...

    ( After reading this kindly hit the "one page back" button on your browser :rolleyes: )

    :) Our dear Shamino did take his time and has put up a really comprehensible sticky thread about MCE and...
  8. Since not all z 370 and 390 VRMs are built equal...

    Since not all z 370 and 390 VRMs are built equal one cannot make that comparison in general.

    It also would be worth a try to lower the LLC by one and rather up the vcore until it is stable again....
  9. Replies
    5
    Views
    192

    Not to paraphrase Batman Sir, but what you...

    Not to paraphrase Batman Sir,

    but what you want is maybe not what you need here.

    So the new is not like the old: check.

    Kindly use LLC5 and manual vcore and start fresh to find a stable...
  10. It should. Push the clear-CMOS button for good...

    It should.
    Push the clear-CMOS button for good luck and don't be scared if the rig (maybe) restarts itself once or twice.
  11. Replies
    1
    Views
    141

    ? I had those fluctuations/droops with my x370...

    ? I had those fluctuations/droops with my x370 hero as well.

    All is good. Your board eats tight RAM timings like a champ and it is very forgiving during testing.

    ;-) I should know.

    Rgds...
  12. Replies
    11
    Views
    423

    IF it gets a little worse day by day, it could be...

    IF it gets a little worse day by day, it could be the PSU is on its way out.

    ...Maybe i assume this because it happened to me a month ago.

    So keep your assesment fluid please.

    Rgds
    Carlyle
  13. Replies
    23
    Views
    2,532

    Well it runs smooth with my 8700k and 8086k....

    Well it runs smooth with my 8700k and 8086k.
    Anyone having issues and has no 9900k?
  14. So you still have LN2 mode activated? ......

    So you still have LN2 mode activated?
    ... Doesn't one loose all waranty by activating it?
    Please turn it off.
    If you do not find a solution with LN2 mode turned off then you may already have...
  15. Hi Mappi75, i am a novice at subtiming ...

    Hi Mappi75,

    i am a novice at subtiming tweaking. So my tweak is rather basic. Lastly i want to point out that my motherboard is very forgiving concerning ram settings. So please try out at...
  16. Replies
    356
    Views
    72,803

    My 8086 runs fine. With and without power saving...

    My 8086 runs fine. With and without power saving settings.
    ... Isn't the "turbo" function diretcly below the speed step setting? *wink, wink*

    Regards
    Carlyle
  17. The PSU is absolute overkill for your system....

    The PSU is absolute overkill for your system.
    Overkill as in: You are running your system outside of the PSUs efficiency curve. You are wasting power on idle and on full load.
    !Matter it does not!...
  18. Far too early to tell. The Watchdog Error lets...

    Far too early to tell.
    The Watchdog Error lets me blelieve that you do not have faulty hardware. Rather some unfortunate Bios setting.

    So First steps:
    Check the AIO !
    IF the PSU has a self...
  19. Replies
    5
    Views
    304

    Well Sir, simply try it out. IF it does cut...

    Well Sir,

    simply try it out.
    IF it does cut the lanes simply sand down the DIMM.2 connections.

    Rgds
    Carlyle
  20. oh damn. I do not like how this forum double...

    oh damn. I do not like how this forum double posts if there is a hickup in the connection.
  21. Hi, first set your RAM manually using the...

    Hi,

    first set your RAM manually using the RAMS specs. Look at its package. The values to be set are on it. (Something like 17/19/39 or 17/19/19/39)
    Even set the RAM manually to 1.35 volt
    Don'...
  22. Correctly configured within Bios you will only...

    Correctly configured within Bios you will only loose Sata1-Port. Nothing else.
    The second evo will run on 4 pcie lanes from the z370 chipset.
    You will NOT LOOSE 16x GPU connectivitiy .

    Bios:...
  23. sry. double post.

    sry. double post.
  24. What was the vcore max after the stress test...

    What was the vcore max after the stress test please?

    You have cut it off right when the movie got interesting.

    And would you kindly check both boards at the CPU socket.
    Can you see any...
  25. ! Beware of the DIMM.2 SSD placement . It makes...

    ! Beware of the DIMM.2 SSD placement . It makes installing a NH-D15 with two fans tricky, but not impossible.
    Maybe you will take some APEX cover plasic off (which takes one screw more than one...
Results 1 to 25 of 106
Page 1 of 5 1 2 3 4