Search:

Type: Posts; User: Cory29

Page 1 of 6 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    650

    I noticed this too I had to install the AiSuit to...

    I noticed this too I had to install the AiSuit to control it - ive had mixed luck with other software

    Whenever I install a new uefi there seems to be strange ghosting cache issues for about a...
  2. Replies
    4
    Views
    1,139

    your over heating or your ram speed MHZ is set to...

    your over heating or your ram speed MHZ is set to high and its erroring out (im guessing its set to high)

    drop your speed to 2933 and keep dropping it till it doesn't crash -- this board is really...
  3. no I had to turn that off too i think the uefi...

    no I had to turn that off too i think the uefi has a bad api call or something -- I just have the sleep mode turn off the screen and I leave the harddrives on -- its not a solution but it fit my...
  4. I have had this since the release of ZE .. I just...

    I have had this since the release of ZE .. I just disabled sleep .. reported a few times with no response ... good luck
  5. Replies
    9
    Views
    547

    I have the xscp block no complaints HardOCP -...

    I have the xscp block no complaints
    HardOCP - as probably the most honest reviews for tr4 coolers he also has close to 2 hours worth of how to apply tim to the thread-ripper series

    D5 is a D5...
  6. Replies
    9
    Views
    547

    on an year old water cooling loop not cleaned I...

    on an year old water cooling loop not cleaned I sit at (cpu) 30c - 40c idle in a warm room (65f-75f) after heavy use on a 1950x tdie .. other sensors see jumps as high as 80.

    water cooling isn't...
  7. Personally I could get very few games to run in 4...

    Personally I could get very few games to run in 4 way sli - and have less issues with 2 way but still run into stuttering and crashing too ...

    this is on both amd and intel platforms support...
  8. I went from 1601 to 1701(official) and now every...

    I went from 1601 to 1701(official) and now every time I shut down the computer will shut down windows and the screens will turn off but the board is still lit and fans will stay running. I have to...
  9. Replies
    15
    Views
    8,741

    Sticky: UEFI 1701 fan profiles created in UEFI do not...

    UEFI 1701

    fan profiles created in UEFI do not apply to windows on restart unless you open to load UEFI menu (f2) first

    Computer unable to shutdown windows closes but the motherboard is still on...
  10. Replies
    20
    Views
    2,726

    at this point I would swap the powersupply (with...

    at this point I would swap the powersupply (with a hopefully older build you have in your house)
    its very unlikely your shorting to the case since the board is basically covered in a front plate...
  11. Thread: Bios 1701

    by Cory29
    Replies
    7
    Views
    2,124

    elmors 1601 has been great .. hope this is just...

    elmors 1601 has been great .. hope this is just as good
  12. Replies
    20
    Views
    2,726

    it could also be bad timming on the ram if your...

    it could also be bad timming on the ram if your using pre-set profiles -- on almost all ram if I set the xmp/docp then drop the speed to 2933 ** I hit the first stable speed then I try to tweek up...
  13. Replies
    20
    Views
    2,726

    "only happened when the computer was at idle" ...

    "only happened when the computer was at idle"

    are you sure your computer isnt going into sleep mode and getting stuck - the zenith had this issue since day one only the last 3 bios has it seemed...
  14. Replies
    7
    Views
    702

    HWiNFO - sensors tab - should show you all the...

    HWiNFO - sensors tab - should show you all the sensor nodes on the chip and temps
    * this was glitch the zenith extreme had on first launch took a few months for asus to fix a few people had to take...
  15. Replies
    13
    Views
    842

    are you running at 3600 ? with xmp profile...

    are you running at 3600 ? with xmp profile default on ? (not sure what not overclocked means, some people think that rated speeds are not overclocked with memory)
    ** the problems you say you are...
  16. Replies
    325
    Views
    76,485

    Sticky: Off states not saving correctly and changing over...

    Off states not saving correctly and changing over time and restarts

    games that can sync with RGB will crash like COD

    only way to correct issue is to uninstall and install an order version just...
  17. they still have yet to do anything with the...

    they still have yet to do anything with the wb_sensor of there current board .. and the ai_suit needed to read most the sensors - has had issues *most if not all the time
  18. Replies
    2
    Views
    729

    go to easy mode i think f7 then pick a ram profile

    go to easy mode i think f7 then pick a ram profile
  19. Replies
    12
    Views
    2,737

    At lest this time there not hiding the fact this...

    At lest this time there not hiding the fact this board will be stuck in the state of Alpha for its lifetime
  20. Replies
    22
    Views
    6,206

    *reviewers a couple of weeks ago pre launch were...

    *reviewers a couple of weeks ago pre launch were complaining about thread-ripper and this card some said they could get it to boot only if they disabled cores that the card only used 2 cores when...
  21. I have 3200 sticks 64GB .. and im stuck at 2933...

    I have 3200 sticks 64GB .. and im stuck at 2933 stable -- I can boot higher but have not been able to find something stable

    people who get higher clocks stable seem to only be running 2 once in a...
  22. I have had some strange things happen with it too...

    I have had some strange things happen with it too

    maybe windows tried to install its own driver like it dose with everything else

    usually reinstalling the driver and restarting fixes any...
  23. I have had strange issues with new bios updates...

    I have had strange issues with new bios updates were I would get bugs others people were not having .. to correct the issue I re-flashed back and forth a few times 4-5 times

    don't know if this...
  24. Replies
    6
    Views
    1,651

    yeah i just went by the last number 16 and...

    yeah i just went by the last number 16 and assumed 2 x 16
  25. LOL I guess you missed what happened with EK and...

    LOL I guess you missed what happened with EK and there TR4 blocks ;)
Results 1 to 25 of 131
Page 1 of 6 1 2 3 4