Search:

Type: Posts; User: Silent Scone@ROG

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Hello, Yes memory instability can quite easily...

    Hello,

    Yes memory instability can quite easily cause driver crashes in this way.

    There likely wasn't any reason to RMA the memory. If using DOCP/XMP then the applied overclock wasn't stable and...
  2. Replies
    2
    Views
    64

    Hello, Try entering a manual value under the...

    Hello,

    Try entering a manual value under the AMD Overclocking Menu for PBO settings.
  3. Replies
    16
    Views
    1,190

    Hello, 1. For best performance, a 1:1 ratio on...

    Hello,

    1. For best performance, a 1:1 ratio on FClock is crucial.

    2. 2000FCLK is out of the range of a vast majority of CPU samples, I'm not sure what drew you to a 4GHz memory kit if looking...
  4. Hello, CPU should work fine. Flash to the...

    Hello,

    CPU should work fine. Flash to the latest UEFI for the latest AGESA using USB Flashback, however this isn't essential. Beyond memory tuning, performance delta between platforms should be...
  5. There are plenty of good ways to test memory...

    There are plenty of good ways to test memory stability. Use HCI Memtest or Karhu Ramtest. Mixing memory kits remains a fundamentally bad idea if not looking to tweak settings, always purchase single...
  6. You may want to try tuning IOD VDDG and CCD, too....

    You may want to try tuning IOD VDDG and CCD, too.

    If not wanting to dial in the overclock, next rational step would be to reduce the FCLK and memory frequency.
  7. Replies
    5
    Views
    162

    Hello, Manual adjustment of the core ratios is...

    Hello,

    Manual adjustment of the core ratios is fairly fruitless on this platform.

    Clear the CMOS, enable Precision Boost Overdrive along with DOCP and run a memory stress test such as HCI...
  8. Replies
    4
    Views
    266

    MS have acknowledged there are issues with this...

    MS have acknowledged there are issues with this particular update: https://www.windowslatest.com/2021/02/16/microsoft-admits-windows-10-kb4601319-issue-promises-fix/


    Feel free to join the...
  9. Hello, 1. Which memory tests did you run and...

    Hello,

    1. Which memory tests did you run and for how much coverage?

    2. WHEA errors aren't necessarily caused by memory instability, however try tuning VSOC. The Infinity Fabric can be voltage...
  10. F9 is a training code. Normally means FCLK...

    F9 is a training code. Normally means FCLK instability. Either too high, or insufficient voltage (VSOC) for the given settings. The board failing POST stress tests is there to indicate there is an...
  11. Hello, If you're getting stability issues with...

    Hello,

    If you're getting stability issues with XMP then you might want to dial in the memory overclock. Memory instability from build to build normally indicates the overclock was conditional on...
  12. WIth 4 modules anything around 4K can be...

    WIth 4 modules anything around 4K can be difficult on the platform, even at 2T. Your best bet would be to look to the sub timings. Feel free to try these from my old Z390 Formula system.

    Take...
  13. Hello, It depends what is contained in the XMP...

    Hello,

    It depends what is contained in the XMP profile by the memory vendor. Set the voltage, timings and frequency manually and see if the issue persists. Tuning of the VSOC rail is often needed...
  14. Replies
    2
    Views
    122

    Hello, What is it you're trying to achieve?...

    Hello,

    What is it you're trying to achieve? Manual overclocking core frequency has very little benefit, if any. Enable PBO and DOCP and the CPU will boost as far as intended within thermal and...
  15. Hello, If this is your first build I would...

    Hello,

    If this is your first build I would advise against purchasing high speed high density kits. At that capacity, look to GSKILL and around the 3200Mhz mark.

    High density kits above this...
  16. Replies
    2
    Views
    247

    Would need to know what variables have changed....

    Would need to know what variables have changed. Drivers, etc. Check real world performance rather than relying on Futuremark synthetic scores. Sys info and other factors can have an impact on the...
  17. For best performance you want to be running 1:1...

    For best performance you want to be running 1:1 ratio with the FClock (FCLK). Aim for 3600-3866 with that kit and dial down timings from there.
  18. Make sure you're pressing the Flashback button...

    Make sure you're pressing the Flashback button and not the BIOS reset.
  19. USB Flashback will work if following the process...

    USB Flashback will work if following the process correctly.

    Make sure the pen drive is

    1) Freshly formatted to FAT32

    2) In the correct USB slot

    3)The file is renamed to M12E.CAP
  20. Renaming is only a function needed for USB...

    Renaming is only a function needed for USB Flashback, use this feature as suggested above if wanting to roll back.
  21. Try XMP Profile 1, too. Failing that, look to the...

    Try XMP Profile 1, too. Failing that, look to the sub timings.
  22. You may wish to tune lower for reasons stated...

    You may wish to tune lower for reasons stated above.
  23. Please PM me which nickname you want

    Please PM me which nickname you want
  24. Undervolting Ampere is one of the best things you...

    Undervolting Ampere is one of the best things you can do. The silicon is stretched quite thin as it is, so reducing power consumption is beneficial in order to find the best ratio at voltage points...
  25. 1.45v is fine for those modules. I've been...

    1.45v is fine for those modules. I've been running this in my personal system for over 18 months. You may need to pump VSOC higher on that CPU as first generation Ryzen can often have weak fabric. If...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4