Search:

Type: Posts; User: Praz

Page 5 of 20 FirstFirst 2 3 4 5 6 7 8

Search: Search took 0.08 seconds; generated 124889 minute(s) ago.

  1. Replies
    15
    Views
    7,889

    Hello Fully clear the BIOS, set MultiCore...

    Hello

    Fully clear the BIOS, set MultiCore Enhancement to disabled and leave all other settings at default. Test if the system is still unstable.
  2. Replies
    8
    Views
    25,866

    Hello Thaiphoon Burner does not support SPD...

    Hello

    Thaiphoon Burner does not support SPD access on the X299 platform.
  3. Replies
    114
    Views
    31,956

    Hello Brighttail stated that he believed the...

    Hello

    Brighttail stated that he believed the cost of the key was not factored into the pricing and I replied that based on the board's manual that was most likely correct. Your reply makes no...
  4. Replies
    114
    Views
    31,956

    Hello This is probably an accurate assumption....

    Hello

    This is probably an accurate assumption. ASUS X299 motherboard manuals state the key will need to be purchased separately as well as stating functionality is for Intel SSDs only.
  5. Replies
    114
    Views
    31,956

    Hello Perhaps the manufacturer of your...

    Hello

    Perhaps the manufacturer of your motherboard has a forum that has less negativity.
  6. Replies
    4
    Views
    4,971

    Hello BIOS profiles saved from one version of...

    Hello

    BIOS profiles saved from one version of the BIOS cannot be loaded to a different version. Because of possible changes from one version to the next this constraint is only prudent.
  7. Replies
    11
    Views
    10,623

    Hello The applied voltage is not the same for...

    Hello

    The applied voltage is not the same for AVX and non-AVX loads. Intel has programmed the VID table differently depending on AVX usage so this is not as cut and dried as one would think. I...
  8. Replies
    10
    Views
    3,032

    Hello That is not a valid value for adaptive...

    Hello

    That is not a valid value for adaptive voltage. The entered voltage is required to be larger than Intel's programmed voltage.
  9. Replies
    11
    Views
    3,366

    Hewllo Don't turn off the power supply or...

    Hewllo

    Don't turn off the power supply or disconnect power from the wall.
  10. Replies
    114
    Views
    31,956

    Hello It would be best to wait and see how...

    Hello

    It would be best to wait and see how things shake out regarding the availability of the keys. It is still early days for this technology. I would not count on support for non-Intel drives...
  11. Hello The adaptive voltage value needs to be...

    Hello

    The adaptive voltage value needs to be set higher than the programmed VID value. A lower set value will result in Intel's default voltage being used. Has been this way on all platforms that...
  12. Replies
    15
    Views
    25,173

    Hello Increase the CPU power limit to 140%....

    Hello

    Increase the CPU power limit to 140%. The Core VID values shown in HWINFO are irrelevant for voltage monitoring.
  13. Hello SVID control does work. The result is...

    Hello

    SVID control does work. The result is dependent on Intel's programmed voltage algorithms and correctly set associated BIOS settings. Voltage reported by software can be off 0.030V or more as...
  14. Hello Z370-A here. VCORE will be close to...

    Hello


    Z370-A here. VCORE will be close to what is expected with correct tuning. Need to keep in mind the reported voltage inaccuracies depending on the software and physical connections of...
  15. Replies
    13
    Views
    8,641

    Hello Perform a fresh install of the operating...

    Hello

    Perform a fresh install of the operating system.
  16. Replies
    16
    Views
    17,368

    Hello Thread cleaned up. JustinThyme, please...

    Hello

    Thread cleaned up. JustinThyme, please review the rules for this section of the forum. Post back with the pertinent information such as your case id # and the other steps you have taken.
    ...
  17. Hello After a full BIOS reset using default...

    Hello

    After a full BIOS reset using default settings if the issue is no longer present with multiple shutdowns/reboots the problem is in the tuning and will need to be dialed in by the user.
  18. Replies
    23
    Views
    12,433

    Hello Set the memory voltage to the spec'd...

    Hello

    Set the memory voltage to the spec'd 1.35V.
  19. Replies
    15
    Views
    5,118

    Hello I guess I'm not understanding something...

    Hello

    I guess I'm not understanding something here. What does any 3200MHz kit have to do with the 3600MHz kit you purchased?
  20. Replies
    15
    Views
    5,118

    Hello G.Skill, at their website, lists that...

    Hello

    G.Skill, at their website, lists that model for Intel only. Neither G.Skill nor ASUS show any kits qualified for your system at the speed and density you have purchased.
  21. Replies
    15
    Views
    5,118

    Hello G.Skill does not have a 3600MHz 64GB kit...

    Hello

    G.Skill does not have a 3600MHz 64GB kit qualified for the Zenith Extreme. A better choice would have been dropping down a couple of speed bins from the max memory specs of the motherboard...
  22. Replies
    5
    Views
    3,631

    Hello Adjust LLC to tune the loaded VCORE. And...

    Hello

    Adjust LLC to tune the loaded VCORE. And if necessary fine tune the IA AC and DC load lines.
  23. Hello I'm not complaining about anything. And...

    Hello

    I'm not complaining about anything. And the BIOS version is irrelevant to the content I posted. Without tuning I was seeing 0.050V - 0.060V VDROOP. With proper tuning under load the DROOP...
  24. Hello ASUS Z370-A with no LLC control....

    Hello

    ASUS Z370-A with no LLC control. Adaptive voltage mode used with additional turbo voltage set to 1.340V and LLC left at default (auto). CPU-Z and HWINFO used for software reporting and 5.5...
  25. Hello Without an overclock the adaptive...

    Hello

    Without an overclock the adaptive voltage mode is non-existent. Applying an offset in that mode is identical to using the offset mode. A manually set offset voltage is never ignored and is...
Results 101 to 125 of 497
Page 5 of 20 FirstFirst 2 3 4 5 6 7 8