Search:

Type: Posts; User: Praz

Page 6 of 20 FirstFirst 3 4 5 6 7 8 9

Search: Search took 0.08 seconds; generated 133444 minute(s) ago.

  1. Hello Check the CPU socket for bent or damaged...

    Hello

    Check the CPU socket for bent or damaged pins. Also be sure the cooler/water block is properly tightened when reinstalled.
  2. Hello LLC is for VCCIN not VCORE. There will...

    Hello

    LLC is for VCCIN not VCORE. There will be not type of chart for these voltages as Intel programs the VID tables per the requirement of each individual CPU.
  3. Hello Taking into consideration the slight...

    Hello

    Taking into consideration the slight variance because of bit resolution and impedance TurboV is pretty much dead on compared to actual voltage here. Of course the exception is VCORE if using...
  4. Thread: Rampage VI Apex

    by Praz
    Replies
    9
    Views
    4,009

    Hello This is a non-issue. The ASUS EZ...

    Hello

    This is a non-issue. The ASUS EZ Installer for Win 7 is available in the utilities section of the Win10 drivers. This is the only driver/utility required for installing Win7. The listed...
  5. Replies
    19
    Views
    7,248

    Hello The contact layout is secondary to the...

    Hello

    The contact layout is secondary to the issue of this thread. This issue was solved as noted in the post above yours by replacing the faulty graphics card. If you are having an issue with...
  6. Thread: Asus Sucks!

    by Praz
    Replies
    15
    Views
    7,639

    Hello Move the whining to the General...

    Hello

    Move the whining to the General Discussion section of the forum or if a specific open case or RMA issue post in the Service Related Inquiries section. Thread closed.
  7. Replies
    38
    Views
    17,374

    Hello Memtest is pretty much useless with...

    Hello

    Memtest is pretty much useless with today's platforms. Better testing would be employing HCI or GSAT to weed out memory issues. I see no problems using Photoshop with 0702 so memory...
  8. Hello Will be up and running in the next...

    Hello

    Will be up and running in the next couple of days. :)



    66737
  9. Replies
    18
    Views
    5,325

    Threads merged

    Threads merged
  10. Hello XMP does not and has never set all...

    Hello

    XMP does not and has never set all memory timings. If you have memory that is not capable of the optimization 0503 provide flash to 0031. that is why it was released.
  11. Replies
    117
    Views
    95,231

    Sticky: Hello Why is that? 96 Ohm or greater impedance...

    Hello

    Why is that? 96 Ohm or greater impedance will have absolutely no detrimental effect other than affecting stability if that chosen setting is not correct.
  12. Replies
    9
    Views
    8,596

    Hello There is a misprint in the manual for...

    Hello


    There is a misprint in the manual for the STRIX X299-E GAMING regarding USB BIOS Flashback. The correct USB port is the bottom port (closest to the board) next to the BIOS Flashback...
  13. Hello It seems some of the non-primary timings...

    Hello

    It seems some of the non-primary timings have been tightened for better performance. Manually setting these timings should allow mainstream memory to run at rated speed. Premium memory...
  14. Replies
    10
    Views
    3,614

    Hello Looks up-to-date to me. 66075

    Hello

    Looks up-to-date to me.



    66075
  15. Replies
    2,718
    Views
    1,783,541

    Hello THe 3600C15 GTZ 16GB kits can do 3600MHz...

    Hello

    THe 3600C15 GTZ 16GB kits can do 3600MHz at their rated timings and speed. In fact they are capable of 14-14-14 1T at 3600MHz.
    ...
  16. Replies
    5
    Views
    2,094

    Hello While using 2 8GB density modules...

    Hello

    While using 2 8GB density modules instead of 4 will result in a better chance of 3600MHz memory speed this speed is a pipe dream for most if stability and reliability is a requirement. This...
  17. Replies
    1
    Views
    1,146

    Hello One thread concerning this is plenty. ...

    Hello

    One thread concerning this is plenty.

    https://rog.asus.com/forum/showthread.php?94322-X299-VRM-Disaster-(overheat)
  18. Replies
    2,718
    Views
    1,783,541

    Hello The BIOS versions in this thread are for...

    Hello

    The BIOS versions in this thread are for the non-WiFi C6H. Fortunately the board will not allow flashing an incorrect BIOS.
  19. Hello The OP is wanting 32GB at 3200MHz plug...

    Hello

    The OP is wanting 32GB at 3200MHz plug n' play. There is no memory kit guaranteed to meet those demands.
  20. Hello XMP is an Intel memory specification...

    Hello

    XMP is an Intel memory specification which AMD has not stated they have embraced. Anyone thinking that XMP would be plug 'n play on an AMD platform and then whining because the results are...
  21. Hello There does not seem to be anything wrong...

    Hello

    There does not seem to be anything wrong with your English. In fact this post confirms the takeaway I got from your initial post. Both the Flare X and FORTIS 2 x 16GB 2400MHz kits are...
  22. Hello These two sentences seem to be at odds...

    Hello

    These two sentences seem to be at odds with each other. First you state overclocked memory is a necessity for your usage requirements then comment about not being experienced in overclocking...
  23. Replies
    21
    Views
    7,512

    Hello The memory is being mapped for non-use...

    Hello

    The memory is being mapped for non-use do to instability and the resultant training failure. The BIOS flashing will not be an issue if clearing the BIOS before the flash as should always be...
  24. Replies
    22
    Views
    6,944

    Thread closed. Any further disrespectful posts...

    Thread closed. Any further disrespectful posts will result in the loss of posting privileges.
  25. Replies
    117
    Views
    95,231

    Sticky: Hello I have used several different sets of...

    Hello

    I have used several different sets of memory both 8GB and 16GB density modules. Although I have found stability with ODT values ranging from 34.3 through 96 Ohms I don't believe I have ever...
Results 126 to 150 of 497
Page 6 of 20 FirstFirst 3 4 5 6 7 8 9