Search:

Type: Posts; User: Falkentyne

Page 2 of 8 1 2 3 4 5

Search: Search took 0.01 seconds; generated 69728 minute(s) ago.

  1. Replies
    624
    Views
    111,439

    0707 is older than the Test bioses (at least code...

    0707 is older than the Test bioses (at least code wise) from the Apex (0088) and Extreme (0098)
    That's why the PPD and TXP settings are not there.
    The OLED firmware is identical on them.

    The...
  2. Replies
    624
    Views
    111,439

    Thank you. Looks like you were using 1.30v Bios...

    Thank you.
    Looks like you were using 1.30v Bios set + LLC8, is that correct?
    What stress test were you running?
  3. Replies
    624
    Views
    111,439

    Can you please take a hwinfo64 screenshot with...

    Can you please take a hwinfo64 screenshot with your stress test, at idle and another at full load?
    Make sure your CPU current (Amps), cpu power, both in "Asus EC" and the vcore, are clearly shown in...
  4. Replies
    624
    Views
    111,439

    Did you look at the LOAD voltage between each...

    Did you look at the LOAD voltage between each bios version and confirm that the load voltage is the same?
    Because a 60mv vcore decrease between two bios versions, on the *CPU* is completely...
  5. Replies
    624
    Views
    111,439

    Did you test each set of 2 sticks in A and B, and...

    Did you test each set of 2 sticks in A and B, and both sets worked stable as 2x8 GB sets?

    If yes, then you are correct, 4x8 GB will not work with that board at XMP without a BIOS update or some...
  6. Replies
    624
    Views
    111,439

    This board is daisy chain so we need to find out...

    This board is daisy chain so we need to find out if the sticks are bad so you need to do this.

    1) Go into tweaker's paradise and set DDR Termination Voltage (DDR VTT) to 0.750v. Then set DDR...
  7. Replies
    72
    Views
    24,764

    That's not very helpful. Open a command prompt...

    That's not very helpful.
    Open a command prompt as administrator and then run Install.cmd directly from the command prompt.
    The easiest way is to install a powertool that lets you "Shift+Right...
  8. I have it at 600khz now. I noticed 'some' minor...

    I have it at 600khz now.
    I noticed 'some' minor improvements messing around with FMA3 prime95 LLC8, going from 300 khz to 500khz (Like the system not insta-BSOD'ing at a low vcore), so I assume...
  9. The voltages you mention are bios voltages or...

    The voltages you mention are bios voltages or load voltages? Sometimes people just jumble them then it's impossible to know what they're referring to.
    What bios voltage set do you need to pass 1...
  10. Replies
    4
    Views
    1,110

    For "CPU Fan error" you set CPU Fan to "Ignore"...

    For "CPU Fan error" you set CPU Fan to "Ignore" in monitoring. Then you can use W+Pump or AIO+Pump headers without an issue.

    The aio/wpump headers are for powering pumps directly and having them...
  11. You need to click "Reset layout" or "restore...

    You need to click "Reset layout" or "restore order" in the preferences for panes. Then re-enable "fixed order".
  12. Replies
    624
    Views
    111,439

    Gsync activated-- there's your problem. Gsync...

    Gsync activated--
    there's your problem.
    Gsync will only work at your monitor's refresh rate range. and there are settings where the FPS will get capped at or right below the refresh rate of your...
  13. Replies
    624
    Views
    111,439

    Is your FPS uncapped? Your GPU will not work at...

    Is your FPS uncapped?
    Your GPU will not work at 100% if

    1) it doesn't need to (it's rendering up the maximum the engine allows).
    2) you're using a FPS capping or vertical sync method.
    3) the...
  14. VRM's operate in hundreds of *KHZ* up to 1 mhz...

    VRM's operate in hundreds of *KHZ* up to 1 mhz (1000 khz). A mouse operates up to *1000hz* --ONE khz.
    VRM's have nothing to do with input lag. They have to do with *CPU VCORE* in how the 12v from...
  15. Whoever the hell said it improves input lag...

    Whoever the hell said it improves input lag should be thrown on a tropical island with a half broken Nintendo Switch controller and a solar powered battery AC generator and never be allowed near a...
  16. Replies
    18
    Views
    8,716

    Well guess what? You can't do that. Deal with...

    Well guess what? You can't do that.
    Deal with it. And maybe try listening to what other people are trying to ask you instead of acting elitist, entitled, fat and lazy.
  17. Replies
    624
    Views
    111,439

    Easy solution 1) Disable C1E and C3 2) Set ASPM...

    Easy solution
    1) Disable C1E and C3
    2) Set ASPM Power management to disabled.
    The biggest culprit of lower GPU core is C3 (sometimes C1E) being enabled. People who refuse to disable C-states...
  18. Core #2, 4 and 6 are always the hottest cores on...

    Core #2, 4 and 6 are always the hottest cores on every 10900k CPU (also applies to 9900k). Core #1 is always the coolest core in prime95 SSE2/AVX/FMA3 small FFT. For some reason, this changes a bit...
  19. Replies
    624
    Views
    111,439

    Renaming is only for bios flashback (e.g. without...

    Renaming is only for bios flashback (e.g. without CPU installed or if you can't boot).
    For Ezflash (normal flash) through BIOS, the bios name can be anything you want.
  20. Replies
    9
    Views
    2,363

    You forgot Prime95 112k-112k AVX Disabled. ...

    You forgot Prime95 112k-112k AVX Disabled. AIDA64 Stress FPU is not bad for gamers for a realistic AVX test. It's harder to pass than Prime95 AVX disabled small FFT. Realbench 2.56 is harder to...
  21. Replies
    624
    Views
    111,439

    That's good. And did you try the 0704 bios also?

    That's good. And did you try the 0704 bios also?
  22. Replies
    3
    Views
    2,688

    No need to make two threads asking the exact same...

    No need to make two threads asking the exact same question.
  23. You need a command line flasher to flash these. ...

    You need a command line flasher to flash these. For Gigabyte the file is EFIflash. For Asus, I have absolutely no idea.
    Check win-raid forums and ask there as the people in the bios modding...
  24. Replies
    3
    Views
    306

    What power supply was that? I wasn't aware of...

    What power supply was that?
    I wasn't aware of any decent 1000W's that would do that. What model/brand and when was it purchased?
  25. Replies
    2
    Views
    424

    Normal super i/o resolution. +/- 16mv.

    Normal super i/o resolution. +/- 16mv.
Results 26 to 50 of 192
Page 2 of 8 1 2 3 4 5