Search:

Type: Posts; User: Nate152

Page 1 of 20 1 2 3 4

Search: Search took 0.10 seconds.

  1. Replies
    9
    Views
    165

    Cross your fingers. :)

    Cross your fingers. :)
  2. Replies
    34
    Views
    664

    14-15-15-36 would be the best timings.

    14-15-15-36 would be the best timings.
  3. Replies
    34
    Views
    664

    That sounds ok as long as IO and SA voltages...

    That sounds ok as long as IO and SA voltages aren't too high, otherwise you'll have to loosen timings until you find stability.
  4. Replies
    9
    Views
    165

    Were you able to hit 4266MHz ?

    Were you able to hit 4266MHz ?
  5. Replies
    2
    Views
    108

    Hi Tom Tromboni I believe you are referring to...

    Hi Tom Tromboni

    I believe you are referring to the motherboard disc?

    After a windows 10 install, I only install the Realtek audio driver and update the graphics driver.

    Everything else is...
  6. Replies
    34
    Views
    664

    It sounds like you're almost there. Would try:...

    It sounds like you're almost there.

    Would try:

    Dram frequency - 3000MHz
    Dram voltage - 1.50v
    IO - 1.275v
    SA - 1.30v

    Primary timings 15-15-15-35-1T
  7. Replies
    9
    Views
    165

    It could be a struggle to get 4266MHz stable. ...

    It could be a struggle to get 4266MHz stable.

    I have the Maximus IX Code (Z270) with the 7700k, the board supports up to 4133MHz but I cannot get it at that frequency. The best I can do is 4000MHz...
  8. Replies
    9
    Views
    165

    My mistake, your title says Z390-F but you...

    My mistake, your title says Z390-F but you mention Z370-F in your post.

    The Z390-F does support up to 4266MHz so yeah try increasing the BCLK until Dram Frequency reaches 4266MHz.

    Good luck !
  9. Replies
    9
    Views
    165

    Hi digitalizeur You may need to increase the...

    Hi digitalizeur

    You may need to increase the BCLK to reach 4266MHz which will also increase the cpu frequency.

    Your IO and SA voltages are too high at 1.40v, should try and use no more than:
    ...
  10. Replies
    34
    Views
    664

    The RC-RFC1-RFC2-RFC4-RRDL-RRDS-FAW are...

    The RC-RFC1-RFC2-RFC4-RRDL-RRDS-FAW are subtimings as shown after the primary timings, you can enter these manually to see if this helps with stability.

    Or try loosing the the first primary timing...
  11. Replies
    34
    Views
    664

    Hi feedmeink I actually left a little...

    Hi feedmeink

    I actually left a little headroom.

    You can take vccio and system agent voltages to 1.30v and Dram voltage to 1.50v but I don't know how hard pegadroid wants to push voltages.
  12. Replies
    34
    Views
    664

    Thank you It looks like your cpu's IMC is...

    Thank you

    It looks like your cpu's IMC is struggling a bit. You can try Dram voltage up to 1.45v, that might get 3200MHz Realbench stable.

    Realbench wouldn't concern me if I could play games...
  13. Replies
    34
    Views
    664

    How far does 2T let you get ? Here's an idea,...

    How far does 2T let you get ?

    Here's an idea,

    I know you paid for 32GB but if you're just gaming, 16GB is plenty and may let you run at the rated specs as 16GB will be lighter on the cpu's...
  14. Replies
    34
    Views
    664

    Ok, Go back into the bios, keep the same...

    Ok,

    Go back into the bios, keep the same settings as above and select the next slowest Dram Frequency.

    F10 and enter.

    If it doesn't boot, select the next slowest Dram Frequency again, keep...
  15. Replies
    34
    Views
    664

    All right Lets try the original specs manually...

    All right

    Lets try the original specs manually instead of using XMP.

    Reset Bios to defaults (F5 key).

    AI Tweaker - Manual
    Dram Frequency - 3466MHz
    Dram voltage - 1.40v
    CPU VCCIO voltage -...
  16. Replies
    34
    Views
    664

    Does your bios have memory OC presets? Instead...

    Does your bios have memory OC presets?

    Instead of using XMP, try one of the Memory OC Presets if you have the option.

    If you have the option, "OC Presets" is listed at or near the top of the AI...
  17. Replies
    34
    Views
    664

    All right I don't think I'd push it any harder...

    All right

    I don't think I'd push it any harder on voltages to get 1T stable.

    The next thing to try is loosening primary timings to 16-16-16-36 - 1T or stick with your original settings with 2T.
  18. Replies
    34
    Views
    664

    All right I don't fool with the secondary...

    All right

    I don't fool with the secondary timings, I let those all on auto and set only the primary timings and command rate.

    Try raising the Dram voltage to 1.40v, if it doesn't boot try Dram...
  19. Replies
    34
    Views
    664

    Hi pegadroid In the bios on the AI Tweaker...

    Hi pegadroid

    In the bios on the AI Tweaker page try setting:

    Dram Frequency - 3000MHz
    Dram voltage 1.40v - 1.45v
    CPU VCCIO voltage - 1.25v
    CPU System Agent voltage - 1.25v

    Primary...
  20. Code 30 and 40 is telling you it came out of...

    Code 30 and 40 is telling you it came out of either the s3 or s4 sleep state.

    Disabling sleep and hibernate should solve it.
  21. Replies
    3
    Views
    244

    Thank you toronto699 Was starting to think...

    Thank you toronto699

    Was starting to think Nvidia forgot about us.
  22. If you have a Maximus X/XI motherboard try...

    If you have a Maximus X/XI motherboard try installing Aura for the motherboard only as they support Aura Sync which lets you control the lighting of your Strix 1070.

    Uninstall Aura for your Strix...
  23. Overclocking the core will give you the most...

    Overclocking the core will give you the most performance gain, a +1000MHz overclock on the Vram should give you an additional 2-3 FPS and can help games run smoother.
  24. My Strix 1070 has Samsung memory and can hit...

    My Strix 1070 has Samsung memory and can hit almost a 1400MHz overclock.

    You should see a 10 FPS increase in games with both the core and memory overclocked.
  25. You can probably squeeze a little more out of it...

    You can probably squeeze a little more out of it with the voltage increased, you won't damage it with Nvidia capping the voltage. But on the other hand if you're happy with where it is that's fine...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4